-
Product
Single / Dual channel Dual Redundant DDC Controller
PCI-1553DDC-2
Controller
The PCI-1553-DDC-1/2 implements a complete single channel dual-redundant MIL-STD-1553 bus terminal on a half size PCI Card. Full BC/MT/RT modes are supported. 0°C to 70°C operating temperature is standard. Included is an DDC Enhanced ACE intelligent communications protocol engine, dual transceivers and encoder / decoders, shared memory, and management logic.
-
Product
Fixed Gas Detectors
MicroSafe 500 & 600 Series
-
Teledyne Gas & Flame Detection
MicroSafe 500 and 600 Series gas detectors feature a non-intrusive operator interface. Calibration and programming instructions appear in simple intuitive and sequential script on a 16-character backlit display. The transmitter design incorporates extensive fault diagnostics with each condition conveniently identified on the transmitter display.The 500 Series comes standard with a linear 4-20 mA output, one-man remote calibration, self-adjusting zero and span, and LED indicators for fault and calibration status.The 600 Series includes the same features as the 500 with the addition of 3 alarm relays and an RS-485 serial communications port.Electrical Classification - Explosion proofClass I, Div 1, Groups B, C, D
-
Product
Conduction Cooled VPX Interface Board with PCI Express Host Interface
EXC-8000ccVPX
-
The EXC-8000ccVPX is part of the 8000 family of multiprotocol carrier boards. This conduction cooled VPX interface board has a PCI Express host interface and can support up to four independent removable modules and 10 on-board Discrete channels. Each removable module can be any of the 8000 family modules.The EXC-8000ccVPX supports Direct Memory Access (DMA), which enables the board to access system memory for reading and writing independently of the computer’s CPU. This results in faster data transfer to and from the board, with much less CPU overhead than when not using DMA.The EXC-8000ccVPX is supplied with C drivers, including source code. Mating connector provided for I/O connection.
-
Product
sbRIO-9265, Non-Enclosed, 4-Channel C Series Current Output Module
780921-01
Current Input Module
Non-Enclosed, 4-Channel C Series Current Output Module - The sbRIO‑9265 is ideal for interfacing and controlling industrial current-driven actuators at high rates. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The sbRIO‑9265 requires an external power supply and includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity. Non-enclosed modules are designed for OEM applications.
-
Product
Anemometer, 2m/s to 30m/s, 0 °C, 40 °C, 162 mm
72-10455
-
The 72-10455 is an Air Velocity Meter with 9999 display count. It comes with auto record time setup, units switch, LCD backlight, display VEL wind speed display and display FLOW wind count display.
-
Product
SODIMM DDR4 3200MT/s
SQR-SD4S
Dual In-Line Memory Module (DIMM)
Original Hynix IC chips adopted, Data transfer rate: 3200MT/s. Capacity: 4/8/16/32GB, Operating temperature: 0 °C ~ 85 °C Lifetime warranty.
-
Product
Robust DIN-rail Fanless Embedded System With Intel® Celeron® Processor N3350/Pentium® Processor N4200, Isolated COM, LAN And DIO
ICO300-83B
-
The ICO300-83B is powered by the low-power consumption Intel® Celeron processor N3350 (Formerly codename: Apollo Lake). ICO300-83B’s proven rugged construction ensures harsh operating conditions with an extended temperature range of -20°C to 70°C (-40°C to +70°C for option), a wide voltage range of 12V-24V DC power input with overvoltage and reverse protection, and up to 2G vibration endurance. It supports one DDR3L-1866 SO-DIMM slot with up to 8 GB of system memory. Additionally, the ICO300-83B is equipped with two full-size PCI Express Mini Card slots, one for an mSATA storage card and another for 3G/GPRS/Wi-Fi - allowing it to provide flexible communication and data transfer options for use as an IIoT gateway.
-
Product
Transverse and Diametral Extensometers
-
3 models cover most any test requirement and can be used with axial extensometers at the same time. Miniature and standard units, also r-value units. Available options cover temperatures from -265 to +200 C (-450 to +400 F).
-
Product
Digital Infrared Thermometer
IR-710
-
Shenzhen Calibeur Industries Co., Ltd..
'- Non-Contact Infrared Thermometer With Laser Targeting '- Range: -38° C to +520° C/-36.4° F to +968° F'- Accuracy : < 0°C： ±3% or ± 3°C ≥0°C： ±2% or ±2°C'- Distance spot ratio (D:S) : 8:1'- ℃/℉ exchange,'- Size: 180x80x40mm'- Weight: 120g'- Power: AAA1.5V 2pcs (not included)
-
Product
Potentiometer, Level Transmitter, Position Transmitter
Model TWP / TWP2
-
Kusam Electrical Industries Limited
• Aux. Power AC 85 ~ 265V or DC 85 ~ 300V• High Accuracy 0.1% RO at 23 ° C - 5 °C• Input / Output User Selectable• PC Plastic Case, DIN Rail or Wall Mounting• High Dielectric Strength (AC 1.5KV/Min, between Input / Output / Power)
-
Product
pH 5+ Handheld pH Meters
-
These meters are perfect for fast, accurate results. Automatic temperature compensation (ATC) ensures accuracy from 0 to 80°C. Meters include a protective rubber boot that also acts as a meter stand.
-
Product
NI-9232, 3-Channel, 102.4 kS/s/channel, ±30 V, C Series Sound and Vibration Input Module
784397-01
Sound and Vibration
3-Channel, 102.4 kS/s/channel, ±30 V, C Series Sound and Vibration Input Module - The NI‑9232 can measure signals from integrated electronic piezoelectric (IEPE) and non‑IEPE sensors such as accelerometers, tachometers, and proximity probes. The NI‑9232 is also compatible with smart TEDS sensors. The NI‑9232 incorporates software-selectable AC/DC coupling, IEPE open/short detection, and IEPE signal conditioning. The input channels simultaneously measure signals. Each channel also has built-in anti-aliasing filters that automatically adjust to your sample rate. When used with NI software, this module provides processing functionality for condition monitoring such as frequency analysis and order tracking.
-
Product
PXI Multifunction I/O Module
Multifunction I/O
The PXI Multifunction I/O Module provides I/O with varying numbers of channels, sample rates, and output rates with precise timing, triggering, and synchronization between models. This module can be used for industry applications such as laboratory research, design verification test, and manufacturing test.The PXI Multifunction I/O Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
EtherCAT Slave System
EPS Series
-
The ADLINK complete EtherCAT solution, from hardware to middleware to software, with every element tailored for dedicated EtherCAT functionality, includes PCIe-833X Series master controllers, EPS slave systems, and remote monitoring and control providers. As well, ADLINK’s Softmotion one-stop control kernel delivers flexible and easy-to-use intelligent platforms for driving next-generation modern Smart Factories. ADLINK's EPS slave system brings the power the flexibility to EtherCAT environments. State-of-the-art modular construction allows the EtherCAT slave to be configured to fulfill the needs of both small local applications and expansive distributed platforms. The EPS system with comprehensive and high-density I/O modules that include DI/O, pulse-chain motion modules. Leveraging ARM and FPGA technologies, the EPS slave is able to monitor and report system integrity via EtherCAT communication, while relay module lifecycle and signal integrity of analog output are monitored cyclically, and hot swappability reduces downtime significantly. Uniquely designed for full operability in conditions from -20°C to 60°C,the EPS slave system is also fully compliant with the EN 60068-2 standard for shock and vibration and EN 61000-6 for heavy industrial EMC protection, as well as emission certification. Corresponding ESI files for each EPS system can be generated thru ADLINK's Windows-based EtherCAT slave utility, LinkMasterPro™.
-
Product
DC/AC Inverter 1500 W
ODS-1500-7113-T
-
DC/AC inverter with 1500 W from Premium | input ranges 16.8 - 30 VDC | output 230 VAC | operates in temperatures from -25 to +70 °C | approved for EN45545-2 fire and smoke | railway version
-
Product
Microphone Pre-Amp Audio Interfaces
-
Analog Devices mic pre-amp audio interfaces provide a high fidelity, high performance solution for audio products. Specifications for this family include ultralow 1.5 dB noise figures, 140 dB gain range, and high gain capability. Operating in an extended industrial temperature range of –40°C to +85°C, this portfolio of mic pre-amp audio interfaces supports many applications, including precision instrumentation, active filters, low noise amplifier front ends, surveillance systems, computerized voice recognition, and a variety of other industrial and consumer products. As the first choice for serious audio engineers, Analog Devices mic pre-amp audio interfaces can give your applications the performance needed to meet the most demanding specifications.
-
Product
DC/DC Converter 2 W
REM2-153.3D
-
DC/DC converter 2 W from Recom | input ranges 13.5 - 16.5 VDC | outputs +/-3.3 V | operates in ambient temperature from -40 to +95 °C
-
Product
16G R-DDR4-3200 1GX8 1.2V Samsung Chip -40~85C
AQD-D4U16R32-SEW
Memory Module
Registered DIMM, 30u" Gold Plating Thickness, Anti-sulfurization resistance. 1.2V power consumption, Samsung original chip, wide temperatures from -40° to 85°C.
-
Product
HS-1760 Flight Rated XMC Network Interface Controller
XMC-1760-NIC-CC
-
Avionics Interface Technologies
Dual Channel configurations supporting NC/NC, NC/NT, or NT/NT - 75 Ohm single ended copper or 150 Ohm differential - Eight (8) opto-isolated discrete I/O lines - Rear I/O through the P16 connector - Conduction-cooling and/or conformal coating available - x4 PCIe interface to NIC interfaces, with DMA controller for data movement - Designed for extended temperature operations - ANSI Application interface supporting C development - Device driver support: Windows, Linux, & VxWorks (others on request)
-
Product
Microphone Preamplifier
HT426E01
-
Nominal Microphone Diameter1/2Frequency Response Electrical Noise(at 22 C) (Flat 20 Hz to 20 kHz)Distortion (3 V rms input at 1 kHz)<-70 dB<-70 dB[1] EnvironmentalTemperature Range (Operating)-40 to +248 FExcitation Voltage 20 to 32 Constant Current Excitation 2 to 10 mA
-
Product
Fanless Embedded System With 7th Gen Intel® Core™ I7/i5/i3 & Celeron® Processors, Built-in Layer 2 Managed PoE Switch For Railway PC
tBOX400-510-FL
-
The tBOX400-510-FL is a two-in-one transportation-certified box PC with built-in layer 2 managed PoE switch for IP surveillance applications. The tBOX400-510-FL is certified with CE (Class A) and FCC and is in compliance with EN 50155 and EN 45545-2. This high-performance transportation box PC is powered by the 7th generation Intel® Core™ (Kaby Lake) or Intel® Celeron® 3965U processors, along with dual DDR4 SO-DIMM slots for up to 32GB of memory. The built-in 10-port managed switch is powered by Qualcomm's chip. The tBOX400-510-FL has a built-in 10-port managed switch with 8-port 10/100 Mbps PoE and 2-port Gigabit LANs, featuring VLAN, QoS and PoE scheduling for the more secure and smooth network. For reliable operation in severe environments, the rugged fanless transportation box computer is designed to withstand a wide temperature range from -40°C to +60°C and vibration of up to 3 Grms. It also supports a wide voltage input range: 9V to 36V DC for vehicle applications, 14V to 32V DC for marine applications, and 24V to 110V DC for railway applications. With its high performance, industrial-grade design and full-strict certifications, the tBOX400-510-FL is suited for transportation-related applications such as onboard video surveillance and video management.
-
Product
Ethernet Parallel Interface
Model 8013
-
* Provides 128 high-power TTL I/O lines.* Fully VXI-11 Compliant plus Raw Socket for easy programming with Visual Basic or C, Agilent VEE and LabVIEW.* Standard board has a horizontal Ethernet connector and 150-pin Digital IO connector on the component side. * Mates to Relay Driver Boards with 64 or 128 Relay Drivers.* Mates to 115650 Connector Board with 4 flat ribbon headers.
-
Product
10-Zone SMT Reflow Oven
CR10000
-
10 fully controlled upper and lower convection heating zones allow the CR10000 SMT reflow oven to provide you with a thermal accuracy of ±1˚C. Manncorp’s low-velocity, low-turbulence air flow options produce an even ΔT of ±2°C across PCB assemblies out to 22” (570 mm) wide edge-to-edge backed by throughput that can still keep pace with your high-volume production needs.
-
Product
CSvideo | CTvideo | CSvision Series Infrared Thermometer
-
The video pyrometer series optris CSvideo/CTvideo and the new innovative ratio pyrometer CSvision allow a parallel use of video and crosshair laser aiming for an optimal measuring field adjustment even in processes with limited access. They reliably measure temperatures of metals or ceramics and, due to their short measuring wavelength, reduces measuring errors of surfaces with low or unknown emissivities. The high quality video sighting can show its full advantage together with the software CompactPlus Connect or the IRmobile App on your cell phone with state-of-the-art zoom and image rotation features. The adjustable focus, motorized on CSvision, allows an optimal adaptation to different application and installation demands. As CSvision can measure objects up to 3000 °C a unique two-step brightness reduction filter (BRF) is giving the user a tremendous advantage when aiming on hot and extremely bright objects.
-
Product
PXI SPDT Switch: 64-ch, 100 Vrms / 1A, Reed Relays
M9131A
Switch Module
The M9131A is a high-density, general purpose switch with 64 independent, single-pole, double-throw (Form C) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights, or actuate external power relays and solenoids. The high-speed, long-life reed relays can handle 100 Vrms and 1 A, with up to 3 W maximum power. Choose from the durable connector block or standard cable connections.
-
Product
Temperature Input Device
-
The Temperature Input Device is a thermocouple measurement device featuring InstantDAQ technology. InstantDAQ technology includes built-in software for viewing and logging data that automatically loads when you plug in the device, so you can instantly take temperature measurements with your PC. You can connect the Temperature Input Device to any USB port to use your PC as a display and monitor data in real time. The device is compatible with J, K, R, S, T, N, E, and B thermocouples.The Temperature Input Device includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
sbRIO-9482, Non-Enclosed, 4-Channel, SPST Relay, 60 VDC (1 A)/250 VAC (1.5 A) C Series Relay Output Module
783000-01
Relay Output Module
The sbRIO‑9482 directly connects to a wide array of industrial devices such as motors, actuators, and DC devices. Each channel provides access to an electromechanical relay for switching signals up to 60 VDC (1 A) or 250 Vrms (1.5 A), features channel‑to‑channel isolation, and has a LED that indicates the status. Non-enclosed modules are designed for OEM applications.
-
Product
Manual Step Attenuator, DC to 4 GHz, 0 to 11 dB, 1 dB steps
8494A
Attenuator
The Keysight 8494A, dc to 4 GHz manual step attenuator, offers exceptional repeatability and reliability. Attenuation is provided in 1 dB steps from 0 to 11 dB. Precision gold-plated leaf springs ensure long-life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
-
Product
Radar solution for width measurement of steel & metal
-
The OndoSense radar sensor solution determines the width of steel plates, steel strips or steel slabs (up to 1600 °C hot) with an accuracy of up to ±300 µm. Thanks to robust radar technology, sophisticated signal processing and smart radar algorithms, our radar sensors offer this high precision in width measurement even in the extreme production environments of the metal and steel industry.
-
Product
C/Ku Band Satellite Monitoring
SCL-3412
-
C/Ku Satellite Monitoring System (SCL-3412) is designed to intercept International/national telecom carriers, GSM A/Abis links and IP Carriers over satellite which are using C, Ku, X or Ka-Band. In order to reduce the manual effort and time consumed in the analysis of the carriers, system is integrated with Satellite Carrier Analysis module, which automatically performs the scanning on the selected spectrum and provide the list of carriers along with their payload type (i.e DCME, GSM or IP) and characteristics parameters. This provides great help to take decision for monitoring of the carriers of interest.
