Showing results: 976 - 990 of 2296 items found.
-
CU-C Series -
Mors Smitt Group
Heavy duty miniature power relays for demanding applications, switching of AC&DC voltages, resistive and/or inductive loads. Integrated magnetic arc blow-out function.
-
ALPHA 1000/1500 Series (CA) -
TDK-Lambda Corp.
*1 to 16 regulated and independent outputs*Power Factor Corrected*No Minimum Load*Fast-on Tab Connections*Wide Range Input*Low Leakage Medical Options
-
-
TOMSAD
*16 hours at full load*Low ripple and noise*Automatic switching CV / CC*Aluminum heat sink*Displays 3 or 4 digit depending on the model
-
TOMSAD
*16 hours at full load*Low ripple and noise*Automatic switching CV / CC*Aluminum heat sink*Displays 3 or 4 digit depending on the model
-
TOMSAD
*16 hours at full load*Low ripple and noise*Automatic switching CV / CC*Aluminum heat sink*Displays 3 or 4 digit depending on the model
-
Ponovo Power Co., Ltd.
In the PHIL (Power Hardware In-Loop) Case Study, the PHIL system consists of a PONOVO 4-Q amplifier, RTDS simulator, DC electronic load unit and PV inverter.
-
A&D Company, Ltd.
The controller of this testing machine automatically applies an appropriate load and puts the extensometer between the gauge lines, etc. after the sample is set. It provides measurement with high repeatability.
-
A615A-TGT-SDK -
Avionics Interface Technologies
ARINC 615A Data Loader Target development kit enables systems developers to embed ARINC 615A compliant data load functionality into avionics target applications.
-
ESENET -
proconX Pty Ltd
ESENET is an Ethernet gateway specifically designed to interfaceWoodward's Easygen series genset controls with Modbus/TCP networks. It interfaces via the load sharing CAN bus with the Woodward controls.
-
ZhangZhou Weihua Electronic co.,ltd
Is a pressure gauge used to measure the pressure of tires on a vehicle. Since tires are rated for specific loads at certain pressure, it is important to keep the pressure of the tire at the optimal amount.
-
Series KD and LD -
Teledyne Defense Electronics Relays & Coax Switch
Your product description goes here.Series KD and LD solid-state relays utilize MIL-PRF-28750 test methods and are packaged in low-profile hermetically sealed cases. They feature fully floating power FET output technology. Options include short-circuit and current overload protection plus a status output line. Switch status returns the true status of the output switch and is optically isolated from the load.MSL 1KD & LD relays are controlled with 15mAdc/3.8Vdc (TTL), and 1mAdc/0.3Vdc (CMOS).Available options include:KD00CK 5Adc, 60Vdc Load KD02CK 5Adc, 60Vdc Load; with switch statusKD20CK 5Adc, 60Vdc Load; with short circuit protectionKD22CK 5Adc, 60Vdc Load; short circuit protection & switch statusLD00CM 10Adc (5Adc without heat sink), 60Vdc LoadLD02CM 10Adc (5Adc without heat sink), 60Vdc Load; with switch statusLD20CM 10Adc (5Adc without heat sink), 60Vdc Load; with short circuit protectionLD22CM 10Adc (5Adc without heat sink), 60Vdc Load; short circuit protection & switch status
-
TA-60 -
Tech-Aid Products
This test fixture will allow servicing of the 60-1321-( ) series of emergency exit light power supply. These supplies are used in many aircraft to annunciate exit lighting when aircraft power failure occurs. The TA-60 test fixture is equivalent to the suggested test fixture in the OEM 60-1321 CMM. The four load lamps are conveniently placed behind an acrylic red lens for proper viewing while performing load test. The bench cable is provided as part of the test fixture.
-
Model KM CAL-904-MK1 -
Kusam Electrical Industries Limited
• 4-20mA (1kΩ Load, 24V Loop Output).• 0-20mA and 0-24mA output ranges.• 0.025% Basic Accuracy.• Auto Ramp and Step functions.• 0-100% output with percentage step option.• 0-24V DC voltage source.• Open loop and overload buzzer alarm.• Low battery indication.• Simple Operation Interface• Warning beeper when output is open• Pollution Degree 2.• Ambient temperature 0~40℃.• Power Consumption 150mA at 24V 1kΩ load
-
North Atlantic Industries
NAI''s AC- and DC-powered Phase Monitors are used to protect three-phase loads from damage due to phase reversals or phase absence. Contacts may be used to disconnect the load or to operate alarm circuits or both. Upon application of power, the output relay energizes if all phases are connected and the phase sequence is ABC. If any phase becomes disconnected or if the phase rotation is abnormal, the relay immediately de-energizes. These monitors are specifically designed for rugged defense and industrial applications.