Showing results: 766 - 780 of 2295 items found.
-
NGL200 -
Rohde & Schwarz GmbH & Co. KG
Due to their high accuracy and fast load recovery time, the R&S®NGL200 power supply series is perfect for challenging applications. Their two-quadrant architecture allows them to function both as a source and a sink to simulate batteries and loads. Their short recovery times enable them to handle fast load changes that occur for example when mobile communications devices switch from sleep mode to transmit mode.
-
E84 SPC -
Get Control, Inc.
300mm equipment manufacturers utilize this off-the-shelf E84 communications controller to provide SEMI E84 compliant communications for their products. With its built-in Load and Unload algorithms it is the perfect E84 communications solution for process tools, stockers, load ports, FOUP buffers, smart storage shelves and simulation load ports. The E84 SPC easily integrates with equipment controllers through a standard serial communications connection.
-
Mosebach Manufacturing Company
GLS (Generator Loading System) is a load bank for use with your generator to load it automatically to your set point. This will keep your generator running at its optimal point and reduce your maintenance costs. Fully programmable by you.
-
-
-
-
72-505 -
Tenma
*Hand held audio generator*20Hz to 150KHz in 46 steps*±0.5dB sine wave output 1.2V RMS (no load) and square wave output SV p-p max (no load)*Dimensions: 150mm × 83mm × 25mm*Low battery indicator
-
Hilkar
Use of nonlinear loads such as power electronics based equipment and electric furnaces have been on the rise for the last decades. Such loads decrease the power quality of the network that they are connected to. One of the most important parameters for defining the power quality is harmonic distortion.
-
Precise Testing Solution
If you want to check the strength of your application or the server’s strength you will need to find out how much load, in terms of the number of users the application can handle. We use the Performance Testing techniques, to check the load an application can handle.
-
MFJ-267 -
MFJ Enterprises, Inc.
1.5 kW Dry Dummy Load has built-in precision, true peak-reading SWR/Wattmeter switchable to external antenna! Worlds most versatile 1.5 kW dummy load has a built-in true peak reading SWR/Wattmeter that you can switch and use independently! Youll find tons of uses! Tune up your transceiver, linear amplifier, or antenna tuner into a safe 50 Ohm dummy load at full power.
-
Radio Ampstik® 2023 -
SensorLink
The Radio Ampstik uses the same current sensor technology as the original SensorLink Ampstik. It quickly takes accurate current measurements and direction of current flow indication. Knowing source and load direction is essential for power system protection, load balancing, and metering.
-
Series LS10 -
Teledyne Defense Electronics Relays & Coax Switch
Series LS10 DC solid-state relays are designed for mounting on printed circuit boards. They facilitate heat-sinking by providing an interface surface. They can switch loads with high starting currents. The nominal switched currents depend on the size of the heat sink These relays use a direct-bonded copper substrate for thermal efficiency and long life.Available options include:LS60DC10C-21 10A, 7-36 Vdc Load; 3-10 Vdc ControlLS60DC10F-21 10A, 7-36 Vdc Load; 7-30 Vdc Control
-
Anchor Test System -
James Instruments Inc.
Two models, each with two different gauge capabilities enable precision readings over a wide range of applications - from light to heavy duty loads. The standard system has a pull stroke of two inches with an option to extend to four inches. The longer pull stroke allows for complete extraction of most fixings in one simple operation. A load diffusion bridge and pyramid are available to keep reaction loads away from the anchor point.
-
PI-41401 -
Pulse Instruments
The PI-41401 is a four channel Clock Driver card capable of operating up to 140 MHz at 3V and 100 MHz at 5V amplitudes into a 50 Ohm load. The PI-41401 has a clock rate of 90 MHz at an amplitude of 5 volts into a 1-MOhm load. Into a high impedance load the output voltage range is from –5 volts to +8 volts with the pulse amplitude ranging from 0V to 9V. When driving a 50 load the voltage range is –2.5 volts to 4.0 volts with the pulse amplitude ranging from effectively 0V to 4.5V. Each channel has a common edgespeed control to vary the rising and falling edges of the output waveform. The adjustable slew rate range, for any amplitude, is the minimum edgespeed of that amplitude times 5. The output pulse amplitude and the load being driven determine the range of variability.
-