Showing results: 1036 - 1050 of 3349 items found.
-
iWave Systems Technologies
iWave’s FPGA-IP Evaluation Add-On FMC Card is designed to meet ANSI/VITA 57.1 FMC Standard. The card supports both High-Pin Count (HPC) & Low-Pin Count (LPC) connector and can be used in an air-cooled environment. FPGA-IP Evaluation Add-On Card can be interfaced with most of the FPGA development kits available in the market. This card also helps to evaluate iWave’s proprietary FPGA Intellectual Property (IP) Cores.
-
CMD Series -
Smiths Interconnect
Smiths Interconnect's versatile, high density CMD connector solution for board to board and wire to board with built in coding and keying as well as ESA qualification
-
KMC Series -
Smiths Interconnect
Smiths Interconnect's KMC series is an ESA qualified, high density board to board and board to wire interconnect available in multiple configurations from 26 to 162 positions
-
MHD/MDD/MDP Series -
Smiths Interconnect
Smiths Interconnect's MHD/MDD/MDP series is an ESA qualified, high density board to board and board to wire interconnect available in up to 400 positions, with available insulators to accommodate coax and power contacts.
-
SparkFun Electronics
This is the SparkFun RJ11 Breakout, two simple breakout boards for the common 6-pin RJ11 connector. These little boards can easily have one of our RJ11 6-Pin Connectors to work with common telephone cables. Each board features standard B/R/Y/G (Black/Red/Yellow/Green) labels on the top of the board to match a standard telephone wire. Additionally, each board has pin numbers on the back side that match with the pins on the connector.
-
JYEBAO Co., Ltd.
Transmission lines for radio frequency (RF) signals traveling from one point in a system to another (e.g., PC board to PC board, PC board to antenna, equipment to antenna, equipment to equipment, etc.).
-
Dynamic Engineering
The Industry Pack mounting hardware kit provides the necessary hardware to mount an IP board to a carrier board.
-
IC-INT-VPX6g -
ELMA Electronic, Inc.
The IC-INT-VPX6g is a 6U OpenVPX Single Board Computer (SBC) with a dual processing node and on-board FPGA. Combined with Ethernet switches and FPGA boards, it is the ideal DSP board to build high-performance embedded computers (HPEC).
-
FT231X -
SparkFun Electronics
Introducing the SparkFun FT231X Breakout board, complete with the full UART hardware handshake feature! The pin-out of this board matches the FTDI cable to work with official Arduino and cloned Arduino boards. It can also be used for general serial applications.
-
0001026-1 / -2 -
VI Control Systems Ltd.
VI Control Systems has designed two converter boards that make it easy to connect data acquisition boards to breadboards and allow easy computer control and monitoring of prototyped electronic circuits. The converter boards are 0.8 x 3.5 inches and have silk-screened pin numbers for every pin on the board. The 68-pin SCSI converter can also be used to connect 68-pin SCSI cables to prototype solder boards that have 0.1 inch centers.
-
Pomona Electronics
Low-profile fine-pitch chips, desnely populated boards, or vertical boards, Pomona test clips connect you with confidence.
-
Pomona Electronics
Low-profile fine-pitch chips, desnely populated boards, or vertical boards, Pomona test clips connect you with confidence.
-
Nordson Corporation
X-Plane technology provides high resolution, high magnification CT functionality anywhere on the board - without cutting the board.
-
EverythingPCB
Printed Circuit Board Testing and Repair Services CM Wings Board Testing Inc. was founded in 1983. Its founding was a direct response to theneed for a truly customer service oriented facility for printed circuit board test and repair.
-
Advantech Co. Ltd.
Advantech offer 6U CompactPCI CPU boards, rear transition modules, peripheral boards, and support for PMC or XMC module.