Line
-
Product
Teleprotection
-
Schweitzer Engineering Laboratories, Inc.
Teleprotection systems monitor and protect transmission lines using communications-assisted coordination between relays.
-
Product
General Inclinometers
-
Columbia Research Laboratories
Columbia's SI-701 Series of Inclinometers are electronic tilt sensors based on Force Balance Accelerometer technology. They produce high level low impedance output proportional to the sine of the tilt angle. Model SI-701B is a low cost general purpose sensor that can be up-graded with the addition of the Columbia "HP" torquer system (SI-701BI) for greater accuracy and ruggedness. A bi-axial version of both units (SI-702B) is also available. The Model SI-701BI is designed with an output circuit made for 4-20mA data transmission systems for industrial applications. The model SI-701FND is a fluid dampened premium performance inclinometer designed to produce accurate tilt data in extreme shock and vibration environments. The latest addition in the line is Model SI-701WPBI, a waterproof (to 150 feet) inclinometer which operates from a +15 volt supply with 4-20mA output. A single power supply powers both the sensor and the 4-20mA line driver.
-
Product
Autocompute LCR-Q Meter
Model 4910
-
Aplab Model 4910 is a microprocessor based digital Autocompute LCR-Q Meter that meets today’s laboratory requirements, in the production line and the quality assurance area. It features fully autoranging and automatic operation over a wide range of measurements. Model 4910 measures inductance, capacitance, resistance and quality factor to a basic accuracy of ±0.25% of the reading for values upto 2000H, 2000μF, 2M ohm and Q factor upto 99 respectively. Measurements can be made at a frequency of 100Hz or 1KHz as required and either the series equivalent or parallel equivalent component values can be displayed.
-
Product
BGA SMT Adapters
Giga-snaP™
-
Giga-snaP™ 0.75, 0.8, 1.0, and 1.27mm pitch BGA Surface Mount Feet Adapter line of products provide an inexpensive and reliable method for attaching BGA chips to target board. The product line consists of patented female sockets with machined pins epoxy over-molded into an assembly that matches a particular BGA pattern. The epoxy over-molded female BGA socket is soldered to a PCB using standard soldering methods. A corresponding male pin BGA adapter, to which the user attaches their BGA chip, is plugged into the female socket on the board thus interconnecting the chip and the system is ready to go. The SMT adapters have the same solder ball types as the chips they are emulating. These adapters have less than half of the insertion force of competitive adapters, shorter electrical path for highest speed, and can be solder reflowed numerous times. A complete description and drawings of Giga-snaP™ 0.75, 0.8, 1.0, and 1.27mm pitch BGA Surface Mount Feet Adapters can be found at the tables shown below.
-
Product
MiniFlash FPA Vision Autosampler
-
The MINIFLASH FPA Vision Autosampler is the latest addition to the Vision-series product line, an automated accessory specifically developed for use with the MINIFLASH FP Vision analyzer. (Photo shows FP Vision and Autosampler). The modular design offers the flexibility to expand with an autosampler anytime. MINIFLASH FPA Vision autosampler can be used interchangeably with all FP Vision Series analyzers.
-
Product
Detectors - RF / Microwave
-
PMI offers a full line of RF and Microwave detector products that range from 2 MHz up to 40.0 GHz. Many options are available. If you do not see exactly what you require on this web site please contact
-
Product
High Soeed CMOS System on Chip (SoC) Line Scan Image Sensor
LS4k
-
The LS4k is a high speed CMOS System on Chip (SoC) line scan image sensor optimized for applications requiring short exposure times and high accuracy line rates. It incorporates on chip two pixel arrays consisting of 2 rows with 4,096 7µm pitch pixels and 4 rows with 2,048 14µm pitch pixels respectively, a high accuracy (12-bit) high speed (84MHz) analog-to-digital conversion (ADC), and sophisticated on chip optical calibration for PRNU, DSNU, and lens shading correction.
-
Product
Embedded Systems
-
Embedded systems consist of computer hardware, input and output (I/O), and software typically used for system control or monitoring applications. Our engineers are experts at integrating control system electronics with components and sensors, including motors, pumps, valves, signal transducers, and much more. We have developed and deployed thousands of systems that include industrial assembly lines, scientific instruments, medical devices, large installations like factories, manufacturing equipment, and electrical grids that rely on multiple embedded systems networked together.
-
Product
NI-9425, 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module
785044-01
Digital Module
24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module - The NI‑9425 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels. The NI‑9425 offers isolation between the input and output banks from channel to earth ground. You cannot use the NI‑9425 in a CompactDAQ chassis to perform counter operations.
-
Product
Video Cross Line Generator
CL5410
-
The CL5410 can generate up to 4 lines at once and each line may be on a horizontal or vertical axis. This allows the CL5410 to replace the CL5400C, CL5404C and CL5405C and retain all of the functionality of each unit and more. The CL5410 is built on a new platform and allows a wide variety of options to be selected in the menu system. However, even with the enhanced menus, the CL5410 still has the same legendary ease of use like our previous models. That means enough buttons to change commonly used setting easily without the hassle of a menu..
-
Product
Sonde Point Transmitter
-
Sondes are used to trace the path of non-metallic pipes and locate line blockages.
-
Product
PXIe-7966, Virtex-5 SX95T FPGA, 512 MB DRAM PXI FPGA Module for FlexRIO
781805-01
FPGA Module
Virtex-5 SX95T FPGA, 512 MB DRAM PXI FPGA Module for FlexRIO—The PXIe‑7966 provides flexible, customizable I/O for LabVIEW FPGA. It includes 132 single-ended I/O lines configurable as 66 differential pairs. You can pair the PXIe‑7966 with FlexRIO adapter modules that offer high-performance analog and digital I/O. Together, the two modules create a reconfigurable instrument that you can program with LabVIEW FPGA software. The PXIe‑7966 supports peer‑to‑peer streaming, which directly transfers data among multiple FPGA modules or select PXI Express modules without sending data to the host processor. With this feature, you can add FPGA capabilities to high-performance NI digitizers with NIST‑traceable calibration or expand your FPGA algorithms across multiple FPGAs for computationally demanding applications.
-
Product
RS232 / RS485 / RS422 / Ethernet Surge Protectors
-
Our passive, rugged, industrial-grade RS232 / RS485 / RS422 / Ethernet surge protectors are designed for direct industrial DIN-rail mounting and they come with two (2) or three (3) stages of surge protection — Gas Discharge Tube (GDT), protection resistors, and Transient Voltage Suppressor (TVS) - for maximum protection. From 2-wire RS485, 4-wire RS422 / RS485, to 10 / 100 / 1000M Ethernet, CommFront's surge protectors safeguard your data lines and provide you with a peace of mind.
-
Product
Organic Pollutant Monitor
OPSA-150
-
The OPSA-150 is a organic pollutant monitor that uses HORIBA's proprietary Rotary Cell Length Modulation, a measuring technique incorporating 25 years of expertise. The unit can be used as an organic pollutant monitor at drainage systems for determining compliance with COD monitoring regulations, for monitoring quality of water measuring levels of organic matter at water supply intakes, and as an organic monitor on process lines (phenol meter).*Pole mount, outdoor cover, and analysis panel are available as options.
-
Product
Function Tester with Low Number of Channels
UTP 6010 RF
-
The UTP 6010 is one of our smallest test systems and therefore a cost-effective entry into our UTP tester series.The fast system is used to implement scalable functional test applications for a test item (single device under test) with multiple RF channels and mixed-signal test options. Depending on the adapter, the DUT can be tested at circuit board level (FKT) or when installed at the end of the line (EOL).Depending on the test item requirements, we configure the appropriate number of channels and integrate the necessary interfaces directly in the adapter or tester. The test speed, production volume and overall complexity of the UTP 6010 interfaces can be varied according to your requirements.
-
Product
MIL-STD-1553 Test & Simulation Interface for VME
VME-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
Hipot Instruments
HypotMAX® Series
-
Our HypotMAX series is a complete Line of automated Hipot instruments designed to meet the demanding requirements of high voltage applications. We've included our patented SmartGFI feature of maximum operator safety protection as well as a variety of advanced features to increase productivity. Setup and run tests up to 20 kV with confidence from our intuitive user interface or automate with PC.
-
Product
Spectrometer
LSCM
-
This device performs high-speed measurement and sorting of LED electrical and optical characteristics while synched with control signals from the LED production line inspection and sorting system. The LSCM then provides that pass/fail information to the system. The LSCM is equipped with the function to test both electrical and optical characteristics by applied voltage and current to the LED. This test device was designed to integrate test functions required by the inspection and sorting system into one compact body.
-
Product
LXI 2.4GHz 50ohm 32x8 Matrix
60-771-001
Matrix Switch Module
The 60-771 is a family of integrated RF matrices suitable for use up to 2.4GHz in a 50 ohm transmission line system. The matrix design permits any single Y input to be connected to any single X input, permitting the concurrent connection of 8 RF paths. All signal paths are bi-directional permitting any connection to be used as an input or an output.
-
Product
Impurity Analysis In Bulk Gas
-
High-purity gas is necessary in industries such as chemical, medical, and foods. Precisely controlled GC enables identification and quantitation of a trace amount of impurities in bulk gas. If the gas resources in a factory consist of multiple lines, a sample line selector SLS-2020 can be utilized to switch sample lines automatically, allowing a single GC to analyze all samples.
-
Product
Safety / Area Sensors
-
Panasonic Industrial Devices Sales Company of America
Panasonic provides general purpose, small object and slim body Area Sensors for detection of intrusions and parts, edges of moving or falling objects and to control access. These compact and ultra-slim picking Sensors with easily visible job indicators verify picking of parts in cell production and assembly line.
-
Product
Automatic Air Purging Tank
MF-015
-
If the fuel passing through a flow detector has mixing of air, the flow rate cannot be measured correctly. The MF-015 is an automatic air purging tank that uses a precision float valve. When fluid enters the flow line, the air is automatically purged to the atmosphere.
-
Product
Signal Generator, Audio, Compact, Handheld, 1 Channel, 20kHz, FM, US Plug
72-490
-
Highly versatile compact audio generator is perfect for sound system and speaker component testing. Its high precision and remote VCO input make it suitable for the serious test environment, yet its compact size and low cost make it suitable for any tool box. This device is designed to be connected to the line level of any consumer or commercial designed audio amplifier. While it is designed to be used with unbalanced inputs, it is also suitable for balanced equipment
-
Product
4U Rackmount Chassis
Chassis
4U rackmount chassis is a cost-effective computer chassis featuring a complete line of backplanes, power and storage device options. The 4U computer chassis provide the best support for various wallmount and rackmount system.
-
Product
Thermal Conductivity Analyzer
Model 2000B
-
Teledyne Analytical Instruments
The Series 2000 represents a complete line of Thermal Conductivity Detector (TCD) based analyzers which can be applied in a wide range of applications and industries. By using field proven filament-based and semiconductor based TC detectors, Teledyne is able to continuously monitor hydrogen and a variety of other gases of interest in either binary or multi-component sample gas streams.
-
Product
6GHz Four Channel Signal Generator
LS6084B
Signal Generator
The LS6084B is a 6GHz Four Channel RF Analog Signal Generator, offers industry leading performance, in an easy to use benchtop box. It features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The design offers excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
-
Product
PXI-6704, 16-Bit, 32-Channel, Static PXI Analog Output Module
777796-01
Analog Output Module
16-Bit, 32-Channel, Static PXI Analog Output Module—The PXI‑6704 is a static analog output device. You can use the PXI‑6704 to create software-timed voltage and current output applications. You can independently set the output voltage range on each channel. The PXI‑6704 also includes eight 5 V TTL/CMOS digital I/O lines.
-
Product
Single Channel Telemetry
-
Our comprehensive line of telemetry products includes battery and induction powered products to meet the most demanding applications in automotive, agricultural, aerospace & defense, wind power plant, test benches, brushless motors and generators, and industrial applications.
-
Product
High Voltage Breakdown Test Sets
HT-Series
-
Dielectric Voltage Withstand Test or High Potential Test (HIPOT test) is a 100% production line test to verify the quality & electrical safety characteristics of products.
-
Product
Pulse AC Method Area Ionizers
ER-X Series
-
Panasonic Industrial Devices Sales Company of America
The ER-X Series Area Ionizers utilize the pulse AC ionization design to achieve high-speed charge removal of wide surface areas for high-volume production lines. In addition to supporting compressed air ionization, the ER-X also features both airless and low-pressure ionization modes for applications where tiny workpieces can be easily blown away. Additional features include automatic ion balance and discharge frequency control (manual control is also possible), flat discharge surface for easy cleaning, discharge needle air barrier design to reduce contamination of the needles, replaceable discharge needle unit for easy maintenance, and a dual head configuration for enhanced charge area and layout (2 different ionizer heads can be connected to a single controller).
