Polarization Mode Dispersion
Polarization Mode Dispersion
-
Product
Fiber Optical Switch at Single Mode Latching 1310/1550nm 5V with LC/PC Connector
SUN-FSW-1x2H
-
Guilin GLsun Science and Tech Group Co., LTD
GLSUN 1×2H Mechanical Optical Switch Fiber Switch Features·Low Insertion Loss·Wide Wavelength Range·Low Crosstalk·High Stability, High Reliability·Epoxy-free on Optical Path·Latching and Non-latchingGLSUN 1×2H Mechanical Optical Switch Fiber Switch Applications·R&D in Laboratory·System Monitoring·OADM·MAN (Metropolitan Area Network)·Network Security and MonitoringGLSUN 1×2H Mechanical Optical Switch Fiber Switch SpecificationsParameters Unit SUN-FSW-1×2HWavelength Range nm 1260 ~ 1650Test Wavelength nm 1310 / 1550Insertion Loss 1, 2 dB Typ: 0.8 Max: 1.0Return Loss 1, 2 dB SM ≥ 50Crosstalk 1 dB SM ≥ 55PDL dB ≤0.05WDL dB ≤0.25Repeatability dB ≤±0.02Operating Voltage V 3.0 or 5.0Durability Cycles ≥ 10 MillionSwitching Time ms ≤8Optical Power mW ≤500Operating Temperature ℃ -20 ~ +70Storage Temperature ℃ -40 ~ +85Relative Humidity % 5 ~ 95Weight g 14Dimension mm (L )22.5×(W)11.8×(H)10.2 ±0.2Note: 1 Within operating temperature and SOP.2 Excluding Connectors.
-
Product
PXI Dual 2 x 2 Fibre Optic (M Mode) STM62.5
40-860-522-M62.5
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Polarization Instrumentation
-
This page features the optics and instrumentation necessary to control and measure the polarization of light. Our free-space and fiber-coupled polarimeters can measure any state of polarization (SOP) on the Poincaré sphere.
-
Product
I2C Fast Mode Interface for USB 2.0, I2C Multimaster and Monitor
Connii MM 2.0
-
telos EDV Systementwicklung GmbH
Connii MM 2.0 is a small, compact, easy-to-use solution for a PC driven I2C transmitter and receiver. The I2C interface works as an I2C multimaster device. Thus, it is able to drive buses running multiple I2C bus masters. Additionally, Connii MM 2.0 is a limited I2C monitor for traffic up to 400kHz.
-
Product
Coupling Decoupling Network for Conducted Common Mode Immunity Testing According to IEC 61000-4-6
CDN
-
The CDN M5 is intended to inject common mode disturbance signals to power supply of mains lines (unscreened) in the frequency range from 150KHz to 230MHz. A variety of calibration adapters and other accessories are available as an option. RF Standard connector: BNC type, AC socket 4mm safety bananas.
-
Product
Single Mode Fiber Test Kit
KI-TK077
-
Single mode fiber test kit for low to medium test volume on SM and MM systems.
-
Product
LXI 8:1 Optical MUX SC Multi Mode
60-851-211
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
Single Mode & Multimode Testing Kit
KI-TK076
-
Single mode & multimode testing kit with an optical power meter and light source for low to medium test volume on SM and MM systems.
-
Product
Acceleration Simulation Mode (ASM) Roller Set
ASM-P | VP 230046
-
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-P roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The increased tractive force of its eddy current brake means that the ASM-P is also suitable for power measurements at constant speed and constant tractive force.
-
Product
PXI Single 2 Channel (M Mode) ST 62.5 Cons
40-855-512-M62.5
Switch Module
Fiber Optic MEMS Switching cards available in many high density formats with a choice of five different connector styles to suit most applications
-
Product
PXI Single 2 Channel (M Mode) ST 50 Cons
40-855-512-M50
Switch Module
Fiber Optic MEMS Switching cards available in many high density formats with a choice of five different connector styles to suit most applications
-
Product
PXI Single 2 x 2 Fibre Optic (M Mode)SCM62.5
40-860-212-M62.5
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber.
-
Product
Polarity Indicator Circuit Tester
CT8007
-
No ground wire means no wire tangles nor time lost searching for grounding points. High Impedance electronic circuitry. Negligible current draw ( 1 microampere) is 30,000 times less than regular lamp type testers. This gives complete safety when working around sensitive electronic control modules and sensors. Operating range between 6 and 28 Volt DC in battery powered systems
-
-
Product
PXI Very High Density Multiplexer, 2A, 79-Channel, 2-Pole, Multiple Channel Mode
40-611B-002-M
Multiplexer Module
The 40-611B-002 (PXI) and 42-611B-002 (PXIe) modules are 79-Channel 2-Pole multiplexers. A 158-Channel 1-Pole configuration is also available. They use high quality electro-mechanical signal relays allowing switching up to 2 A and voltage up to 300 VDC/240 VAC. They are suitable for signal routing in high channel count ATE and data acquisition systems. Connections are made via a front panel 160-pin DIN 41612 connector.
-
Product
ModCon Mode Controller – Aerospace
-
*Improve measurement accuracy*Ensure stable launch conditions for multimode fiber measurements*Meet 85/85 launch conditions required in some aerospace applications.
-
Product
PXI Single 2 Channel (M Mode) SC 62.5 Cons
40-855-212-M62.5
Switch Module
Fiber Optic MEMS Switching cards available in many high density formats with a choice of five different connector styles to suit most applications
-
Product
Dispersion Compensation Optical Fiber Module
DCM-G.652-C-Fxx
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai and DCM-G.652-C-Fxx dispersion compensation fiber module, is negative dispersion compensation based on optical fiber technology, can effectively compensate for G.652 standard single-mode fiber transmission band of 1525 ~ 1565nm dispersion and dispersion slope characteristic.
-
Product
Tube-Above Wavelength Dispersive X-ray Fluorescence Spectrometer
ZSX Primus IV
-
As a tube-above sequential wavelength dispersive X-ray fluorescence spectrometer, the new Rigaku ZSX Primus IV delivers rapid quantitative determination of major and minor atomic elements, from beryllium (Be) through uranium (U), in a wide variety of sample types — with minimal standards. ZSX Guidance supports you in all aspects of measurement and data analysis. Can accurate analysis only be performed by experts ? No — that is in the past. ZSX Guidance software, with the built-in XRF expertise and know-how of skilled experts, takes care of sophisticated settings. Operators simply input basic information about samples, analysis components and standard composition. Measured lines with the least overlap, optimum backgrounds and correction parameters (including line overlaps) are automatically set with aid of qualitative spectra.
-
Product
CT Polarity Tester
DIR CT
-
SCOPE proudly introduces Dir CT, a CT Polarity Tester specially designed to verify correctness of polarity of current transformers cores in live EHV switchyards. Polarity test is one of the most common yet crucial tests required to be done on current transformers by commissioning as well as maintenance engineers. Even though it is commonly conducted check, there was no all in one simple tool available for this measurement. DIR CT fills this void to perfection, it is expected to significantly reduce the time taken for polarity checks on numerous CT in sub-station, especially during commissioning of new sub-stations
-
Product
ModCon Mode Controller – 12 Channel
-
*Improve measurement accuracy*Ensure stable launch conditions for multimode fiber measurements*Meet EF requirements of IEC 61280-4-1.
-
Product
1 GHz 60 V Common Mode Differential Probe
DL10-HCM
Differential Probe
60 V of common mode and 80 V differential input range with 1 GHz of bandwidth, make these probes ideal for lower voltage GaN power conversion measurements. The 60 V of common mode is well suited for handling any float of the battery and bulk/absorption voltage during charging, while the 80 V differential input range provide margin for any overshoot.
-
Product
Matrix Fiber Optical Switch at Single Mode Type A 1550nm with LC/PC Connector
GLSUN-MEMS-8x8
-
Guilin GLsun Science and Tech Group Co., LTD
Fiber Configurations 8x8 ports Fiber Type SM, 9/125 umTest Wavelength 1530/1570 nm Operating Voltage 4.8~5.5VSwitch Type Non-latching Fiber Length 0.5m±5cmConnector LC/PC Tube Type 900 umOperating Temperature -10°C~ +70°C Storge Temperature -40°C ~ +85°C
-
Product
Single Mode Multimode Test Inspect Kit
KI-TK072A
-
1310/1550/1625 nm & 850/1300 nm source & Autotest power meter + acceptance reporting software, inspection microscope, cleaning materials. Interchangeable SC/APC & LC/APC connectors
-
Product
PXI Single 2 Channel (M Mode) SC 50 Cons
40-855-212-M50
Switch Module
Fiber Optic MEMS Switching cards available in many high density formats with a choice of five different connector styles to suit most applications
-
Product
Simultaneous Wavelength Dispersive X-ray Fluorescence Spectrometer
Simultix 15
-
Multi-channel simultaneous wavelength dispersive X-ray fluorescence (WDXRF) spectrometer system, the Simultix 15 high-throughput WDXRF spectrometer. Analyze beryllium (Be) through uranium (U) in almost any sample matrix. The most important metrics for automated process control are precision, accuracy and sample throughput. With up to 30 (and optionally 40) discrete and optimized elemental channels and 4 kW (or optionally 3 kW) of X-ray tube power, Simultix 15 delivers unparalleled analytical speed and sensitivity.
-
Product
250 MHz 60 V Common Mode Differential Probe
DL02-HCM
Differential Probe
60 V of common mode and 80 V differential input range with 1 GHz of bandwidth, make these probes ideal for lower voltage GaN power conversion measurements. The 60 V of common mode is well suited for handling any float of the battery and bulk/absorption voltage during charging, while the 80 V differential input range provide margin for any overshoot.
-
Product
Single Mode Fiber Optic Rotary Joints
-
Single Mode Fiber Optic Rotary Joints (FORJ) can be supplied as a stand alone product. Its features can be customized : wavelength, connectors, characteristics of the fiber…
-
Product
Polarization Controller and Scrambler - MATRIQ
Controller
The Pol 1000 Series enables high-speed automated polarization control for polarization dependent testing procedures.Rotate or scramble the polarization of your signal with no need for manual adjustment of paddles or tension screws using intuitive software, LabVIEW or comprehensive SCPI commands.
-
Product
Firmware for High-speed HDLC Mode
OP-FW10
-
OP-FW10 is firmware to upgrade protocol analyzer LE-7200/LE-3200 to dedicated analyzer that is specialized for High-speed HDLC communication up to 10Mbps. By installing this OP-FW10 to LE-7200/LE-3200, HDLC measurement processing such as the trigger and filter that were processed by software of the analyzer can be replaced to the hardware processing by FPGA built in the analyzer. Therefore, a maximum speed of HDLC supported is vastly improved. After installation of OP-FW10, You can switch to the usual firmware that supports multi protocol by pressing “SHIFT” and “0” keys at the same time when turning on the power of the analyzer. Therefore, it saves you trouble to reinstall firmware.
