-
-
product
Acceleration Testing
The acceleration test is performed on a centrifuge to assure that material can structurally withstand the steady state inertia loads that are induced by platform acceleration, deceleration, and maneuver in the service environment, and can function without degradation during and following exposure to these forces. Acceleration tests are also used to assure that material does not become hazardous after exposure to crash loads. The acceleration test method is applicable to material that is installed in mobile platforms such as aircraft, helicopters, aerospace vehicles, air-carried stores, ground-launched missiles, trains, ships, automotive vehicles, etc.
-
product
Dissolution Testing
Agilent offers laboratories the pharmaceutical dissolution testing apparatus, dissolution accessories, and dissolution software for efficient and reliable dosage form testing. Extensive dissolution skills training is also offered to meet the needs of all busy laboratory analysts. Feel confident with Agilent dissolution testing apparatuses. All systems meet the international harmonized guidance requirements defined by USP, EP, CP, IPC, and JP for effective drug dosage form testing. Laboratory analysts can efficiently meet data integrity requirements too. Working to Title 21 Code of Federal Regulations (CFR) part 11 compliance standards is readily achieved using Agilent dissolution testing software.
-
product
Eddy Covariance Systems
LI-COR eddy covariance systems measure the exchange of CO2, H2O, CH4 , and energy between the earth's surface and the atmosphere, empowering researchers to advance scientific understanding of climate and ecosystem dynamics.
-
product
USB System Timer
SKU-077-0X
The USB System Timer uses a standard USB interface to synchronize IP signals. This system timer provides accurate clock timing for Asterisk® open-source PBX software.
-
product
Thermal Testing
At E-Labs, Inc., we support thermal cycling and thermal bakeout vacuum testing requirements. During thermal cycling, the unit experiences repeated heating and cooling as it would when exposed to the harsh environment of space. During thermal bakeout, flight equipment is subjected to an outgassing reduction process so as to decrease the chance of molecular contamination of the spacecraft instrumentation.
-
product
Cellular Base Station Factory Test Systems
*Factory Test System*Designed and Built by BCO*100% Functional Testing*Environmental Stress Screening Testing
-
product
Test Fixtures & Test Sets
Keysight test fixtures are used to hold electronic components or materials (physically and electrically) in order to perform various measurements. Keysight offers a variety of test fixtures from Parametric, Dialectrice, Liquid test fixtures and more.Some of our test fixtures allow you to connect directly to your measurement instrument, while others require various adapters.
-
-
product
Motor Testing
Electronic Systems of Wisconsin, Inc.
ESW's Motor Test Systems come fully equipped with the latest industry features based on your testing needs. The on-screen display in our testers make it easy to read, track, and record your motor information during the testing process. We realize this importance and want to make sure you never have to worry about losing key information ever again. Performance and reliability are important, so we make sure you will have full confidence of every motor you test, whether you place it in your product or send out the door to your customer. ESW's design team works closely with you to determine the tests you need, in order to make a system that will meet all your testing needs. See the slideshow below to see some of our Motor Testers.
-
product
Material Testing
*Abrasion Testing*Adhesion Testing*Brittleness Temp.*Bursting Strength*Coating Testing*Coefficient of Friction*Compression Testing*Compression Set*Dart Drop Testing*Density Determination*Fatigue Testing*Fiberboard Testing*Flammability Testing*Flexural Testing*Foam Testing*Hardness Testing*Heat Deflection*Hydrostatic Testing*Impact Testing*Life Cycle Testing*Melt Index Testing*Plastic Testing*Ply Separation*Resin Content*Rubber Testing*Shear Strength Testing*Stress Crack Testing*Tear Testing*Temperature Testing*Tensile/Elongation*UV Exposure*Water Absorption*Wood Testing
-
product
Test Adapter
FECVF1600
Frothingham Electronics Corporation
The VF1600 Test Station is a high current forward pulser designed to be used in conjunction with our FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of much higher forward current. The VF1600 station can produce a maximum current of 1600A at up to 5V using an 8.3 mS half sine waveform at the built in test station, and THETA and DVF tests at up to 500A at 10mS pulse width. It is derated for wider pulses. For rectangular VF pulses at 300us or 1ms, it can produce up to 2000A. The station can also test all of the usual FEC200 tests in the same test program.
-
product
Environment Monitoring System
ENVIROMUX-2D
The ENVIROMUX-2D supports 2 external configurable sensors, 5 digital inputs, and 1 output relay for control of external devices. It features 2 USB ports for USB modem, USB flash drive, or USB LCD screen. Linux inside.
-
product
Usability Testing
Do your customers have to navigate through a maze of actions on your application to achieve what they need to? Are your customers leaving your website without completing the purchase since they could not find the right link or page?
-
product
Pneumatic Vertical Shock Response Spectrum Test System
KRD14 series
KRD14 series pneumatic shock response spectrum tester is used to measure and determine the shock resistance of electrical and electronic products or packaging, and to evaluate the reliability and structural integrity of the test product in a shock environment. The shock response spectrum is the total result of a series of single-degree-of-freedom linear systems with different natural frequencies subjected to the same shock excitation response. When a product is subjected to an impact, the maximum value of its impact response means that the product has a maximum stress. Therefore, the shock response spectrum tester can better simulate the shock wave and shock energy suffered in the real environment.
-
product
Data Acquisition Systems
m+p Coda is a full-featured turnkey software platform for data acquisition, signal analysis and monitoring. Complete turnkey operation provides quicker time to test by eliminating costly application programming and long learning curves. The extensive built-in features and tools offer a functionality that was previously available only in custom packages. The intuitive graphical user interface facilitates set-up, operation and analysis, thus leading to precise, repeatable results quickly.
-
product
Geophone Testing – Hydrophone Testing – Vibrator TestingVersatile Quality Control System - Three Test Units In One!
Bird Dog 3 - 3 Channels
*32-bit, high speed, ADC chip for lower noise and increased accuracy*Three different operation with a single unit*8 Gigabytes of Data Storage, Expandable to 16*GPS based time and location saved for every record*Stable and rugged unit for use in all conditions*Three-Component Test Mode, checks 3 elements at onceto save time and effort*All test data saved in non-volatile memory for later download and retrieval*Connects to PC via Ethernet or optional Wi-Fi, provides control, data download and real time display and analysis of data and results
-
product
High-Voltage System
Is designed to control power flow to and from the cells and to maintain the power level within the design envelope.
-
product
Test Handler
HA1200
The new HA1200 handler can be linked with a tester to utilize our unique active thermal control technology for testing singulated and/or partially assembled dies. This technology enables testing of powerful high-end SoCs with 100% test coverage. This helps reduce yield loss at final test, thus reducing losses of final multi-die assembled products.
-
product
Optics Test Systems
Lens Test
Optik Elektronik Gerätetechnik GmbH
LensTest enables the measurement of air gaps, lens thickness, lens radii and lens surface centration errors in mounted lenses as well as the active alignment of lens surfaces during optics assembly for centering without rotating the assembly.
-
-
product
Control System
HICOS
HIGHVOLT Prüftechnik Dresden GmbH
The HiCOS controller is a collection of modules for monitoring test systems and recording, creating, evaluating and evaluating measurement data. It is suitable for mobile and stationary test systems as well as measuring devices. The modular design of the HiCOS controller allows the expansion of functions. Existing test systems from other manufacturers can be upgraded with HiCOS.
-
product
S-Parameter Measurement System
DPS08
KEYCOM provides S-parameter method measurement systems in two modes, the reflection mode and the transmission mode, to address the individual purposes. Both modes measure the complex permittivity (εr) and complex permeability (μr) at the same time, and the proper usage is as follows.
-
product
Linear Metrology System
The ZeroTouch® Linear Metrology System is a high-speed, non-contact linear inspection system ideal for measuring linear-shaped parts such as hip stems and aerospace blades faster than traditional methods.
-
product
Inspection Systems
Video Inspection Systems with?or without measurement capabilities are an excellent way to evaluate and test small items or items in?difficult to access locations. Many options are available in addition to the measurement capability. Video Inspection is used for a variety of purposes including the ability to see? and measure items that are much smaller than the eye can see or that hand tools can measure. Video systems can also reduce the eye and/or back strain associated with production environments where an operator must look in a microscope all day.
-
product
Data Acquisition Systems
Includes measurement devices, sensors, a computer, and data acquisition software.
-
product
Test Adapter
RAMCHECK® SIMM
The RAMCHECK SIMM Adapter is another addition to the RAMCHECK memory tester. It provides a needed solution for testing older 72-pin EDO/FPM DRAM SIMM modules. An optional adapter for 30 and 72-pin SIMMs is also available
-
product
Corrosion Test
The purpose of this test is to determine the resistance of materials and protective coatings to corrosive atmospheres when a more corrosive environment than the salt fog/spray test is required. The test is used when material is stored or operated in areas, for example, where acidic atmospheres exist, such as in industrial areas or near the exhausts of any fuel-burning device. Gases such as sulfur dioxide are used to replicate the exhausts of fuel burning devices.
-
product
Physical Testing
Testing is confidential and can be conducted according to the client's specifications, or such Standards as MIL-202, 331, 750, 810 and 883, as well as GSA, ASTM, ISTA, BIFMA, ANSI, industry and government.
-
product
Data Monitoring System
1S663-001
The 1S663-001 Data Monitoring System was specifically developed for the Cessna Citation X and serves as the primary diagnostic tool for the aircraft?? electronic Logic Modules. The system is FAA certified for airborne operation. Aft compartment and cabin modules can be tested two at a time while remaining in place. The system is also capable of monitoring the fuel quantity system during flight.
