Digital TV
Telecommunications system where transient image and sound are broadcast and received through the use of digital signal.
-
Product
Digital Input Board
VME-1150B
Digital Input Board
64-bit Optically Coupled Digital Input Board
-
Product
Synchro to Digital-Resolver to Digital Converters
Synchro- Burst
Digital / Synchro Converter
Computer Conversions Corporation
Computer Conversions Corporation's Synchro-Burst is a complete 2 channel Synchro to encoder interface designed to easily integrate inherently absolute rotary synchro, resolver or linear LVDT position sensors into motion controls and counters that are normally only designed to facilitate incremental encoder feedback.
-
Product
Digital Input Board
VME-1129
Digital Input Board
VME-1129 128-bit high voltage digital input board with Built-in-Test and input filter. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297), with the following mnemonics: A24:A16: D32/D16/D08 (EO): Slave:39/3D: 29/2D Form Factor: 6U
-
Product
PCI-6512, 64-Channel, ±30 VDC, Source Outputs, Bank-Isolated Digital I/O Device
778968-01
Digital I/O
The PCI-6512 is an industrial digital output interface, with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6512 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Digital Synchro and Digital to Resolver
DSL- DRL
Digital / Synchro Converter
Computer Conversions Corporation
The DSL - DRL Series are highly reliable, miniature, low profile and low cost, continuously updating Digital Synchro and Digital to Resolver (AC Sine / Cosine) Converters designed for military and industrial control applications.
-
Product
Dynamically Controlled, High Voltage Digital I/O PXI Card With Pin Electronics
GX5055
Digital I/O
The GX5055 represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the GX5050, the GX5055 offers high performance pin electronics and an enhanced timing generator in a compact, 6U PXI form factor.
-
Product
48 Optocoupled Digital Inputs
YAV90321
Digital I/O
Input Voltage 3…42Vdc Isolated Inputs / Control >1000Vdc CAN Control (or Ethernet with Ethernet to CAN Gateway.) Drivers dll & VIs available.
-
Product
Handheld Digital Multimeter, 4.5-digit, with Organic LED Display (OLED)
U1253B
Digital Multimeter
The Keysight U1253B 4.5-digit handheld digital multimeter (DMM) is feature-packed to simplify the troubleshooting of electronics and electrical circuits indoors, on the bench or in the field. Key capabilities include its organic LED (OLED) display that provides razor-sharp readings even in dark, off-angle situations. The U1253B is the world's first OLED handheld DMM of its kind. For those long, continuous measurements, the DMM equips you with the easy-to-use GUI data-logging software to automate virtually unlimited data recordings to PC. The U1253B comes with an integrated 20 MHz frequency counter for high frequency measurements, and a built-in programmable square-wave generator with selectable frequency and duty cycle. With the versatile U1253B, you are well equipped to perform thorough troubleshooting of any faulty circuit.A multi-award winner
-
Product
NI-6581, 100 MHz, 54 Single-Ended-Channel Digital I/O Adapter Module
780565-01
Digital I/O Adapter
100 MHz, 54 Single-Ended-Channel Digital I/O Adapter Module for FlexRIO—The NI-6581 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a digital instrument for interfacing with 54 single-ended digital pins. You can use the NI-6581 to do real-time interfacing of standard protocols and implement customized protocols. The NI-6581 can operate sample digital waveforms at up to 100 MHz. It includes support for common transistor-to-transistor logic (TTL) voltage levels, or other voltage references can be sourced externally using a front panel connector.
-
Product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5280 Series
Digital I/O
The GX5280 Series are high performance, cost-effective 3U PXI dynamic digital I/O boards with 32 TTL input or output channels and 32 LVDS input or output channels. The GX5280 Series offers an industry leading 512 MB of on-board memory and supports test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Product
Ethernet/LXI digitizerNETBOX 14 Bit High Speed Digitizer - 400 MS/s on 16 Channels, 16 Single-Ended Inputs
DN6.448-16
Digitizer
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
PXI 32 Chan I/O Parallel I/P Prog Threshold
40-412-101
Digital I/O
A 32-channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel. The module is available in two versions with either serial or parallel capture of the input levels.
-
Product
PXIe-6569, PXI FlexRIO Digital I/O Module (64-in LVDS, 8 SE, KU060)
787282-01
Digital I/O
1.25 Gbit/s, Kintex Ultrascale FPGA, 64 LVDS Channel FlexRIO Digital I/O Module - The PXIe-6569 provides a digital I/O interface along with a user-programmable FPGA for flexibility to fit a variety of interfacing and application needs. This module can interface with up to 64 … single-direction low-voltage differential signal (LVDS) channels and eight bidirectional single-ended channels. You can use the PXIe-6569 for real-time interfacing of standard protocols or implementing customized protocols.
-
Product
PXIe-5763, 16-Bit, 500 MS/s, 4-Channel PXI FlexRIO Digitizer
785163-01
FlexRio Digitizer
The PXIe-5763 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PXIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
Transcoding Card
VEGA-3310
Digital Input PCIe Card
2-ch 4Kp60 or 8-ch real-time 4:2:2 10bit HEVC,AVC & MPEG-2 encode, decode & transcodeUltra-low latency supportLess than 35W power consumptionSimple-to-use API and example code for FFmpeg and GStreamer multimedia frameworks
-
Product
PCIe-5764, 16-Bit, 1 GS/s, 4-Channel PCI FlexRIO Digitizer Device
785960-01
FlexRio Digitizer
The PCIe-5764 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PCIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer.
-
Product
4-CH 12-Bit 80 MS/s PCI Express Digitizer
PCIe-9814
Digitizer
The ADLINK PCIe-9814 is a PCI Express digitizer providing speedy, high quality data acquisition. Each of the four input channels supports up to 80MS/s sampling, with 12-bit resolution A/D converter. This allows simultaneous recording of signals on all channels with no inter channel phase delay. The extremely large on-board memory enables long recording times even at the highest sampling rates.Unlike parallel PCI buses, PCI Express slots utilize serial point-to-point connection. Each connection pair (lane) can achieve burst connection speeds of 250MB/s. The PCIe-9814, based on x4 lane slot PCI Express technology, provides a clear advantage in that direct connection of each slot allows full transfer bandwidth for each individual card. The ADLINK PCIe-9814 x4 digitizer can be used in any standard PCI Express slot, x4, x8, or x16.
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 2.5 GS/s on 4 Channels, 1.5 GHz Bandwidth
DN2.222-04
Digitizer
The digitizerNETBOX DN2.22x series allows recording of up to 8 channels with sampling rates of 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
sbRIO-9375, Non-Enclosed, 24 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781212-01
Digital Module
Non-Enclosed, 24 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The sbRIO‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The sbRIO‑9375 offers isolation between the input and output banks from channel‑to‑earth ground. Non-enclosed modules are designed for OEM applications.
-
Product
64 Output USB Modular Digital I/O
U2653A
Digital I/O Module
The Keysight U2653A USB Digital I/O is a cost-effective device with its offering of 64 opto-isolated digital lines. It comes bundled with the Keysight Measurement Manager (AMM) software for quick set up and data logging. Simplifying this further is the command logger function offered in the Keysight Measurement Manager that allows capturing of configuration commands that can be easily converted to snippets of VEE code. Other supported languages are VB, C++, and C#.
-
Product
33/60 GHz Dual Electrical Channel Module
N1040A
Digital Input Module
The N1040A is a dual electrical channel plug-in module for the N1000A DCA-X mainframe and provides two electrical channels with maximum bandwidth of 33 or 60 GHz, based on the option selected.
-
Product
Synchro to Digital-Resolver to Digital Converters
SDC-RDC 20
Digital / Synchro Converter
Computer Conversions Corporation
SDC & RDC 20 BIT Synchro / Resolver to Digital Converter
-
Product
PXIe-7822, PXI Express Digital RIO with Kintex-7 325T FPGA
783486-01
Digital I/O
Kintex 7 325T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module—The PXIe‑7822 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PXIe‑7822 supports peer‑to‑peer streaming for direct data transfer between PXI Express modules. The PXIe‑7822 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
Product
PCIe-4065, PCI Express, 6½-Digit, ±300 V Digital Multimeter Device
779771-01
Digital Multimeter
The PCIe‑4065 makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
Product
Digital multimeter, 6 digit
34461A
Digital Multimeter
Color, graphical display with built-in bar chart, histogram, trend, math, and statisticsI/O: USB, LAN/LXI, GPIB (optional)BenchVue software enabled: Do more with your PC and instrument together, no programming required. Easily control your DMM, quickly build automated tests, log measurements and save precious time.
-
Product
PXIe Isolated Digitizer, 2-channels, 16-bit, 256 V, 32 Msa/Ch memory
M9217A
Digitizer
The M9217A PXIe digitizer is a single slot, 2 isolated input channels, supporting up to 256 V and sampling rate of 20 MSa/s and 16-bit resolution.
-
Product
12DI/6DO IoT Modbus/SNMP/MQTT Ethernet Remote I/O
ADAM-6050
Isolated Digital I/O Module
12ch digital input(counter)/6ch digital output(pulse output)Protocols:MQTT(TLS),SNMP,Modbus TCP,RESTful API,ASCIIGCL to perform basic logic control rulesPeer-to-Peer function to map I/O statusCloud access: Data update to AzureBuilt-in web serverWatchdog timer to recover the system
-
Product
NI-9425, 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module
785044-01
Digital Module
24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module - The NI‑9425 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels. The NI‑9425 offers isolation between the input and output banks from channel to earth ground. You cannot use the NI‑9425 in a CompactDAQ chassis to perform counter operations.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 250 MS/s on 2 Channels, 2 Single-Ended Inputs
DN2.442-02
Digitizer
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
Ethernet/LXI digitizerNETBOX 16-Bit Multi-purpose Digitizer - 5 MS/s on 32 Channels
DN6.591-32
Digitizer
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
