Systems
are interconnected groups of purpose.
See Also: Equipment, Test Systems, System Integrators, System Test
-
product
General Purpose Switching System
LX Series
The LX Series matrices are reliable, low cost, and versatile switching systems. A modular design concept is used. Interchangeable control modules, switch modules, and display modules can be assembled into matrices, multiplexers, or individual switch point configurations. All chassis have full front panel LED displays. Status feedback from all switches is provided.
-
product
RFID Products
Murata's RFID systems realize reliable communication ensuring easy installation. Murata's RFID platform contributes to the realization of loT, through the provision of hardware, software, and communication interfaces.
-
product
Water Activity
Water activity defines the energy status of water in a substance or a system. It describes the amount of water available for hydration of materials.
-
product
Wireless Receivers
Omega offers a full range of wireless reciever options. Form RS232-to-USB transceivers to long-range repeater/receiver systems, and connector/transmitter receivers.
-
product
Low Noise Amplifiers
Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a variety of applications but are primarily suited to airborne, maritime and ground based radar systems. LNAs are primarily intended to minimise added noise whilst providing high gain so design focusses on the parameters associated with the noise response of the amplifier. They are usually the first amplifier in the Radar detection chain and will have the lowest noise figure.
-
product
Operation Support System for Wafer Prober
N-PAF
N-PAF (Network-Based Prober Advanced Function) is a networking system developed for more effective operation and maintenance of multiple wafer probers. Remote operation helps save on labor on the factory floor. An E10-compliant RAM Analyzer can be used for operation management of the system
-
product
PXIe-8880, 2.3 GHz Eight-Core PXI Controller
783513-04
PXIe, 2.3 GHz Eight-Core PXI Controller—The PXIe‑8880 is an Intel Xeon 8‑Core embedded controller for PXI Express systems. You use it for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe‑8880 includes two 10/100/1000BASE‑TX (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive and other peripheral I/O.
-
product
PXI 4 Slot BRIC 220x4 2-pole (5 sub-cards)
40-562A-022-220X4
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
UV Analyzer
ARAD-100
The ideal solution for critical UV curing processes where continuous UV monitoring is required to avoid costly downtime and product returns. The built-in sensors are networked for multiple lamp systems with data logging to PC.
-
product
Audio Analyser
ATB PC Pro
The ATB PC Pro Measuring system is a professional Audio Analyser. The Windows program is combined with the computer’s soundcard, the measurement microphone, the Test-Box and the DVD (CD) for the signals forms an exact and extensive measurement system. The applications for the ATB PC Pro are the speaker development, room acoustic optimise, the installation of car sound systems, the setting of Surround reproduction systems and the noise analyser.
-
product
PXI Digital Multimeters - DMM
All three PXI-DMMs deliver market-leading speed at their price points, measuring up to 15,000 readings/s with a maximum single-reading rate of 66 µs. These fast reading speeds translate into higher test system throughput and lower cost of test. Advanced triggering, enhanced functionality, and a full suite of free software simplify system integration and operation.
-
-
-
product
Compact Measurement System For Steel Wire And Rods With Small Diameters
A glowing hot wire is pulled through the rolling mill at about 120 meters per second during ongoing production. Speed, high temperatures and dirt are special challenges for a high-precision measuring system. Our solution is the Contour Check Wire. It is specially designed for the geometric measurement of wires, rods and rebar and, at 800 Hz, offers the optimum measuring rate for accurate data acquisition. In the uniaxial version, you can check the diameter; in the two- to three-axis version, the ovality can also be determined. The small dimensions and light weight allow a quick and easy integration of the Contour Check Wire into the existing line.
-
product
Fully Automated Centration Testing of Aspheres
AspheroCheck UP
Designed for production environments, the AspheroCheck UP is a measurement system that allows the testing of centration and tilt of aspheric surfaces. It stands out through the complete automation of the measurement process. Proven OptiCentric® measurement technology is integrated for a highly accurate centration testing. The automated positioning of the aspheric sample under test as well as of the non-contact sensor for the off-axis tilt measurement provide the key factors for a fast and precise test result.
-
product
CTEL 6U 6 slot with ATX, P1P4s, P2P3P5l, RoHS
104CTEL606-4046R
CompactPCI CTEL 6U 6 slot with system slot left, H110 bus, ATX connector, fully compliant to the PICMG basic specification 2.0 R3.0, Hot Swap specification 2.1 R1, andv PICMG H.110 Computer Telephony specification 2.5 R1.0.
-
product
3U VPX 1 Slot P&G w VITA 67.3D connector in J2
101V301P05-9003R
Power for 3.3V, 5V and 12V are included, rear connectors are all fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.
-
product
Heavy Duty Dynamometers
MD-7500-HD
Today’s Fleet Managers are faced with many challenges – most important of which is maintaining a healthy bottom line. With fuel costs at an all-time high, these challenges have become increasing difficult. Fleets being transitioned from fossil fuels to electric propulsion also face challenges with durability and range to make sure routes can be completed on time each and every day. To help combat these problems and others facing fleet managers today, Mustang Dynamometer offers the MD-7500-HD Series Chassis Dynamometer – which features the most advanced diagnostic capabilities in the industry. The MD-7500-HD is designed to simulate the driving conditions that fleet vehicles encounter on the road every day in a safe and controlled shop floor environment so that critical engine and drivetrain systems can be evaluated to insure vehicles are performing properly and at maximum efficiency. What’s more, the MD-7500-HD offers several levels of testing capabilities in a modular, compact package and with capabilities that can be upgraded in the future as your needs change. Every vehicle in your fleet can now be tested and validated before and after a repair to ensure proper diagnosis and repairs have been performed. In addition to testing repaired vehicles, the MD-7500-HD can be used to test vehicles on a regular basis as a preventative maintenance measure which decreases unexpected breakdowns and allows fleet management to control fuel costs while reducing repair costs. Periodic testing keeps fuel consumption to a minimum and helps technicians identify suspect components before they fail. A proactive approach to Fleet Service can prevent unexpected engine and or drive-train failure which saves organizations thousands of dollars in lost fair revenues. At the heart of the MD-7500-HD is a set of three air-cooled eddy current power absorbers. Each absorber, or brake, can hold up to 600-hp (total power of 1,800-hp) – more than enough to simulate a fully loaded transit bus. As the systems PAU’s (brakes) are air-cooled, no water is required to or from the device – eliminating the high cost of water consumption and/or the cost of an expensive water recovery system – which can sometimes exceed the cost of the dynamometer system itself. Mustang is the only company that offers a Universal Fleet Test Bed without water supply requirements. AC Motors can be added to simulate regeneration and validate range for organizations that have transitioned to carbon free electric propulsion. The 7500 is the best solution for fleet managers looking to improve their bottom line and offer disruption-free public transportation.
-
product
Systems Modeling
Altair model-based development (MBD) tools drive fast development for smarter connected systems. Altair customers simulate complex products as systems-of-systems throughout your entire development cycle from early concept design to detailed design to hardware-in-the-loop testing (HIL). Explore more by combining mechanical models with electrical models (in 0D, 1D, and/or 3D) to enable multi-disciplinary simulation and leverage automatic code-generation for your next generation embedded systems.
-
product
Laser Diode Drivers (LDD)
LDD technology has evolved from driving DVD/CD/Blue-ray optical drives to include laser projection in smartphones, automotive head-up displays (HUDs) and pico projectors. Renesas has developed new LDDs for RGB scanning laser projection systems and laser-based pico projectors. Automotive HUDs are benefiting from big innovations in MEMS projection systems and are now central to advanced driver assistance systems (ADAS) and safety. The latest laser scanned-MEMS projection systems can provide higher resolution images and at a lower cost.
-
product
Steering Effort Sensing System
Advanced Telemetrics International
Are used to measure steering wheel torque continuously, utilizing a strap-on steering wheel sensor that transmits a real time torque measurement via radio telemetry.
-
product
High precision Concentricity measurements
KONCENTRICK-V2 CONNECTOR
Koncentrik-V2 is a modular measurement system. Fiber or ferrule eccentriccity measurements can be performed using different mechanical modules. Koncentrik-V2 Connector is dedicated to eccentricity measurement of fiber core relative to ferrule envelope.
-
product
6TL36 Plus In-line Test Handler w/Bypass
EA923
- Test handler 6TL36 Plus.- Dual line (bypass)- 1096 x 1875 x 1851mm [WxDxH]- Expandable to form a group with several 6TL36 modules (adapt line to production volumes).- ICT, FCT with RF, ISP or Combined test (ICT+FCT)- Servocontrolled DUT stop (stopper-less system)- Exchange time 3,2s- Max. PCB dimension 600x450mm- 19” rack space for instruments integration: 28UH- Receiver 25 slots in probe plate + 4 slots in push plate- Automatic Conveyor width adjustment- Optional Return Conveyor- High dynamics conveyors (1500 mm/s)- 90mm Top-30mm Bottom Component clearance- SMEMA and Hermes standard- CE
-
product
CompactPCI 6U 4 Slot right justified, 64 bit, P1-2s, P3-5l
105CPCI604-1157
CompactPCI 6U 4 slot 64 bit with system slot right, fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1. User defined VI/O is standard.
-
product
3D Measuring Systems
Measurement systems for mobile, laptops, tablets and other specific electronic equipment, can be achieved using hi-tech materials, such as Rohacell (as used in Aerospace Industry). innco systems 2D and 3D positioning systems are custom designed to meet each new challenge, for mobile phones to wireless network equipment.
-
product
PXI Source Switching Module
40-618-001
The 40-618 PXI Source Switching Module consists of 12 separate 4-channel multiplexers and 44 uncommitted SPST relay contacts in a single width PXI module. Typical applications include signal routing for avionics test systems that conform to the ARINC 608A specification.
-
product
3 Wire (Digital) Earth Resistance Tester
2120 ER
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● 0Ω adjustment.● Battery operated.● Data hold function.● Low battery indication.● Calibration performed with supplied test leads.
-
product
6U Processor Board
VP62107
LinkedHope Intelligent Technologies Co.,Ltd.
VP62107 supports Intel® Xeon-D Processors up to D-1577(16x 1.3GHz). Based on Broadwell microarchitecture, Xeon® Processor D-1577 possessor has 16 computing cores sharing 24MB L3 Cache, and its base operating frequency is 1.3GHz. VP62107 also supports Intel Turbo (automatic overclocking) technology enabling CPU maximum operating frequency up to 2.7GHz. By using Turbo technology of VP62107, users do not have to increase the cost or complexity of the system configuration just to meet the demand of system peak computing performance.
-
product
Universal AC-DC Power Supplies
PS-RS25-5
WINSYSTEMS’ PS-RS25-5 is a small, convection cooled 25W power supply for embedded systems. It is a universal design that accepts 88 to 264VAC input and generates up to 5A of current at +5 volts. The +5 volt output can be adjusted with an on board trimpot. The PS-RS25-5 is small, measuring only 79 x 51 x 28mm.
-
product
Box Compression Tester
These advanced Box Compression Testers are PC-controlled systems primarily used in the packaging industry for determination of the compression strength of cartons, containers, cardboard boxes, etc.
