Polarization Mode Dispersion
Polarization Mode Dispersion
-
product
250 MHz 60 V Common Mode Differential Probe
DL02-HCM
60 V of common mode and 80 V differential input range with 1 GHz of bandwidth, make these probes ideal for lower voltage GaN power conversion measurements. The 60 V of common mode is well suited for handling any float of the battery and bulk/absorption voltage during charging, while the 80 V differential input range provide margin for any overshoot.
-
product
LXI Dual 8:1 Optical MUX LC Single Mode
60-850-412
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
product
Transformer Polarity Tester
PMT20030
Power Measurement Technologies Inc.
A hand held instrument for polarity identification of current, voltage and power transformers with an operable ratio range from 1:1 to greater than 5000:1.
-
product
1 GHz 60 V Common Mode Differential Probe
DL10-HCM
60 V of common mode and 80 V differential input range with 1 GHz of bandwidth, make these probes ideal for lower voltage GaN power conversion measurements. The 60 V of common mode is well suited for handling any float of the battery and bulk/absorption voltage during charging, while the 80 V differential input range provide margin for any overshoot.
-
product
Multi-angle Polarized Light Scattering Measurements
LISST-VSF
In-situ measurements of P 11, P12 and P22 elements of scattering Mueller matrix, (P11 is VSF) from 15-150º.VSF (P11) only at small angles, 0.05 to 10º in 32 logarithmic steps in angles.Only two detectors employed with absolute radiant sensitivity (A/W) calibration.Beam attenuation measured with optics similar to our LISST-100X.Roving Eyeball™ optics permit 1-degree resolution in angles between 15 -150º.Sampling rate at 3 seconds per measurement set (involves 3 turns of Roving Eyeball with unpolarized, vertical, and horizontal polarized laser).Daylight rejection by laser modulation.Dynamic range in VSF measurements extended via laser power modulation.Data from small and large angles in a single data stream, including depth and temperature.
-
product
Acceleration Simulation Mode Roller Set for Vehicles with a Single Driven Axle
ASM-BF/1 | VP 230043
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-BF/1 roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97.
-
product
Single Mode Multimode Test Inspect Kit
KI-TK072A
1310/1550/1625 nm & 850/1300 nm source & Autotest power meter + acceptance reporting software, inspection microscope, cleaning materials. Interchangeable SC/APC & LC/APC connectors
-
product
Benchtop Polarization Analyzer
N7781C
The Keysight N7781B is a compact high-speed Polarization Analyzer which provides comprehensive capabilities for analyzing polarization properties of optical signals. This includes representation of the State of Polarization (SOP) on the Poincar Sphere (Stokes Parameter).
-
product
Polarization Controller
Shenzhen Golight Technology Co.,Ltd
Polarization controller integrates an all-fiber dynamic polarization controller and a mini piezoelectric ceramic actuator. As a polarization controller, it can convert any input polarization state to the desired polarization state output. As a polarization scrambler, it can effectively disrupt the output polarization state.
-
product
LXI Dual 8:1 Optical MUX SC Multi Mode
60-851-212
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
product
A Ready-to-use Solution To Orientate Polarization Maintaining Fibers Inside Connectors
PM ALIGNER-V2
PM Aligner-V2 is the simplest way to orientate precisely a PANDA Polarization Maintaining fiber inside a connector or ferrule. With a long working distance, PM Aligner-V2 allows the operator to work manually around the ferrule of the connector. After positionning, the curing phase becomes easy to realize without affecting on the PM fiber alignement.
-
product
LXI 8:1 Optical MUX LC Single Mode
60-850-411
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
product
PXI Single 2 x 2 Fibre Optic (M Mode)STM62.5
40-860-512-M62.5
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
Polarization Instrumentation
This page features the optics and instrumentation necessary to control and measure the polarization of light. Our free-space and fiber-coupled polarimeters can measure any state of polarization (SOP) on the Poincaré sphere.
-
product
LXI 16:1 Optical MUX SC/PC Single Mode
60-850-213
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
product
Mini Fiber Optical Switch at Single Mode Latching 1310/1550nm 5V with LC/PC Connector
SUN-FSW-1x4
Guilin GLsun Science and Tech Group Co., LTD
GLsun 1*4 Optical Switch micaro optical switch informationFeatures•Low Insertion Loss•Wide Wavelength Range•Low Crosstalk•High Stability,High Reliability•Epoxy-free onOptical Path•Latching and Non-latchingApplications•F&D in Laboratory•System Monintoring•OADM•MAN(Metropolitan Area Network)•Network Security and MonitoringSpecificationsParameters Unit SUN-FSW-1×4Wavelength Range nm 850±40 / 1300±40 1260 ~ 1650Test Wavelength nm 850 / 1300 1310 / 1550Insertion Loss 1, 2 dB ≤1.0Return Loss 1, 2 dB MM ≥ 30 SM ≥ 50Crosstalk 1 dB ≥ 55PDL dB SM ≤0.1WDL dB ≤0.25Repeatability dB ≤±0.02Operating Voltage V 3.0 or 5.0Voltage Pluse Width(Latching) ms ≥ 20Durability Cycles ≥ 10 MillionSwitching Time ms ≤8Optical Power mW ≤500Operating Temperature ℃ 0 ~ +70Storage Temperature ℃ -40 ~ +85Relative Humidity % 5 ~ 95Dimension mm (L)33.5×(W)25.5×(H)9.5 ±0.2Note: 1 Within operating temperature and SOP.2 Excluding connectors.GLSUN 1x4 fiber optic switch micaro optical switch
-
-
product
I2C Fast Mode Interface for USB 2.0, I2C Multimaster and Monitor
Connii MM 2.0
telos EDV Systementwicklung GmbH
Connii MM 2.0 is a small, compact, easy-to-use solution for a PC driven I2C transmitter and receiver. The I2C interface works as an I2C multimaster device. Thus, it is able to drive buses running multiple I2C bus masters. Additionally, Connii MM 2.0 is a limited I2C monitor for traffic up to 400kHz.
-
product
RS485 Mode SI-module With Optical Isolation
MX485-G
RS485 mode SI-module with optical isolation
-
product
Energy Dispersive Spectroscopy (EDS) Detector Technology
EDS
The Element SDD is a solutions based detector, which excels at basic analysis. Focused primarily on serving the needs of the industrial market segment, it provides application specific software and analysis that can quickly provide answers in the industrial environment.
-
product
PXI Single 2 Channel (M Mode) ST 50 Cons
40-855-512-M50
Fiber Optic MEMS Switching cards available in many high density formats with a choice of five different connector styles to suit most applications
-
product
Fiber Optic Qualification & Dispersion Test Links
8800 Family
Delaire USA qualification test systems are designed to act as worst-case links for bandwidth/dispersion and attenuation, or to meet the customer's loss, dispersion, and distance requirements for custom applications. Because the test links are constructed from hand-selected, industry-standard fiber and not simulated with dispersion elements, all of the effects including loss, dispersion, and fiber nonlinearities are present and authentic. Typical applications include optical transciever testing and qualification for 40G AND 100G systems
-
product
Polarity Indicator Circuit Tester
CT8007
No ground wire means no wire tangles nor time lost searching for grounding points. High Impedance electronic circuitry. Negligible current draw ( 1 microampere) is 30,000 times less than regular lamp type testers. This gives complete safety when working around sensitive electronic control modules and sensors. Operating range between 6 and 28 Volt DC in battery powered systems
-
product
CT Polarity Tester
DIR CT
SCOPE proudly introduces Dir CT, a CT Polarity Tester specially designed to verify correctness of polarity of current transformers cores in live EHV switchyards. Polarity test is one of the most common yet crucial tests required to be done on current transformers by commissioning as well as maintenance engineers. Even though it is commonly conducted check, there was no all in one simple tool available for this measurement. DIR CT fills this void to perfection, it is expected to significantly reduce the time taken for polarity checks on numerous CT in sub-station, especially during commissioning of new sub-stations
-
product
LXI 8:1 Optical MUX FC/APC Single Mode
60-850-011
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
product
Matrix Fiber Optical Switch at Single Mode Type A 1550nm with LC/PC Connector
GLSUN-MEMS-8x8
Guilin GLsun Science and Tech Group Co., LTD
Fiber Configurations 8x8 ports Fiber Type SM, 9/125 umTest Wavelength 1530/1570 nm Operating Voltage 4.8~5.5VSwitch Type Non-latching Fiber Length 0.5m±5cmConnector LC/PC Tube Type 900 umOperating Temperature -10°C~ +70°C Storge Temperature -40°C ~ +85°C
-
product
PXI Single 2 x 2 Fibre Optic (M Mode)SCM62.5
40-860-212-M62.5
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber.
-
product
Energy Dispersive X-ray Fluorescence Spectroscopy Systems
Energy Dispersive X-ray Fluorescence Spectroscopy Systems
-
product
LXI 16:1 Optical MUX LC Single Mode
60-850-413
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
