X-ray Inspection Systems
See Also: Inspection Systems, Automated Fiber Optical inspection Systems
-
Product
NI Semiconductor Test Systems
Test System
The STS delivers the openness and flexibility of the NI PXI platform to the semiconductor production environment. For easy integration into the production test cell, the STS comes with features such as handler/prober integration, spring probe device under test interfacing, STDF data reporting, and system calibration.
-
Product
Image Sensor Test System
IP750
Test System
Teradyne's IP750 series dominates the image sensor tester market with its superior performance and low cost of test. The IP750 delivers high throughput and high parallel test efficiency, broad device test coverage from CCD and CIS, analog and digital capture, and concurrent image sensor and logic testing. In addition, Teradyne's IG-XL software environment provides easy, shorter test program development and easy maintenance.
-
Product
PXIe System Sync Module, 2 Port
M9032A
System Sync Module
The M9032A has a Soft Front Panel (SFP) that provides a graphical user interface to the system sync module. It allows the user to set up the most commonly used functionalities of the module. The SFP also gives you the ability to check the module's connection status, configure the reference clock and IO settings, and perform firmware udpates.
-
Product
SAS Protocol Test System
M124A
Test System
The SAS Sierra M124A Protocol Test System is Teledyne LeCroy's 7th generation protocol analyzer system that provides 100% accurate protocol capture of both SAS (SAS 3.0) and SATA (SATA 3.0). The industry's most widely used test platform for SAS and SATA features unmatched analysis and debug capabilities to help pinpoint problems at every layer of the protocol.
-
Product
VIP Inflight Entertainment Systems
System
Astronics can outfit your entire cabin with the perfect A/V system to match your needs. From a custom monitor to a robust speaker system, Astronics' integrations will improve your inflight entertainment experience.
-
Product
Mezzanine System
5089
System
The 5089 provides eight channels of 12 bit A/D conversion using the Analog Devices AD7328, and is suitable for medium resolution medium speed applications.
-
Product
Image Sensor Testing
IP750Ex-HD Family
Test System
The IP750EX-HD has been the test platform that has enabled the industry to manufacture high quality CCD and CMOS image sensors, and it is the most economical platform to meet the needs of newer technologies such as Time of Flight (ToF) sensors. When you use a smartphone, high performance digital still camera, or in-home security and surveillance system, these applications have image sensors most likely tested by Teradyne’s IP750ExHD.
-
Product
Conformance Test System
TS8980
Test System
The R&S®TS8980 is the most compact full range conformance testing solution on the market for testing in line with requirements from GCF, PTCRB and regulatory bodies. It supports the entire device certification process for RF and RRM, covering the widest range of technologies including 5G NR based on 3GPP and carrier acceptance specifications. The test system is available in various configurations to cover the required scope of testing.
-
Product
Avenir VIP IFE & CMS Systems
System
The new Avenir Line is the next generation of Cabin Management and In-Flight Entertainment Systems (CMS/IFE) from Astronics. Avenir incorporates the latest technologies to deliver native 4K video distribution through the highest bandwidth Ethernet network system in the industry. It also provides a fully customizable experience, which extends to the graphical user interface.
-
Product
Semiconductor Test System
TS-960e
Test System
The GENASYS Semi TS-960e PXI Express Semiconductor Test System is an integrated test platform that offers comparable system features and capabilities found in proprietary ATE systems. Available as a bench top system or with an integrated manipulator, the TS-960e takes full advantage of the PXI architecture to achieve a cost-effective and full-featured test solution for device, SoC and SiP test applications.
-
Product
Photodiode Burn-in Reliability Test System
58606
Test System
The Chroma 58606 PD/APD Burn-in system is a high density, multifunction and temperature controlled module based system for photo diode burn-in and lifetime test. Each module has up to 256 Source Measurement Unit channels which can source current and measure voltage in various scenarios such as one described below. The system can accommodate 7 modules for a total of 1,792 device channels.
-
Product
X-ray Inspection Performance
MXI Quadra 7
-
Ultimate image quality and magnification, Quadra 7 reveals quality defects as small as 0.1 µm. Ideal for root cause failure analysis, wire bond integrity checking, component cracking, MEMS inspection and wafer level components including TSV and wafer bumps.
-
Product
X5 Pack X-Ray Inspection
-
Designed to be integrated into line with built-in automatic reject and available in 300, 500 and 600 mm belt width models, the X5 Pack is perfect for a variety of unpackaged and packaged products.
-
Product
Laser Diode Characterization System
58620
System
The Chroma 58620 Laser Diode Characterization Station is a state-of-the-art full turnkey system specially designed for laser diode testing. Features range from macro inspection of the facet or aperture active area to a full suite of electro-optical parametic tests.
-
Product
Tool, Inspection Depth Gauge, Mini Coax, ITA
910121157
Inspection Tool
Used to verify the depth setting of the center conductor of the ITA mini coax contacts.
-
Product
Test System Optimized for High-Performance Digital and SoC
ULTRAWAVEMX44 and ULTRAWAVEMX20-D16
Test System
Teradyne is the leader in RF/wireless device testing and has a large installed base of UltraFLEX test systems with the UltraWave24 RF instrument. As new devices for handset and base station applications are introduced using mmWave technology, Teradyne’s mmWave instrumentation has expanded in anticipation of new testing demands.
-
Product
X5 XL800 X-Ray Inspection
-
Designed to be integrated into the production process at either the beginning to protect equipment or at the end to protect consumers, the X5 XL 800 is perfect for products such as meat in Euro crates or cheese in bulk boxes.
-
Product
Seno-Con Test System
PANTHER 2K QST
Test System
Qmax Test Technologies Pvt. Ltd.
Panther 2K-QST is a versatile ultra fast Seno-Con test system designed to test high volume ,low to high pin count consumer semiconductor IC’s for its assembly line wire bonding faults. Its innovative test technology helps learn from known good device and test against target device drastically reduces time required to develop Test programs.The operating software is designed in such a way that it is fully user friendly with GUI programming.
-
Product
ESS Performance Test System
Test System
The Energy Storage System (ESS) Performance Test System is used to evaluate, test, and certify the performance of energy storage systems up to 2MW. The system is a configurable platform with over 200 channels of simultaneously measured AC and DC voltages and currents, environmental temperatures, airflow, and communications. Intuitive software provides real-time monitoring and analysis of power, energy and efficiency to adhere with industry standards. The test system interfaces hardware such as load banks, and controls the ESS to simulate utility applications such as peak shaving and frequency regulation.
-
Product
Photonics Wafer Probing Test System
58635
Test System
The advancement of the photonics device technology continues to enable broader and more demanding applications in the industry.
-
Product
USB2.0 Module With 2 CAN Bus Nodes ARINC825 Compliant For Testing & Simulation of Avionic ARINC825/CAN Bus Systems
APU825-2
System
USB2.0 module with 2 CAN bus nodes ARINC825 compliant for testing and simulation of Avionic ARINC825/CAN bus systems.
-
Product
X-Ray Inspection
-
X-ray inspection systems are used wherever defects need to be detected by non-destructive means. The spectrum of use is broad and ranges from quality controls for complex assemblies, to the testing of materials for cracks and air inclusions, to foreign matter inclusions and shape deviations. The trend toward miniaturization, higher packing densities, and the relocation of components to the interior of the assembly require precise X-ray inspections that detect hidden defects quickly and reliably. X-ray systems from Viscom are used for the inspection of series assemblies as well as sampling and prototype controls. They take care of typical inspection tasks in concealed areas such as void controls, THT filling level measurements, and HIP inspections. At the same time, the systems reliably determine defect features such as coplanarity and polarity – at high inspection speeds and in a cost-effective way.
-
Product
X-ray and CT inspection System
UX20
-
Due to the transformation to electric mobility, foundries are increasingly producing larger and more complex components. With its exceptional inspection envelope and the smart Geminy software, the UX20 facilitates fast and precise inspections of cast parts and helps increase overall production efficiency.
-
Product
Regenerative Battery Pack Test System
17020
Test System
Chroma's 17020 is a high precision system specifically designed for secondary battery modules and pack tests. Accurate sources and measurements ensure the test quality that is suitable to perform repetitive and reliable tests that are crucial for battery modules / packs, for both incoming or outgoing inspections as well as capacity, performance, production and qualification testing. Chroma's 17020 system architecture offers regenerative discharge designed to recycle the electric energy sourced by the battery module ei ther back to the channel s in the sys tem performing a charging function or to the utility mains in the most energy efficient manner. This feature saves electricity, reduces the facilities thermal foot print and provides a green solution by reducing the environmental impact on our planet. Chroma's 17020 system is equipped with multiple independent channels to support dedicated charge / discharge tests, on multiple battery modules / packs, each with discrete test characteristics. The channels can easily be paralleled to support higher current requirements. This feature provides the ultimate flexibility between high channel count and high current testing.
-
Product
Inspection System
Pixie
-
3-D Metrology for automation. Pixie is a standard system for automated optical quality inspection. Pixie can be configured with 2 to 5 servo driven axis movement and the high-speed measurement capabilities make it suitable for inline and stand-alone solutions.
-
Product
X-ray inspection system for BLU, LED Long bar products
X-eye 9000LED
-
X-ray Tube100kV / 200uAMin. Resolution5µmTable Size1,500mm X 500 mmDetectorFlat Panel Detector (High sensitivity)Dimension3,620(W) x 1,065(D) x 1,590(H)mm / 850kg
-
Product
Modular Breakout System 8-Pin Power D-type Plugin Module for 40-192
95-192-001
Modular Breakout System
The 95-192-001 Plugin Breakout Module is designed to be fitted to a PXI 40-192 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
Product
Real-Time Operational and Situational Awareness for IoT Systems
Vortex Insight
System
Vortex Insight is a web-based tool that can be used to monitor and manage a Vortex-based system from any location and on any device. It provides views of a Vortex system including statistics associated with DDS entities and system elements active in a live environment. It also provides configurable dashboards for monitoring system behavior through graphs and charts of statistics, including resource usage. Vortex Insight allows users to control the configuration and the QoS of Vortex applications, services and systems.
-
Product
Battery Management (BMS) Environmental Test System
Test System
The BMS Environmental Test System is a configurable platform simulating the essential signals used by Battery Management Systems (BMS) and cell-monitoring modules with the ability to perform environmental testing on multiple BMS units simultaneously. The system implements single-point value testing to evaluate specific BMS functions such as cell over and under voltage scenarios, cell leakage current, lost communications, or faulty system IO.
-
Product
ESD Test System
58154 Series
Test System
ESD (Electrostatic Discharge) Test Systems are PXI/PCI controlled module to simulate electrostatic discharge pulse during electronic device testing. The 58154 series offer both ESD STM5.1-2001-Human Body Model and ESD STM5.2-1999-Machine Model. The user friendly software offers programmable and flexible features, such as sampling test on a wafer, ESD model, ESD pulse polarity, ESD pulse interval in a sequence, and automatic testing function.
