AC DC Electronic Loads
-
product
Desktop AC Power Supply
DRJ Series
DRJ Series is a stable sine wave output AC power supply of the world's smallest class that integrates the functions of rack-mount multifunctional AC power supply DRA Series in a desktop size. It is a new type of AC power supply that addresses both space saving and high-quality output that are required in experiments, evaluation tests, production line and so forth. With worldwide input feature DRJ can be used anywhere in the world. In addition, it delivers simple operability in a compact size, allowing first timers to operate easily.
-
product
AC Power Source
LSP-500VAR
• AC-DC-AC frequency conversion technology, Controlled & tested by 16 bits MCU • Protection for over hot, thundering voltage and current • Total voltage distortion: ≤0.3%; Voltage stability: ≤0.05%/30min • Load adjust rate: ≤0.05%; Frequency stability: ≤0.01%/30min • Output voltage range: AC 0.0~300.0V, Output Frequency Range: 45~70Hz, 100Hz, 200Hz and 400Hz • It is pure sine wave AC power source with low harmonic and high accuracy • Input Power: 220V and 50/60Hz (110V can be option) • Communicate with PC via software, the Voltage & Current set by the software and Power Output can be remote controlled.
-
-
product
DC Voltage/Current Generators
Pulse generation/measurement with basic accuracy of ±0.02% and the minimum pulse width of 50μs, maximum output of 6V/5A
-
product
Load Cell Tester
LCT-Ultimate
Industrial Measurement Systems Ltd.
This most advanced Load Cell Tester model LCT-Ultimate is a stand-alone hand-held device that was especially designed for full trouble shooting of strain-gage based load cells. The LCT-Ultimate can check all common types of standard load cells that are available on the market:
-
product
AC Voltage Testers
ALT Series test sets are designed for testing aerial lift devices (bucket trucks) but can also serve as portable, versatile all-purpose AC testers with an output of 0-60/120 kV AC @ 7 kVA, ideal for field, plant, and substation testing.
-
product
Serial AC Power Sequencer
90-200-001
Each power outlet can be programmed to switched on in sequence with a specific timing delay. The delay can be staggered to ensure that order dependent systems - like PXI - can be switched on and off in an orderly way with just one operation. A staggered start up also limits the inrush current associated with the powering up of equipment, including earth current inrush, placing less stress on cabling and leakage breakers. Power on or off instructions can be initiated from either the front panel switch or via the serial interface.
-
product
Control Electronics
Data acquisition and control electronics for optical radiation sources and measurement systems including precision current and voltage supplies for LEDs and tungsten halogen lamps.
-
product
Electronic Engine Controls - FADEC
The EMC-100 is dual channel Full Authority Digital Engine Control (FADEC) system, designed for helicopter turboshaft engines. The electronic control unit’s (ECU) primary channel provides precise engine power management and rotor speed control throughout the operational range of the engine. The reversionary backup channel provides full mission capability should a primary system failure occur.
-
product
RF Waveguide Load
RF Lambda’s waveguide loads are used at end of an RF signal chain to provide a good 50ohm match and dissipate any RF energy into heat. They are available in a variety of power levels and offer low VSWR.
-
product
Electronic Equipment Testing System
The task set forth the need to create a special universal software core, the main tasks of which are the provision of measurement and control processes, as well as the interaction of software components intended for collection, visualization, mathematical processing and documenting of data. For each stand, specific program modules were additionally developed according to test methods specific products. The overall modular architecture of the system makes it easy to supplement and correct test algorithms.
-
product
AC Source
AFV
The AFV Series is a broad line of programmable three phase AC power sources. With Power levels ranging from 15kVA up to 2MVA, the series powerful FPGA+ARM based controller offers precise voltage and frequency conversion with power disturbance generation capability. Power is supplied by state-of-the-art IBGT pulse-width-modulated power amplifiers resulting in highly efficient power conversion, compact design and maximized performance.
-
-
product
AC to AC Non-Programmable Power Sources
AFC Series
CEHCO can supply AC to AC Non-Programmable Power Sources. We offer standard or customized solutions. The AFC Series is from 500 VA to 2000 KVA.
-
product
Load Length Meter
Design for finding out the total voltage of neon tubes in a circuit, help to Choose correct rating of neon transformer;- Easy to use just like a neon transformer;- With color LED indicators, clearly shows the test result;- With build-in over voltage protection circuit.
-
product
Interface And Load Box
MS 3646I
Interface and Load Box is standard portable 19” rack mountable unit. It is customized unit for single channel tester of IFCC. This unit has cable/harness interface between CPCI System and IFCC LRU. This box also houses all actuator loads and switching circuits.
-
product
DC Alignment
SEP/SIP
There are analog phase control type DC power supply type and digital control type inverter energy saving type. We provide the most suitable equipment according to the current capacity and cycle time.If the "start command" is executed from the existing molding equipment, each mode of "alignment-pause-demagnetization" is continuously operated by the program inside the instrument. It is also possible to share an emergency stop signal and output an output current abnormality signal.
-
product
SQUID Electronics
SEL-1
SEL-1 is a robust and proven SQUID electronics for high-Tc and low-Tc SQUIDs and magnetometers.
-
product
Test system for Electronic Device
PCB
The main focus of the test system is validation and functional testing of electronic devices. The tests include electrical parameters and logical functions of the firmware. Device groups can be stimulated externally and output signals can be acquired by the test points on the board. Limits and ranges of the acquired signals can be monitored and stored for verification.
-
product
Loadpin Load Cell
LP
Designed to replace pins or bolts that carry a loadStainless steel constructionCapable of 100% humidity, 30G mechanical shock and 5G vibrationUsed with clevises, or pulley shafts to monitor loadsCapacity 1,740 lbf
-
product
110-125V AC Receptacle Tester
1933A
Peaceful Thriving Enterprise Co Ltd
Test for 110-125V AC circuits.Detect faulty wiring in 3 wire receptacle.
-
product
AC To DC Power Supply: 12V 25A
#TPS120
AC to DC Power Supply: 12V 2.5A with intl adapter plugs for (NA, EU, AU, UK), 849160008446
-
product
DC Tester
The DC Tester is a Voltage and Ampere breakout for measuring DC current from 0-26V at 3.2A Max (when used with the USB Tester OLED Backpack). The DC jacks make it easy to measure a wide variety of devices by placing it inline between your power supply and your project without splicing cables, just like the
-
product
Filtered AC Interface Module
AC modules for RF Test Enclosures eliminate conducted and radiated interference, while providing a source of AC power.
-
product
Capacitor for AC Filtering
PECA4 (440V)
Lifasa - International Capacitors, SA
These capacitors are especially suitable for applications where high levels of AC voltage are required. The design of this series has been optimized for the manufacture of high performance AC filters for compensation equipment with high pollution such as UPS or wind turbines.
-
product
Single Point Load Cells
These have a range of different platform sizes and are suitable for different applications including bench scales, counting scales and other applications in many industries. Click the links below to find out more about each product and to view specific data sheets.
-
product
Electron Microscope Analyzer
QUANTAX EDS for TEM
Long standing expertise in EDS ensures the configuration of the best solution for your specific microscope (STEM, TEM or SEM) thanks to slim-line detector design and geometrical optimization for each microscope pole piece and EDS flange type
-
product
AC Power Sources
GUPS (Global UPS)
AMETEK Programmable Power, Inc.
Elgar GUPS are ruggedized on-line "UPS's" that accept a broad range of worldwide utility and military AC input power. Without operator intervention, they automatically select the appropriate input power ranges to accommodate global operation. The GUPS Series has been specifically designed to withstand the rigors of mobile applications. They meet the vibration and shock requirements as specified in MIL-STD-810E, Methods 514.4 and 516.4. Their rackmounted aluminum chassis with stainless steel hardware withstands harsh environments and provides a strong, light weight enclosure.
-
product
Ion & Electron Detection
Photonis is the global leader in the development and manufacturing of detectors and optical components to detect ions and electrons. These detectors and components have been designed for a wide range of scientific instruments used in space and research projects but also in cells and material analysis in lifescience or non destructive testing.
-
product
Scanning Electron Microscope
Verios G4 XHR SEM
The Thermo Scientific™ Verios G4 scanning electron microscope (SEM) provides sub-nanometer resolution from 1 to 30 kV and enhanced contrast needed for precise measurements on materials in advanced semiconductor manufacturing and materials science applications, without compromising the high throughput, analytical capabilities, sample flexibility and ease of traditional Scanning Electron Microscope (SEM).
