Inductor Test
-
Product
Test Hardware
TTPSimulate XMC/PCIe
-
TTPSimulate is a high-performance test system which enables the simulation of a networked TTP system in real-time. It allows full hardware in the loop verification of a TTP unit. There are two form factors available for this product – PCIe and XMC card format. Both cards can act as four independent TTP nodes and have an IRIG-B interface for time-stamping.
-
Product
Massively Parallel Parametric Test System
P9001A
In-Circuit Test System
The highest throughput parallel parametric test solution. 100-pin parallel measurement capability and faster single parameter measurement than Keysight 4080. Good data correlation with Keysight 4080. New per-pin parametric test unit module with all basic measurement function (voltage, current, capacitance, pulse, frequency). Easy development of parallel test plan. Easy migration from 4080 environment. Proven in 1st-tier logic foundries and memory companies.
-
Product
Test System
LB302
-
Computer Gesteuerte Systeme GmbH
The LB302 test system is the most used midsize range version of the LB-300 series. It is designed for development as well as for production. The ‘device under test’ (DUT) is connected with a G12 receiver (Virginia Panel Company), which has a high number of possible contacting and a low transition resistance.
-
Product
Power-Switching Test System
High Voltage Switching Test System
-
The Accel-RF Power-Switching Test System is capable of measuring reliability under a variety of conditions for switching power applications up to 1kV (off) and 25A (on) at rates up to 1MHz switching frequency, dependent on voltage. By leveraging technology developed for the RF burn-in tray platform with new fast switching measurement techniques, this system can support testing of multiple devices under elevated temperature stimulus in a small physical area, and offers the flexibility to test both soft- and hard-switching applications. The Accel-RF Power-Switching System is the most flexible and accurate power switching platform available.
-
Product
Motor Testing Panel
VMTP
-
It covers No Load Test, Full Load Test, Block Rotor Test, Temperature Rise Test, Reduce Voltage Test, Pull Up Test, Momentary Over load Test for 3-Phase & 1-Phase Motor. It measures Voltage, Current, Power, Apparent Power, Reactive Power, Power Factor (PF), Frequency, RPM, Corrected RPM, %Slip, Torque with correction, Output Power, Efficiency of Motor.
-
Product
Test Set
TS® 22
-
The TS22 Test Set’s unique built-in one-way amplified speaker provides three audio levels for hands-free listening and use with automated voice response systems. Multiple memories enable storage of nine 18 digit telephone numbers in repertory dialer (speed dialing) for easy access to test boards, the central office and other frequently called numbers. The last number redial feature eliminates the need to re-key your last entry. The TS22 Test Set offers an unbeatable combination of reliability, durability and expanded utility.
-
Product
Electromagnetic Testing
-
Xiamen IDEA Electronic Technology Co., Ltd.
Is the process of inducing electric currents or magnetic fields or both inside a test object and observing the electromagnetic response.
-
Product
High-Speed Memory Test Solution
UltraFLEX-M
-
The UltraFLEX-M builds on the advanced test technology and architecture of the proven UltraFLEX test system to ensure high test quality at the lowest cost of test for high-speed memory devices.
-
Product
Test Data Management
-
With increasing test data volumes, diverse data types, complex relationships, and data sensitivity, most enterprises face significant challenges with test data management. Having good quality data is key to testing enterprise functionality correctly and efficiently in the test environment. Copying production data to be used for the test can expose the company to numerous privacy and compliance risks. In the absence of a strong test data management strategy, you may end up jeopardizing your testing cycles and pile up huge infrastructure costs.
-
Product
Package Level Test
-
Applicable for burn-in, reliability andlife testingACC and APC control modesIndividual channel driving and measurementDriving current 500mA per channel
-
Product
Electronic Test And Measurement Systems
-
Summaries, information, & tutorials about electronics test and measurement equipment & techniques.
-
Product
Plug and Switch Testing
-
Applied to test electrical accessories heating conditions when connected to load current, whether the temperature rise of electrode is compliance with standard requirement or not. And it can effectively detect whether the plug bush is slants thin and whether plug and socket cooperated with all right.
-
Product
Test Engineering Projects
-
Precision Development Consulting Inc
Fiber Optics Test System, Data Collection, Trident Missle Components, PC Board Functional Test and Bearing Tester
-
Product
Automatic Test System
Star-Rec
-
Test entire HDI panel at once, or step & repeat in the "feed" direction. Fastest BGA Strip test system available. Star-Rec comes standard with: * loader * board cleaner * CCD Camera Alignment * electrical test section * fail and pass re-stackers * Board Marker
-
Product
Surgical Instruments Testing Equipment
-
High voltage testing can be used to check insulation on diathermy instruments, surgical forceps and cables.
-
Product
Detector Test Bench
RTB 3000
-
The RTB 3000 Detector Test Bench from Santa Barbara Infrared (SBIR) is a flexible integrated IR detector test station for evaluation of single element detectors, linear arrays, and focal plane arrays. The RTB 3000 provides the radiometric stimulus necessary to perform accurate IR detector testing in both laboratory and production environments.
-
-
Product
Test Facility
-
Emprise has extensive experience designing test facilities for the aerospace, automotive, industrial and power generation marketplaces. The cost of a test facility is usually directly proportional to the accuracy of the test simulation.
-
Product
Remote Speed Test, Wi-Fi
-
Measure Wi-Fi performance — at key locations, 24×7. Remote Speed Test automatically runs network and app performance tests all day, every day. Just connect the Remote Speed Test sensor to your Wi-Fi and we’ll do the rest! Performance results collected by all your sensors are delivered conveniently to your smartphone. 802.11 b/g/n/ac 2.4 and 5.0 GHz
-
Product
Optical Loss Test Set
KI 23400
-
A Bidirectional Optical Loss Test set (OLTS) that's perfect for medium to ultra-high fiber count loss, length & ORL testing. A pair of compact instruments set new standards of productivity, accuracy, and ease of use.
-
Product
Multi-Device Cellular Signaling Test Solution
IQcell
-
Available in 2-port and 8-port configurations, IQcell™ is a cellular signaling test solution that supports the following key cellular technologies: LTE-FDD, LTE-TDD, WCDMA/HSPA, GSM. 2-Port Configuration – Turnkey Solution for IoT Device Verification. 8-Port Configuration – High Test Efficiency for Manufacturing.
-
Product
High Voltage Test Equipment
-
A hipot test is conducted by ensuring no current flows from one point to another on a circuit. A hipot test will take two conductors that should be isolated from one another and passes a high voltage between the two points. The current which flows between these points is then measured. If too much current flows, this would indicate that the points are not well isolated and the test will fail.
-
Product
Test Valva Score
AI
-
Test Value Score is a revolutionary AI-powered feature that dynamically assigns a score to each test according to the contribution it provides to the testing process. The Test Value Score allows Test Managers to optimize their testing operation under time constraints and budget limitations.
-
Product
Custom Environmental Test Chambers
-
Does your environmental testing conditions have special requirements, or are you unsure of the right product for you? Tenney and Lunaire Environmental offer custom environmental test chambers - including custom climate chambers and custom vacuum chambers. The experienced Tenney and Lunaire team can provide customizations to their climatic chamber models based on client needs. Contact the sales team today to discuss you specific testing requirements.
-
Product
Amplifier, Switch and Test Box
CLIOQC Model V
-
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
-
Product
High Voltage Test Station
-
High-voltage test stations place high demands on the safety aspect. We design these test stations in cooperation with our manufacturers as self-sufficient test systems.
-
Product
O.E.M. Specific Test Charts
-
O.E.M. Specific Test Charts by Applied Image - IMATEST SFRPlus Chart, ISA ColorGauge Targets, ISA Device Level Target, ISA Object-Level Target Family, ISA Spatial Frequency Response Target
-
Product
Diving Technology Test Systems
-
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
The imaging ultrasonic testing systems of the USPC 30XX series are optimized for testing a wide variety of materials and provide high-resolution findings in the form of A, B, C, D and F images. The hardware consists of an industrial PC, in which a motor controller and an ADC card are installed, as well as a HILL-SCAN pulser/receiver unit. An overview of the available systems is given in Table 1.
-
Product
Test Automation Management
-
In many organizations, testing is split: Automation testing is still disconnected from manual testing, and results are reported separately. This makes holistic decision-making, based on the overall testing, close to impossible. Running and managing both your manual and automated tests in PractiTest ensures the coverage of your entire process and gives you a holistic view of your entire QA operation. PractiTest is a centralized solution that helps you make data-driven decisions, focus your team’s efforts and improve your process.
-
Product
Solar Radiation (Sunshine) Test
-
This test determines the effects of direct solar radiation on components and material. The heating effects of solar radiation differ from those of high air temperature in that the amount of heat absorbed depends on the roughness and color of the surface on which the radiation is incident and the angle of incidence to the sun. Variations in the intensity of solar radiation over the surface of the component, may cause components to expand or contract at different rates, which can lead to severe stresses and loss of structural integrity. In addition, degradation due to photo-chemical changes can occur such as fading of color, deterioration of natural and synthetic elastomers and polymers. The test items that are subjected to solar radiation testing are those that are exposed to solar radiation during its life cycle, in the open, in warm climates.
