Gel Cell Battery
-
Product
Intelligent Battery Charger-Analyzer for Battery Systems
SuperMini
-
The SuperMini is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries. With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMini can satisfy the requirements of most ( Up to 40 A-hr ) rechargeable battery systems. The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions. Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.
-
Product
Battery Chargers
-
DC Battery ChargersStep-Up & Step-Down DC Source Chargers and Equalizers These units provide up to 600 watts to charge a 12V or 24 V battery systems (1 or 2 banks) from a 12, 24, 32 or 36 volt source. The single-board design incorporates state-of-the-art switch mode technology for unmatched efficiency and ultra-quiet operation. Multiple stages of filtering reduce radiated or conducted noise to very low levels. All Series are capable of charging up to two independent banks of batteries.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel With V/I Readback
41-752A-013
Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Battery Fault Insertion Unit
Fault Insertion Unit
The Battery Fault Insertion Unit (FIU) provides intelligent switching of cell-simulation channels for the Battery Simulator 1200. The switching capability enables simulation of open-circuit and short-to-rail fault conditions on any cell channel for the purposes of battery management system (BMS) testing. Additionally, a four-wire auxiliary input allows you to connect an external digital multimeter (DMM) instrument to any cell channel for very high-accuracy bypass current and cell voltage measurements. Each FIU provides 24 independently-programmable cell-switching channels for one or two 12-cell Battery Simulator 1200 units. Additional Battery Simulator 1200 and FIU instruments can extend functionality up to 120 series-connected cell channels.
-
Product
Battery Testers
-
Shanghai Beha Electronics Co., Ltd.
*can measure the resistance of rechargeable batteries and DC voltage.*can also test Ni-cd, Ni-MH, Li-ion batteries.*DC Voltage measurement.*4-wire resistance measurement.
-
Product
Scienlab Combined Battery Test Solution
SL1133A
test
Solution for testing battery cells with an output power up to ±3 kW and a voltage range up to 6 V.
-
Product
Scienlab Battery Test System – Pack Level, 110 KW Extendable Version
SL1720A
Test System
Keysight’s SL1700A Scienlab Battery Test System – Pack Level Series allows to realistically emulate the environment of the future battery pack application in order to test the high-power battery pack comprehensively and improve its functions and safety. The growing demand of e-mobility increases the need of vast battery test labs for EV battery development.
-
Product
LCD Display Battery Monitor
TE6-0609
-
Hangzhou Tonny Electric & Tools Co., Ltd.
*Plug into a standard 12V/24V power outlet*Two USB outlets for charging 1x standard 1A and 1xhigh *output 2.4A*Voltage is displayed by digital read out to indicate battery*charge level*Flashing LED alarm and warning audible sounder indicates*low battery voltage*Replaceable 3A fuse*Suitable for 12V negative earth systems*Adjustable main plug angle*Ideal for the vehicle that double as a mobile office
-
Product
EV Battery Test System
-
Shenzhen Sinexcel RE Equipment CO., Ltd
5V cell equipment adopts Sinexcel innovative circuit design + high-speed DSP complex algorithm, the detection process supports multi-gear switching; The equipment integrates voltage, temperature, pressure and other auxiliary channels, 20ms high-speed working condition simulation and other practical innovative functions to meet all aspects of battery electrical performance testing.
-
Product
Advanced Lithium Cell Formation System
-
The Series 5302 is the latest in a series of computerized cell formation systems from Maccor, designed primarily for use in the formation of Lithium Ion and Lithium Polymer secondary batteries. New advanced features provide a greater flexibility and range of use compared with previous designs. This additional capability is even achieved at a reduced cost.
-
Product
Wireless Battery System Tester
EECS550
-
Snap-on Tools has launched the new Snap-on EECS550 Wireless Battery System Tester that eliminates the need for a second technician. “The EECS550 maximizes manpower and gets the critical job of battery system testing done with just one set of hands,” says Dave Brekke, product manager for Snap-on. “Snap-on has listened to techs in shops where this work is a daily task. The tester will change the way techs are able to service cars, trucks, motorcycles, golf carts, ATVs and more. From the strong, built-in magnets that hold the tester in place to the easy-to-see, back-lit screen that displays in eight languages and reports battery, starting and charging system conditions, this tester takes productivity to the next level.”
-
Product
Battery Charge And Discharge Test System
9841
-
*Easy user interface*Measure Voltage, Current, Power, KWH, AH, Temperature, Reference Voltage*Accuracy Measure Time*Easy to see now test progress*Can cycle test*Provide Charge, Discharge, Suspend, FOR, LOOP Mode Select*When Charging, set the stop current to stop charging when fully charged so as to avoid overcharging that will damage the battery. When Discharge, set the stop voltage to stop discharge when discharging to lowest so as to avoid over-discharging that will damage the battery. *The test result will be stored to ACCESS data
-
Product
Battery on-line Monitoring Tester
-
HD Power Test Equipment Co.ltd
Battery on-line monitoring system tester is a on-line battery monitoring and auto maintain system for USP,EPS, DC power supply, communication power supply . The tester has the function of monitoring and alerting for a series of parameters such as battery pack voltage, battery pack current, cell battery voltage, cell battery internal resistance, battery environment temperature, Cell Battery negative temperature and battery voltage balance, residual capacity and discharge. It can automatically maintain balance voltage, which used for on-line monitoring 2V and 12V battery.
-
Product
Water Filler for Nickel-Cadmium Cells
MasterFiller
-
The MasterFiller is an instrument designed to deliver measured quantities of distilled water as required in the service of Aircraft Nickel-Cadmium batteries.· The MasterFiller consists of a microprocessor controlled pump with a level sensing probe, a keypad and display and an external 12VDC power supply (or optional battery).· The MasterFiller is part of a system comprising Intelligent Charger-Analyzers and Software for Battery Data Acquisition and Analysis, designed to improve the accuracy and efficiency of the process of testing batteries for airworthiness certification.
-
Product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
-
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
20V Battery Internal Resistance/Voltage Tester
TOB-BVIR
-
Xiamen Tob New Energy Technology Co., Ltd
Portable Internal Resistance Tester for All Batteries 0 - 20V With Charging Adapter. TOB-BVIR Battery internal resistance tester can be used for measuring the Internal Resistance and Open CircuitVoltage of almost all of the commercial batteries such as Secondary battery, Lead acid battery, Nickle cadmium, Nickle-metal Hydride and Li-ion battery.
-
Product
Battery Capacity Analyzer with record storage
603B
-
The 603B handheld battery capacity analyzer tests 6 and 12 volt sealed lead acid batteries with capacities up to 100 ampere hour (Ah). Test results include voltage, state of charge, and internal resistance. This analyzer also features a built-in USB port and internal memory to store battery information, test configuration, and measurement results for up to 50 batteries.
-
Product
Working Electrodes for Flow Cell
-
Our working electrodes for flow cell are mounted in blocks of PEEK. This resin protects the electrodes from external noise and allows researchers to utilize them regardless the content of mobile phase of HPLC because of their hardness and organic slovent-resistance. Glassy carbon is usually chosen for the redox reaction study on liquid chromatography. Platinum, Gold, Carbon paste and Nickel electrodes are utilized for special purporses.
-
Product
Digital Battery Tester with Automatic Test
706
-
Controlled by microprocessor, simply activate the switch once and the #706 applies a precisely timed, 10 second load to the battery. The test results, “OK”,“WEAK” or ”BAD” are then displayed along with the test voltage, until the unit is disconnected. The #706 also tests charging voltage and relative starter current draw.
-
Product
Small Cell/ Outdoor DAS Antennas
-
*Omni, Quasi-omni, Trisector, Cardioid and Bi-sector formats*Pole mounted and Stadium style antenna configuration*High band, low band and dual band models available*Integrates GPS antenna available on select models
-
Product
Battery Tester
BAT-500
-
Amprobe BAT-500 Battery Tester quickly and accurately tests batteries without taking the batteries off-line. This Battery Tester features a comparator function with pass/fail indication, and speed testing of batteries up to 500 Ah. Amprobe BAT-500 Battery Tester, compact and light weight, simultaneously measures battery resistance and voltage up to 40 V.
-
Product
Single Point Aluminium Load Cell
EST-6
-
Technopark Automation & Control
The EST-6 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 600 x 500 mm. This load cell is available in capacities 500 kg and 1000 kg.
-
Product
Flow Cell Kit
EQCMT
-
The two blocks of the EQCMT Flow cell are constructed using PEEK. It gives a high resistivity for chemical compounds.As well as QCM, these cell is reversible. With a inverted position of the blocks, it is possible to change from flow to static measurement.
-
Product
PathWave BenchVue Advanced Battery Test And Emulation Software For A Single Instrument
BV9211B
-
Achieve higher accuracy, repeatability, and safety with an emulation based on a unique battery model. Your model will allow you to determine your device's power consumption, emulate an actual battery, and import existing battery models.
-
Product
Direct Burial Half Cell Reference Electrode
DB-A
-
Model DB-A Copper-Copper/Sulfate Reference Electrode designed for direct burial for long term monitoring of buried or earth contacting structures.
-
Product
LC/MS/MS Method Package For Cell Culture Profiling Ver. 2
-
This Method Package enables the analysis of 125 compounds in under 20 minutes per sample. Performing analysis separately for each compound group such as amino acids and vitamins makes profiling of cell culture components very laborious, but with this method package a large number of culture medium components and secreted metabolites can be analyzed simultaneously.Compared to the previous version, several metabolites derived from amino acids, nucleic acids and the TCA cycle have been added, allowing even more comprehensive profiling information to be gathered.
-
Product
12V Auto Battery And Charging System Analyzer
1947
-
Peaceful Thriving Enterprise Co Ltd
1. Check for batteries, regulators and alternators. 2. For all 12V system vehicles, with LED indicator that helps pinpoint problems for fast troubleshooting. 3. Other car battery testers are also available.4. With CE Approval.
-
Product
Battery Testing
-
Weshine Electric Manufacturing Co., Ltd
The DC test method is adopted to simulate the actual use of the battery in a real and objective way, which can effectively eliminate the hidden dangers such as deficiency, deficiency and connection failure between batteries while measuring the internal resistance of the battery.
-
Product
Lead-acid Storage Battery Analyzer
-
From the beginning of 2006 the verification of measurements of the analyzer of lead-acid chemical sources developed by Company "Megaron" is spent in Test laboratory "Neva-Reglament". The analyzer is intended for the express-estimation of a condition of lead-acid batteries: before the first use of new battery (an estimation of the electric characteristics declared by the manufacturer); during the battery operation (an estimation of a condition and working capacity at real application).
-
Product
(Automatic Redundant Battery Selector With Source Control And Monitoring)
ARBS 2600
-
La Marche Manufacturing Company
Our product is designed with high powered diodes to select the higher voltage of the two isolated DC power sources. The ARBS selects power from the best available battery while isolating the alternate battery bank. The special heat sink diode assembly is manufactured to handle high output requirements with safety margin to spare.
