Transmission LIne
See Also: Transmission Line Pulse
-
Product
LXI 2.4GHz 50ohm 16x16 Matrix
60-770-003
Matrix Switch Module
The 60-770 is a family of integrated RF matrices suitable for use up to 2.4GHz in a 50 ohm transmission line system. The matrix design permits any single Y input to be connected to any single X input, permitting the concurrent connection of 16 RF paths. All signal paths are bi-directional permitting any connection to be used as an input or an output.
-
Product
LXI 2.4GHz 50ohm 16x8 Matrix
60-771-003
Matrix Switch Module
The 60-771 is a family of integrated RF matrices suitable for use up to 2.4GHz in a 50 ohm transmission line system. The matrix design permits any single Y input to be connected to any single X input, permitting the concurrent connection of 8 RF paths. All signal paths are bi-directional permitting any connection to be used as an input or an output.
-
Product
Digital Line Protection System
DLPD
-
The DLPD provides distance protection for HV and EHV transmission lines. It may be used for single or three phase tripping applications. It includes four zones of distanceprotection. User selectable pilot schemes are provided with stepdistance backup. Ground instantaneous and time overcurrentfunctions are independently selectable to be directional ornon-directional.
-
Product
TDR Structural Health Monitoring
-
Material Sensing & Instrumentation
MSI Time-Domain-Reflectometry (TDR) Structural-Health Monitoring probes the structural health of a composite part by propagating a fast electrical pulse along a distributed linear sensor which has been fabricated directly in the laminate. The sensor is formed from the native graphite fibers already used in composite manufacture, and constitutes zero defect. Fibers are patterned into a microwave waveguide geometry, or transmission line, and interrogated by a rapid pulse as shown below. Structural faults along the line cause distortions in waveguide geometry, producing reflected pulses similar to radar. Cracking, delamination, disbonds, moisture penetration, marcelling, and strain are all detected by propagation delay, for sensor lengths up to several meters.
-
Product
LXI WTB Terminator, 109.8 ohm
60-983-003
Terminator
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
Product
RF Hybrid Couplers
-
Pasternack RF hybrid coupler series is passive devices that couple part of the transmission power in a transmission line. Our RF hybrid coupler components provide the bandwidth, high directivity and high power that designers need for their most demanding applications. 90 degree hybrid couplers often use two transmission lines set close together so that energy passing through one is coupled to the other. Many Pasternack 90 degree hybrid coupler items are RoHS and REACH compliant. Our RF hybrid coupler series is available with SMA connectors and 3dB coupling values. Power ratings for the 90 degree hybrid coupler product line range from 20 Watts to 50 Watts. 90 degree hybrids have a frequency range that is from 1 GHz to 18 GHz. As with the other over 40,000 RF, microwave and millimeter wave components from Pasternack, this RF hybrid coupler series is in-stock. Not just in stock, but these RF couplers in a hybrid design will also ship the same day as they are purchased.
-
Product
Transmitters
-
The Spy Pig Tracker is an electronic pig locating system that will locate your pigs wherever they go – through gathering lines, mainline transmission lines, municipal gas, water and waste water lines, refinery and other industrial piping.
-
Product
Panel Mount Meters
-
The Coaxial Dynamics series of High-Power Panel Mount Meters are designed to measure RF power in 50-Ohm 1-5/8 to 6-1/8 inch coaxial transmission lines. Several different models are available with either 5/10/25 scales or 15/30/60 scales. The Panel Meter can be installed up to 200-feet from the Line Section with the permanently attached DC cables (10-foot normally supplied).
-
Product
Broadband, Multirange Directional RF Wattmeter
81060
-
With the Model 81060 Directional Wattmeter you can now measure RF power in 50-Ohm coaxial cable and transmission lines without the need for additional plug-in elements.
-
Product
Microwave Coaxial Cable Assemblies
MWX0 series
-
JUNFLON® MWX products are flexible signal transmission lines that take advantage of the remarkable properties of fluoropolymers. They are suitable for use with a wide range of frequencies up to 67 GHz. These products feature low insertion loss and low VSWR, low signal leaks and low interference due to high shielding effectiveness, and higher density wiring for use in the narrow device interiors. Junkosha provides highly reliable products for microwave /millimeterwave applications tailored to customer assembly needs.
-
Product
Power Detectors
-
Macom Technology Solutions Holdings Inc.
MACOM’s power detectors are broadband devices that have integrated low loss directional couplers and built-in temperature compensation circuits. These detectors provide an easy way to monitor the power of a signal travelling in a specific direction along a transmission line. These detectors are conveniently housed in miniature lead free plastic surface mount package. Typical applications include; Power monitoring and leveling in Point-to-Point radios, IMS, Radar, VSAT, EW, Aerospace and Defense Systems.
-
Product
LXI 2.4GHz 50ohm 16x4 Matrix
60-772-003
Matrix Switch Module
The 60-772 is a family of integrated RF matrices suitable for use up to 2.4GHz in a 50 ohm transmission line system. The matrix design permits any single Y input to be connected to any single X input, permitting the concurrent connection of 4 RF paths. All signal paths are bi-directional permitting any connection to be used as an input or an output.
-
Product
Coaxial Waveguide Adapter, 3.5 mm (f), 18 to 26.5 GHz
K281C
Coax Adapter
The Keysight K281C adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can be transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.07.
-
Product
Personal Computer Aided Antenna Design
PCAAD 7.0
-
Antenna Design Associates, Inc.
PCAAD 7.0 is a Windowscompatible antenna analysis, modeling, and design software package. It contains more than 50 routines treating wire antennas, aperture antennas, microstrip antennas, arrays, transmission lines and waveguides, and more. These routines are integrated into a menudriven, userfriendly system allowing you to quickly evaluate the performance of a wide variety of antenna types. PCAAD 7.0 includes a 120-page printed user manual which describes the use of the software, provides examples for each of the routines, and lists technical references.
-
Product
Pulse generator
9355-1
-
Solar Model 9355-1 Pulse Generator is designed to provide impulse excitation by means of an injection probe placed around interconnecting cables or power wires. The unit uses a charged transmission line (50 ohms) to generate a pulse with less than 2 nanoseconds rise and fall time, and duration of approximately 30 nS, calibrated in a 50 ohm fixture to deliver up to 5 amperes at a rate of 30 p.p.s. for one minute as required by MIL-STD-461D/E, test method CS115.
-
Product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 4 Channel
40-200-004
CAN Interface
Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signaling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
Power Dividers & Splitters
-
Keysight dividers and splitters are used in a wide range of applications, such as: transmission line fault testing, power combining, source leveling, ratio measurements, power splitting, and critical signal processing applications that require minimal insertion loss and high port isolation.
-
Product
Coaxial Waveguide Adapter, 1.85 mm (f), 40 to 60 GHz
U281A
-
The Keysight U281A adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
LXI 2.4GHz 50ohm 24x16 Matrix
60-770-002
Matrix Switch Module
The 60-770 is a family of integrated RF matrices suitable for use up to 2.4GHz in a 50 ohm transmission line system. The matrix design permits any single Y input to be connected to any single X input, permitting the concurrent connection of 16 RF paths. All signal paths are bi-directional permitting any connection to be used as an input or an output.
-
Product
Coaxial Components
-
Surge arrestors are designed to protect wireless base stations, switching centers and transmission lines fromthe damaging effects of extreme high voltage surges caused by lightning strikes. The RFS lightning protectiondevices are designed and tested to the most demanding specifications. They are rated to protect against bothdirect and indirect multiple strikes in the harshest environments imaginable. Their rugged construction utilizes solid metal housing, and superior plating, which results in outstanding system protection and operatingcontinuity.
-
Product
SWR / Power Meters
-
A device used primarily by radio operators to measure the Standing Wave Ratio (SWR) and forward and reflected power in a transmission line, like a coaxial cable.
-
Product
Cable Fault Locating Equipment
-
Commonly used to test underground coaxial and twisted pair cabling, along with transmission lines and other industrial electrical cables.
-
Product
Transmission Lines
-
SemiGens 50-ohm Transmission Lines offer the RF/microwave designer complete flexibility and repeatability for the most challenging applications.
-
Product
100-Watt DC Power Line Conditioner w/Holdup
44LS1
Power Line Conditioner
NAI’s 44LS1 is a 100-Watt Power Line Conditioner with holdup time that protects downstream DC/DC converters from transients, low voltage conditions, and power interruptions. This unit accepts +28 VDC input and provides 22.5 to 30 VDC at 100 Watts to all downstream DC/DC converters.
-
Product
Coaxial Waveguide Adapter, 2.4 mm (f), 33 to 50 GHz
Q281A
-
The Keysight Q281A is a 2.4 mm female to WR-22 waveguide adapter that operates in the 33 to 50 GHz frequency range. These adapters transform waveguide transmission lines into 50 ohm coaxial lines. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Panel Mount Wattmeters
-
The Coaxial Dynamics series of Panel Mount Wattmeters are designed to measure RF power in 50-Ohm coaxial cable and transmission lines, and accept plug-in elements in the range of 100 mW to 10 kW full scale, and from 0.45 to 2300 MHz
-
Product
High-Power Directional RF Wattmeters
81100-A Series
-
The 81100-A series of High-Power Directional RF Wattmeters are designed to measure RF power in 50-Ohm 1-5/8 inch coaxial transmission lines. To use the Wattmeter, simply connect it between the transmitter and antenna or dummy load and plug in the appropriate measuring element.
-
Product
Coaxial Waveguide Adapter, 2.4 mm (m), 33 to 50 GHz
Q281B
-
The Keysight Q281B is a 2.4 mm male to WR-22 waveguide adapter that operates in the 33 to 50 GHz frequency range. These adapters transform waveguide transmission lines into 50 ohm coaxial lines. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
72.5-Watt DC Power Line Conditioner w/Holdup
44KS3-02
Power Line Conditioner
NAI's 44KS3-02 is a 72.5-Watt Power Line Conditioner with holdup time that protects downstream DC/DC converters from transients, low voltage conditions, and power interruptions. This unit accepts +28 VDC input and provides a single output at 72.5 Watts either 22.5 to 30 VDC with holdup time or +16 VDC without holdup time - to all downstream DC/DC converters.
-
Product
Impedance Measurement
CITS880s
-
Finer geometries and thinner copper can present a challenge for fabricators measuring impedance on leading edge PCBs. The CITS880s answers that challenge with the introduction of Launch Point Extrapolation (LPE). LPE extrapolates the TDR response back to a point close to the start of the transmission line effectively allowing to users more accurately to measure the instantaneous or incident impedance of the line.
