Telephone Test Set
See Also: Telephone
-
Product
BSD (Test Diagnostics)
test
BSD Test Diagnostics software can be added to either developer or factory run-time systems to further improve the location of faults such as net bridges (short-circuits), open pins, open nets and even ''twisted'' connections that can occur within cable assemblies. BSD Test diagnostics reports faults in a verbose English language statement with pin level information included and can easily interpret multiple fault conditions.
-
Product
Protection Test Set
CMC 850
-
The CMC 850 is a protection test set dedicated to IEC 61850. It focuses on the real-time communication methods GOOSE and Sampled Values to interface with the devices under test.
-
Product
Semi-Rigid Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131C
Test Port Cable
The Keysight 85131C is an 81 cm (32 in) long1 semi-rigid cable with a 3.5 mm female2-to-PSC-3.5 mm female connector. Cable frequency range is DC to 26.5 GHz with a return loss of 17 dB or better. Insertion loss is 0.43 * sqrt(f) + 0.3, where f is frequency in gigahertz, for the test port connector and 2.5 dB at maximum frequency for the device connector. Phase stability of the semi-rigid / flexible cables is specified with a 90-degree bend using a 4 to 3-inch radius. Stability1 of the 85131C is less than 0.06 dB, and phase is 0.16 * f + 0.5, where f is frequency in gigahertz.
-
Product
CDMA2k Analysis Using NI PXI RF Test Instruments
NI-RFmx CDMA2k
Test Instrument
NI-RFmx CDMA2k is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development effort.
-
Product
Hybrid Single Site Test Handler
3110
Test Handler
Chroma Hybrid Single Site Test Handler 3110 is a full range ATC (Active Thermal Control) test handler capable of handling device bodies up to 120x120mm with 450kg force load.
-
-
Product
Regenerative Battery Pack Test System
17020E
Test System
Charge/discharge modes (CC, CV, CP)Power Range: 10kW / 20kW per channelVoltage Range: 60V/ 100VCurrent Range: 100A/200A/300A/400A/ 500A/600A/700A/800A per channelRegenerative battery energy discharge, efficiency 85%Channels paralleled for higher currentsDriving cycle simulationFast current conversion without current interruptHigh precision measurementSmooth current without over shootTest data analysis functionData recovery protection (after power failure)Independent protection of multi-channel
-
Product
High Voltage Impulse Test Set Up
-
We are renowned as the foremost manufacturer and exporter of High Voltage Impulse Test Set Up. This testing equipment is demanded in electrical, power generation and engineering sector. It is incorporated with fiber optic isolated digitizers to test various types of transformers. We utilize excellent grade raw materials to engineer and develop this High Voltage Impulse Test Set Up in accordance with industry standards. Our clients can get this equipment from us at competitive price.
-
Product
Electrification Testing Solutions
Test System
When looking for a partner to assist with your electrification testing or power electronics testing challenge, Ball Systems has the expertise and experience to ensure your energy storage or power conversion project moves forward efficiently.
-
Product
PRO Test Set
TS® 52
-
Fluke Networks’ new TS52 PRO Test Set features the latest in test set technology. Designed with a superior, radiant liquid crystal display (LCD) user interface, it allows you to see what cannot be heard in any outside plant environment.
-
Product
Automatic Test System
Test System
Automatic Test system is the ultimate solution for power electronic testing. The system includes a wide range of hardware choice such as AC/DC Sources, Electronic Loads, DMM, Oscillate Scope, Noise Analyzer and Short /OVP Tester. This flexibility combined with its open architecture software platform-PowerPro III, gives users a flexible, powerful and cost effective test system for almost all types of power supply testing.
-
Product
Loss Test Set, Return Loss Test Set
LTS1315, LTS1315R
-
The KD Optics LTS1315 is a combined mains / battery powered laser source and power meter designed to make attenuation testing in the field easy, reliable and most importantly, consistent. The LTS1315R incorporates return loss measurement (RLM) capability with the ability to switch very easily between dBrel and return loss.
-
Product
Test Lead Set
34138A
Accessory Kit
The Keysight 34138A test lead set for digital multimeters contains fixed sheath banana plugs. The Keysight 34138A is compatible with the 34460A, 34461A, 34401A, 34405A, 34410A, 34411A, L4411A, and U2741A digital multimeters. 34138a is not compatible with 3458A instead use 34137A with 3458A.
-
Product
Longbow Launcher / LEA Test Set
TS-201B
-
The TS-201 is a state-of-the-art I-Level and Depot level test set for MIL-STD-1760 and legacy armament systems including launchers and bomb racks.
-
Product
Combined High Voltage Test Set
-
is extensively used to measure AC and DC voltage of different electrical devices.
-
Product
HV Test System up to 20000 Volt
Test System
Insulated test booth with large space for test items. 2 banana sockets for AC connection and 4 banana sockets for the DC connection of the DUTs. IC’s are tested in a long-term test. These are checked in an oil bath so that there are no air gaps to reduce the insulation. Maximum voltage 20 kV. Therefore, insulation tests must be carried out. Ensuring the standard-compliant test. For the safety of the operating personnel, the test cell is electrically locked while the high voltage measurement is active.
-
Product
LAN/Ethernet/Telephone Cable Tracker & Tester
PHCT65
-
Trace Telephone Wire and LAN CableTrace Wires In Electrical SystemVerify LAN Cable ConditionContinuity TestDC Voltage ProbeBright White LED FlashlightSold as : Unit
-
Product
Dual Telephone Line Tester
NT-6006
-
This tool is for testing the condition of dual telephone line jacks. Multicolor LED indicator light alerts to okay line, reversed line, AC Voltage present and dead line. Fits in shirt pocket.
-
Product
Secondary Injection Test Set
PTE-100-C Plus
-
In the Pro version this voltage source incorporates a dedicated LCD display and its own BUS-PTE connection that make the operation easier and enable it to be used also with other sets in the PTE range.
-
Product
Protection Relay Test Set
PW41i
-
PW41i is designed with 3 currents (3*40A) and 4 voltages (4*300V). The local software system with many relay testing modules is designed based on Windows system, which is easy and convenient for operation and upgrade.
-
Product
PXI Semiconductor/IC Test System
Test System
A high-density 100MHz PXIe digital IO card designed for characterizing, validating, and testing a variety of digital and mixed-signal ICs. Each IO card consists of a Sequencer Pattern Generator (SQPG) and 32 channels of full ATE-like features. The 33010 IO card is expandable up to 256 channels. Some unique features of the 33010 include an on-board SQPG, per pin timing/levels/ PMU/TFMU, multiple time domains, and multithreaded testing for complex IC testing. Each channel is also equipped with 64M vector memory, 16 timing sets with on-the-fly timing change, and per pin timing and frequency measurements up to 400 MHz.
-
Product
Communications Test System for Frontline Diagnostics
CTS-2750
Test System
The CTS-2750 is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The field-upgradeable, software-defined architecture features easy-to-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets can be created easily using the included TestEZ® software suite.
-
Product
Mobile, Hardened Test Set
MBX1
-
With the MBX1 platform and our software, you can easily test SCADA and substation automation systems (SAS) in a highly secure way. The mobile solution allows you to perform quick assessments and temporary monitoring, e.g. during commissioning.
-
Product
Combination Board Functional Test System
QT 4256 ATE
Functional Test
Qmax Test Technologies Pvt. Ltd.
QT 4256 ATE is a combination Board Functional Test System , a main frame Automated Test Equipment (ATE) which can be configured up to maximum of 1280 Bi-directional digital channels ideal for testing circuit card assemblies of high level of complexity and whether it is a legacy or new generation PCB.
-
Product
EBIRST 50-pin D-type To 25-pin D-type Adapter
93-005-414
Test Adapter
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Universal Test Set
UTS
-
The Universal Test Set (UTS) is a portable, battery-powered, programmable, ruggedized radio frequency test set designed to validate improvised explosive device (IED) jamming equipment. Our unit is intended to provide an in-field confidence testing for warfighters employing IED jammers prior to departure.
-
Product
Isolated Digital I/O 60VDC, 150mA
OTP2 module no.186
Test Platform
The National Instruments PXI-6528, PCI-6528, and PXI-6529 Digital I/O Modules are isolated digital I/O interfaces for PCI and PXI. These modules can use inputs from NI 6528 and PXI 6529 devices to capture the status of sensors, actuators, and logic devices. NI 6528 devices have 24 SSR outputs for switching external devices with input currents up to 150 mA. The NI 6528 and PXI-6529 devices are suitable for a variety of applications, from automotive development and industrial factory automation to aerospace, laboratory research, and biomedical applications due to their high current handling capacity and isolation.
-
Product
Current Transformer Field Test Set
1043
-
The Catalog 1043 Current Transformer Field Test Set is a simple and inexpensive means whereby a current transformer installation may be quickly checked for many sources of trouble. The tests are made without interrupting the Customer's service and while the load is on.
-
Product
NI Automated Test Software Suite
test
The NI Automated Test Software Suite features all three NI IDEs and NI's most popular application software and add-ons specifically for building your automated test system with confidence. This package offers the power of LabVIEW, LabWindows/CVI, and Measurement Studio combined with the TestStand ready-to-run, test executive and the Switch Executive intelligent switch management application
-
Product
Advanced Three Phase Automatic Relay Test Sets
MP 3000 Series
-
Advanced three phase automatic relay test set. PC control through user friendly MPWIN Relay Test Software. High accuracy and high power over wide range. Suitable for IEC61850 GOOSE simulation, subscription and sampled value publishing. CE, FCC.
