-
Product
CEMS II E Continuous Emission Monitoring System
-
CEMS II e takes away the manual configuration and settings adjustments from your day-to-day emissions measurements. A fully automated continuous emission monitoring system CEMS II e is TÜV and MCERTS certified solution (QAL1) to offer environmental compliance. This emission monitoring system is suitable for measuring pollutants continuously from hot, wet and corrosive gas streams in various industrial processes, such as powerplants, waste incineration, cement plants and beyond.
-
Product
QoS Monitor
Arptel Monit
-
The Arptel Monit is a cost-effective and flexible network monitor solution for telcos. The Arptel Monit is a powerful tool for monitor QoS on live international and domestic traffic.
-
Product
Ground Fault Monitors
IFT
-
In most industrial settings, ground faults can cause significant damage. Since these leaks are unavoidable in almost all industrial environments, our ground fault monitors allow you to quickly and easily find the source of the leak before a major problem occurs and damages your equipment. The IFT-120 is designed to help you rapidly locate ground faults.
-
Product
Fixed Area Hydrogen Monitor
HY-ALERTA™ 600B
-
H2scan’s HY-ALERTA™ 600B Fixed Area Hydrogen Monitor will provide hydrogen-specific leak detection and measurement for hydrogen concentrations as low as 4000 ppm and can be scaled to any concentration up to 5% hydrogen by volume, a range representing 10% to 125% of hydrogen’s low flammability limit. They are designed for either ceiling or wall mount and have RS422 capability that extends the interface from the sensor to the controller to several hundred feet. H2scan’s hydrogen-specific sensor technology has no cross sensitivity to any other combustible gases, thus eliminating false positive alarms and increasing system reliability.
-
Product
Condition Monitoring
-
Our condition monitoring products provide you with the essential data needed to prevent unplanned downtime before it costs you. Real-time monitoring of the health and condition of your machines enables smart manufacturing. This allows you to predict and protect against potential equipment failures before they have a chance to impact quality and maintenance costs.
-
Product
SafeOne RF Safety Monitor
-
The SafeOne is a RF Safety Monitor covering the requirements set forth in WHO ICNIRP specifications. It has a very wide frequency range covering 30MHz to 10GHz, which makes it suitable for use in almost all antenna installations. Due to the innovative lightweight design, technicians can wear this at all times, without the need to constantly be observant of the state of the instrument. The SafeOne is powered with standard batteries, with 250 days of continuous operation.
-
Product
Real-Time Video/Audio quality monitoring
VQEmbed
-
VQEmbed libraries provide real-time video/audio quality monitoring for OEMs wanting to offer a fully automated Quality of Service monitoring solution to their customers.
-
Product
Free Bandwidth Monitoring & Usage Reporting
NetWorx
-
NetWorx is a simple and free, yet powerful tool that helps you objectively evaluate your bandwidth situation. You can use it to collect bandwidth usage data and measure the speed of your Internet or any other network connection.
-
Product
Fume Hood Monitor
FHM10
-
Fume hoods are a primary source or protection in laboratories. Face velocity measurements are often used to gauge the performance of a fume hood’s ability to contain and exhaust hazardous chemicals. By accurately measuring face velocity and alarming on unsafe conditions, TSI’s FHM10 Fume Hood Monitors provide a high level of fume hood safety. And, the FHM10 helps users comply with standards and regulations set forth by OSHA, NFPA, ANSI Z9.5, and SEFA, calling for monitors to be installed on fume hoods.
-
Product
Engine Health And Vibration Monitoring
-
Engine Health and Vibration Monitoring systems provide the data required to support condition-based maintenance and “power-by- the-hour” commercial frameworks. They can also tell the pilot or maintenance crew if the engine rotors are out of balance (a mandatory requirement for passenger-carrying jet-powered civil aircraft).
-
Product
Monitoring & Drive Test Antennas
-
Linear polarized half-wave dipole with 1:1 balun and fixed element length for fieldstrength measurements at TETRA (terrestrical trunked radio) networks.
-
Product
Power Monitoring Kit For SAR System Validation
PMK
-
Test labs have a daily requirement to ensure SAR measurements are highly accurate. SAR systems must be vigorously checked to ensure the measuring accuracy meets the system manufacturer uncertainty budget. The PMK features technologies usually found in more expensive equipment at an affordable price. The ability to measure the S11 parameter for dipoles and antennas while continuously monitoring their linear behaviour differentiates the PMK from other systems. The ART-Fi PMK is an all-in-one solution that requires only three connections to perform automatic, highly precise validations and verifications. The lack of moving parts also leads to improved durability and fewer bugs, faults, and workarounds.
-
Product
Multi SDI Monitor
LV 5381
-
The LV 5381 is a waveform monitor that can monitor up to four SDI signals simultaneously.It is optimized for the level adjustment of the outputs of multiple installed cameras. In the video signal waveform display, vector display, and picture display, multiple input signals can be displayed on top of each other or lined up next to each other.It is also full of useful features such as a level meter display for embedded audio, an error display that indicates transmission errors, and a 5-bar display that shows video signal peak levels using five bars. Furthermore, the LV 5381 can show different combinations of these displays in its multi-screen display.
-
Product
Clamp type AC Current Sensor／for Power Monitor
ZCT-40PS
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 1A～500A*Current measurements of feeder
-
Product
Condition Monitoring System
-
Cut costs and boost productivity with a condition-monitoring tool designed for ease of use and scalability. The Dynapar OnSite™ system is a powerful predictive maintenance system targeted at preventing failures before they occur. It can slash unscheduled downtime, improve efficiency of route-based vibration analysis, and provide real-time analytics and trending to warn of possible machine failures.
-
Product
Clamp type AC Current Sensor／for Power Monitor
ZCT-23S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Ultra compact size*AC 0.1A～120A*Current measurements of terminal feeder
-
Product
Environmental Radiation Monitoring Systems
-
With the autonomous radiation monitoring probe GammaTRACER, the gamma radiation dose is continually registered in the chosen time sequence. Energy-saving chip technology allows maintenance-free non-stop operation of the GammaTRACER probe of typically five years, with extended battery pack up to ten years! Hermetically sealed, it is designed to endure the harshest environments.
-
Product
MOD MONITOR
TYPE HFX-1
-
The Type HFX-1 Modulation Monitor is an ancillary piece of equipment, which is used with narrow bandwidth, or older oscilloscopes to allow viewing of RF signals and particularly modulated signals as high as 55MHz. The equipment contains an RF signal source and a broadband mixing circuit which converts the high frequency signal to an intermediate frequency within the oscilloscope’s range. The frequency control dial is simply adjusted until the RF signal is viewed on the scope. BNC connectors are mounted on the rear panel to allow interconnect to the scope and RF probe. This product was previously called "oscilloscope frequency extender" and may be used to view other high frequency signals on older or narrow band scopes.
-
Product
Process And Chamber Monitoring Software & Systems
-
MKS process and monitoring solutions feature real-time, web-enabled, hardware, software, and systems to support a variety of tools and processes. These solutions improve performance and yield while reducing tool damage and false alarms.
-
Product
Measuring & Monitoring Relays
-
Fixed or adjustable threshold for low level or high level voltage or current monitoring.
-
Product
Environmental Noise Monitoring System
E-Box LITE
-
When you need to perform unattended noise measurements that are to be left outdoors, the very last thing you need is the hassle of complicated equipment.
-
Product
Digital RF Power Monitor
3024
-
The COMM-connect 3024 RF Power Monitor from LBA Technology can control up to 8 external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. The Power conversion algorithms handles multi carrier, multi mode, peak, average and RMS signals. The power readout is auto scaled and VSWR can be calculated between any probes. Also the measured and calculated results along with alarms can be shown in the local LCD. The instrument has SNMP support to allow network management. The instrument can be configured for VSWR and Power limits to give alarms. The alarms can be configured to operate relay drivers or isolated Optcouplers. The alarms can also be configured as SNMP traps sending relevant information to the network control center. The COMM-connect 3024 WEB enabled RF Power Monitor gives an unlimited number of applications to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
Product
Ohm-Stat Guardian Pro Constant Monitor
-
Tests two people and two wriststrapsLED and buzzerNIST calibration includedWorks with all single wire capacitance wrist strapsAll cords suppliedCE markCan be calibratedProduct conforms to the ESD S.20.20 spec standards110v AC powerGround dock included
-
Product
Mainframe Performance Monitoring & Analysis
Strobe
-
Compuware Strobe is the industry-leading application performance monitoring and analysis solution for mainframe applications. With Strobe, IT departments can pinpoint application inefficiencies that cause excessive CPU consumption and reduce hardware and software costs while increasing customer satisfaction.
-
Product
Vault Gas Monitor
SMC 2400
-
The SMC 2400 Vault Gas Monitor detects combustible and carbon monoxide gas leaks to reduce the hazard of gas explosion and to maintain personnel safety. The monitor offers the gas detection functions required by telecom site managers including uninterrupted power supply, long-life sensors, five alarm relays, and both audible and visual alarm indication.
-
Product
Stationary Sonaphone For Online Monitoring Of Processes And Machines
SONAPHONE® S-SB10.xx
-
With the Stationary SONAPHONE S-SB10.xx and its associated probes machine and plant processes can be monitored permanently, insofar as a detectable ultrasonic level is generated. A fixed installation at an inspection point enables trend monitoring for longer periods. Based on changes of the ultrasonic sound level the assessment of plant condition is possible. Different probe versions support airborne sound and structure-borne sound applications.
-
Product
Combo Gas Monitor
Z-Gard Combo Gas Monitor
-
A cost-efficient monitor for underground garages and ventilation control, the Z-Gard Combo Gas Monitor uses an electrochemical sensor to detect carbon monoxide. The unit features local audio/visual alarm status indicators and it can be configured to interface with air-handling equipment to control air quality within a building.
-
Product
Social Distancing Monitor
Aura
-
The Aura personal proximity sensor is designed to tackle the challenge of social distancing brought about by COVID-19. It allows businesses to ensure a minimum distance between workers and customers with a lightweight, wrist unit.
-
Product
MultiStandard Advanced Monitoring Probe
EdgeProbe Advanced MultiStandard
-
The ideal tool for accurate & cost-effective monitoring probe for:DTV terrestrial transmission (DVB-T/T2, ISDB-T/Tb)DTV cable transmission (DVB-C/C2)DTV distribution over satellite (DVB-S/S2, T2-MI, OneBeam, MPTS)DTH uplink and reception (DVB-S/S2, MPTS)Digital Radio transmission (DAB/DAB+/T-DMB)Combine any two RF standards in one single 1RU device.Combined with a Network Monitoring System or not, the EdgeProbe Advanced provides a powerful broadcast network alert & diagnosis tool allowing Digital TV & Radio network operators to monitor global trends and anticipate potential failures.EdgeProbe Advanced is able to monitor the RF signal, through its RF inputs (up to 4 in 1RU), as well as the baseband transport before modulator, through its ASI and IP inputs.
-
Product
Advanced Monitoring Probe
DVB-S/S2
-
Combined with a Network Monitoring System or not, the EdgeProbe Advanced provides a powerful broadcast network alert & diagnosis tool allowing DTV network operators to monitor global trends and anticipate potential failures.EdgeProbe Advanced is able to monitor DVB-S and DVB-S2 signals before uplink and after downlink, through its RF inputs (up to 4 in 1RU), as well as baseband transport before satellite modulator and after IRD, through its ASI and IP inputs.
