PCI
The Peripheral Component Interconnect Bus is a standard for connecting peripherals to a PC.
See Also: Instrument Control Buses, Modular Instruments, PXI, PXIe, LXI, AXIe, PCIe, GPIB, USB, Ethernet, LAN, miniPCI, CompactPCI, PCI-X, PCI extended
-
Product
PCI Express Mini Card Adapter for PCIe Slots
PCIe-mPCIe
-
The PCIe-mPCIe Adapter is a practical solution for system developers when the target embedded system platform is not yet available, but our PCI Express mini card I/O board is, and you need to get started developing and testing the hardware and software.
-
Product
5 port, PCI Express
PEX 9716
-
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe. Yet ExpressFabric works seamlessly with other standards used within the rack and in rack-to-rack connectivity.
-
Product
PCI High Density Pecision Resistor Card, 6-Channel, 4Ω To 11.4MΩ
50-298-053
Programmable Resistor Module
The 50-298-053 is a high density programmable resistor card with 6 channels which can be set between 4Ω and 11.4MΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Very High Density Multiplexer, 5-Channel, 32-Pole
50-670C-022-5/32
Multiplexer Module
The 50-670C-022-5/32 is a 5-channel, 32-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
Product
12-Port PCI Express
PEX 8748
-
The ExpressLane™ PEX 8748 is a 48-lane, 12-port, PCIe Gen 3 switch device developed on 40nm technology. PEX 8748 offers Multi-Host PCI Express switching capability that enables users to connect multiple hosts to their respective endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
Product
PCI Express 3.0 Test Platform with SMBus Support
Test Platform
The Summit Z3-16 Test Platform with SMBus Support allows the Summit Z3-16 to act as a host emulator, and provides a general purpose test backplane and interposer for testing Gen3, Gen2 or Gen1 hosts and devices. In addition, it supports the Summit Z3-16 with SMBus Support by providing SMBus tapping connectivity.
-
Product
Value-added Module With 4 Antenna Openings And 2 Full-size Rev. 1.2 PCI Express Mini Card Slots
VAM600
-
*4 Antenna openings*Swappable modular design*Maximize I/O flexibility*Designed for tBOX300/500 series*LVD, FCC and EN 50155 certified; CE compliant
-
Product
Single Front Slot + Single Rear Slot Universal PCI To PCMCIA Adapter With Black Bezel
P416B
-
The P416 addresses the need to have front access to a PCMCIA slot for use with cards like Flash media, or Finger Print recognition, while also having a rear slot for cards that are less frequently swapped, like Wireless LAN or Bluetooth. The rear slot is 32-bit capable meaning it supports CardBus cards which makes it forward compatible with some of the newer high speed Wireless LAN standards like 802.11a and 11g.
-
Product
Value-added Module With COM/CAN/DIO And 3 PCI Express Mini Card Slots
VAM900
-
*1 4-wire isolated RS-232/422/485, 1 isolated CANBus 2.0A/B, 1 isolated DIO 8-in/8-out*Swappable modular design*Maximize I/O flexibility*2kV (COM & CANBus)/1.5 kV (DIO) isolated protection*Designed for tBOX300/500 series*EN 50155 certified; CE, LVD and FCC compliant
-
Product
Thin Mini-ITX SBC With Intel® Celeron® Processor N3350, Dual HDMI, LVDS, USB 3.0, PCI Express Mini Card, MSATA And HD Audio
MANO311
-
The MANO311 is powered by the Intel® Celeron® processor N3350 (codename: Apollo Lake). Its customizable I/O interfaces, wide voltage and stunning graphics performance were designed to reduce time-to-market and facilitate quick deployment. The feature-rich MANO311 is an ideal solution for healthcare, automation, retail, digital signage and other Industrial IoT-related applications. The Intel® Atom®-based MANO311 has one 204-pin DDR3L-1867 SO-DIMM socket with up to 8GB of system memory; moreover, it supports 4GB memory down for options. It features one SATA-600 connector, one mSATA socket and one SDXC slot for storage devices. A wide range DC input of 12V to 24V makes the power input selection more flexible for a various applications. Furthermore, the newest mini-ITX motherboard features one PCIe x1 slot and one PCI Express Mini Card slot to enhance its expansion. Triple-display capability is available through the dual HDMI and LVDS.
-
Product
PCI High Density Pecision Resistor Card
50-298-024
Programmable Resistor Module
The 50-298-024 is a high density programmable resistor card with 9 channels which can be set between 2.5Ω and 6.97kΩ with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PCI 24 Channel TTL Digital Interface
8018S
-
The 8018S Low Profile PCI digital I/O interface provides 24 channels of buffered drive digital I/O emulating 8255 mode zero. The board can be utilized for PC-based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems.
-
Product
65 lane, 17 port, PCI Express
PEX 9765
-
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe. Yet ExpressFabric works seamlessly with other standards used within the rack and in rack-to-rack connectivity.
-
Product
PCI Bit Synchronizer
LS-40-P
-
The Lumistar LS-40-P PCI Bit Synchronizer provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digital design assures a consistent product with high reliability and long-term stability. The LS-40-P PCI Bit Synchronizer consists of the LS-40-DB Bit Synchronizer Daughterboard shown below mounted on a PCI carrier board.
-
Product
PCI Digital I/O and Relay Driver Cards
-
a 32-channel Digital I/O card with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel.
-
Product
Digital I/O Card
PCI-DIO-120
-
The PCI-DIO-120, PCI-DIO-96 and PCI-DIO-72 are parallel digital input/output cards designed for use in PCI-Bus computers. The same printed circuit board is used for all three models and is populated for 120 bits, 96 bits and 72 bits respectively. The card is 12.2 inches (310 mm) long and may be installed in any 5-volt PCI slot in IBM and compatible computers.
-
Product
PCI Module
PCI-ECL-II
-
PCI-ECL-II - with Spartan 6 FPGA, 16Mx32 SDRAM, 20 ECL TX , 20 ECL RX, and 12 TTL IO
-
Product
ARINC 429 Multichannel Interface Card for Mini PCI Systems
DAS-429mPCI/RTx
Interface Card
The DAS-429mPCI/RTx is an ARINC 429, multichannel interface card for Mini PCI systems. The card’s small size and suitability for Mini PCI notebook computers, make them a complete solution for developing and testing ARINC 429 interfaces and for performing system simulation of the ARINC-429 bus, both in the lab and in the field.The DAS-429mPCI/RTx is supplied with C drivers, including source code and Mystic application program.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for PCI With 2 Or 4 CAN Bus Nodes
ACP825-x
Simulator
ARINC825 (CAN bus) Test & Simulation module for PCI with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACP825-x PCI card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
PCI-4462, 204.8 kS/s, 118 dB, 3.4 Hz AC/DC Coupled, 4-Input Sound and Vibration Device
779309-01
Sound and Vibration
The PCI‑4462 is a high-accuracy data acquisition module specifically designed for sound and vibration applications. It provides simultaneous four-channel dynamic signal acquisition with six programmable gain settings for making high-accuracy, frequency-domain measurements. The PCI‑4462 also includes software-configurable AC/DC coupling and integrated electronic piezoelectric (IEPE) conditioning to ensure precision measurements with microphones, accelerometers, and other transducers that have very large dynamic ranges. Common applications for dynamic signal acquisition devices include audio test; automotive test; noise, vibration, and harshness (NVH) analysis; and machine condition monitoring.
-
Product
1-Port PCI Express Camera Link Frame Grabber
PCIE-1121
Frame Grabber
Half-Size PCI Express Board Gen 2.0 x4Camera Link clock up to 85 MHzCamera Link Base/Medium/Full/80-BitSupports up to 4 independent camerasSupports PoCL and non-PoCL cameras with SafePowerImage sizes up to 268,435,456 x 16,777,216Independent I/O (trigger, encoder, strobe, etc) for each camera
-
Product
8-CH 12-Bit Isolated Analog Output Cards
PCI-6308 Series
Analog Output Module
- Supports a 32-bit 5 V PCI bus- Isolated 8-CH 12-bit voltage output- 2500 VRMS optical isolation- Jumper selectable bipolar and unipolar output ranges- 4-CH isolated DI and 4-CH isolated DO- Current output version available on PCI-6308A
-
Product
PCI High Density Potentiometer Card 1-Channel, 24-Bit, 0 To 16M Ohm
50-296A-021-1/24
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Express-to-XMC Adapter
4876
-
The Technobox, Inc. P/N 4876 PCI Express-to-XMC Adapter is a development/diagnostics tool that permits the testing of a PCIe card in an XMC site. Up to 8 lanes are supported via the P15 connector. Several activity LEDs located at the edge of the board give an indication of key XMC and PCI Express signals and voltages.
-
Product
Full-Size PCI Express Mini Module With Gigabit LAN
AX92902
-
*Supports 10/100/1000 Mbps transfer rates*Supports Wake-on LAN*Supports PXE Boot ROM*Intel® i210IT controller*51 x 30 mm
-
Product
96/48/24-CH Opto-22 Compatible Digital I/O PCI Cards
PCI-7296/7248/7224
Digital I/O Module
ADLINK"s PCI-7296/7248/7224 are high-density parallel digital I/O boards with 96/48/24 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCI-7296/48/24 can utilize the Opto-22 external devices. The PCI-7296/7248/7224 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCI-7296/7248/7224 provides 4/2/1 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCI-7296/7248/7224 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCI-7296/7248/7224 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
Product
PCI Express To PCI Express Expansion With 16 PCIe X4 Gen-2 Slots
ExpressBox16-BX4
-
Magma’s ExpressBox 16 is the simplest solution to seamlessly increase the number of PCI Express® slots available to your server or workstation. ExpressBox 16 expands one host PCIe® slot to sixteen slots by extending PCI Express signals over a high-bandwidth x8 or x16 connection to an external Magma enclosure.
-
Product
16-Lane, 5-Port PCI Express
PEX 8718
-
The ExpressLane™ PEX8718 is a 16-lane, 5-port, PCIe Gen3 switch device developed on 40nm technology. PEX8718 offers PCI Express switching capability that enables users to connect a host to the endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
Product
XMC-to-PCI Express (PCIe) Adapter
8613
-
Our Reverse Compact XMC-to-PCI Express (PCIe) Adapter 4X (8613) permits use of a standard VITA 42.3 air-cooled XMC, or VITA 20 conduction-cooled XMC, in the smallest possible edge finger PCI Express form factor. The length of the adapter is the length of the XMC, and 10 mm mezzanine stacking height is supported.
-
Product
Packet Analysis Probe for PCI Express
N4220A/B
-
When purchased with a logic analyzer, the application software you order is installed on the instrument hard drive. If you need to add application support after your initial logic analyzer purchase or are controlling a logic analyzer from a host PC, you must install the appropriate software before you can make measurements.
