PCI
The Peripheral Component Interconnect Bus is a standard for connecting peripherals to a PC.
See Also: Instrument Control Buses, Modular Instruments, PXI, PXIe, LXI, AXIe, PCIe, GPIB, USB, Ethernet, LAN, miniPCI, CompactPCI, PCI-X, PCI extended
-
product
PCI CONET Controller
A2818
The Mod. A2818 is a 32-bit 33 MHz PCI card, which allows the control, through a standard PC, of up to 8 CAEN Optical Slave Cards (CAEN VME Bridge or Digitizers). The communication protocols used are the CONET1 or the new CONET2 (A dedicated firmware for the desired protocol must be installed on the board).
-
product
PCI/PCIe-Based Serial Communications Cards
PCI-C588/PCI-C584/PCIe-C588
- IRQ & IO address automatically assigned by BIOS- Supports up to 2 cards per system, jumper-less, easy to configure- Isolated RS-422/RS-485 interface (C422/C485, C518/C514)- PCI Rev 2.1 Plug-and-play- PCI Express® x1 compliant (PCIe-C588)
-
product
PMC to PCI Express Adapter w/ TSI384
8636
The Technobox, Inc 6083 4-lane and 8638 1-lane carrier card allows use of a PMC in a PCI Express edge card slot. The product features an IDT TSI384 bridge IC used in transparent mode with a PCI Express primary side and a PCI/PCI-X secondary side.
-
product
ARINC 429 Test & Simulation Interface for PCI Express
PCIe-C429
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
3U Rackmount Appliance for PCI Express® Gen5
R300-G5 Pro
Is a robust, versatile test system designed to test and debug solid state drives (SSDs) of all popular storage interfaces and protocols.
-
product
PCI High Density Pecision Resistor Card, 4-Channel, 3Ω To 102kΩ
50-298-134
The 50-298-134 is a high density programmable resistor card with 4 channels which can be set between 3Ω and 102kΩ with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
ARINC 429 Test And Simulation PCI Module
PCI-C429
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
Squid PCI Express Carrier Boards™ for MiniPCI Express Modules
Amfeltec Squid PCI Express Carrier Boards™ for MiniPCI Express Modules
-
product
Fanless Embedded System With Intel® Celeron® Processor N3160, VGA, HDMI, 4 COM, 2 GbE LAN, 4 USB, 2 PCI Express Mini Card Slots And 9 To 36 VDC
eBOX626-853-FL
The eBOX626-853-FL is a slim-type fanless embedded system with wide range temperature and wide range DC input support. The cost effective compact embedded box PC is designed to support the Intel® Celeron® processor quad-core N3160 (codename: Braswell) integrated with Intel® Gen 8 graphics and DirectX 11.1. One DDR3L 1333/1600 SO-DIMM socket supports up to 8 GB memory. The IP40-rated industrial computer eBOX626-853-FL combines low power consumption with high performance graphics and computing for smart automation, transportation, industrial gateway, multiple media kiosk and other IoT&M2M applications.
-
product
PCI High Density Pecision Resistor Card, 6-Channel, 3.5Ω To 1.51MΩ
50-298-044
The 50-298-044 is a high density programmable resistor card with 6 channels which can be set between 3.5Ω and 1.51MΩ with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCI Express, Analyzer Software Included, IEEE 488 GPIB Instrument Control Device for Windows - Low Profile, Onboard GBIP Analyzer
780936-01
The PCIe‑GPIB+ combines an IEEE 488 controller and an analyzer on one device for computers with PCIe slots. You can use this device to integrate an instrument into your system using GPIB as well as to troubleshoot and solve GPIB hardware and software problems. The PCIe‑GPIB+ achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
PCI High Density Pecision Resistor Card, 9-Channel, 3Ω To 102kΩ
50-298-034
The 50-298-034 is a high density programmable resistor card with 9 channels which can be set between 3Ω and 102kΩ with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCI 4-Channel Precision Resistor Card
50-297-102
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
32-bit PMC to PCI Adapter
8092
This PMC to PCI Adapter permits delivery of PMC-derived applications in a standard PCI environment. Mechanically, a PMC card fits cleanly on a short-length PCI board, resulting in a highly acceptable delivery solution for desktop applications.
-
product
IEEE-488 GPIB Device Interface IC (Chip) for the PCI-Bus
GPIB-72120
The i72120 GPIB-Chip is the ideal solution to implement a IEEE488.2 GPIB interface for next generation PCI based instruments. The GPIB-ASIC is designed to meet all of the functional requirements for talker and listener (TL) devices as specified by the IEEE Standards 488.1-1987 and 488.2-1987. Connected between the PCI bus and the GPIB, this GPIB-IC provides high-level management of the GPIB to unburden the processor and to simplify both hardware and software design. The i72120 is fully compatible with the PCI specification and requires only the addition of bus driver/receiver components to implement a talker/listener GPIB interface.
-
product
Low-Profile 16-CH Isolated DI & 16-CH Isolated DO PCI Card
LPCI-7230
ADLINK LPCI-7230 is 32-CH isolated input and/or card. It provides a 2,500 C optical isolation protection. Two wide input range of the LPCI-7230 makes it easy to sense the status of external devices. The non-polarity characteristic is suitable for a wide variety of industry applications. The LPCI-7230 devices also feature a wide output range from 5 to 35 V, which is suitable for relay driving and industrial automations applications. The LPCI-7230 also provides two interrupt sources on digital input channels, which are easily user configurable.
-
product
PCI-X Carrier For AMC Modules
PCI102
The PCI102 allows testing of AMC.1, AMC.2 and AMC.3 modules in a PC environment during development and manufacturing; reducing the costs associated with maintaining different platforms. The PCI101 is a PCI-X edge style carrier with PCIe x4 lanes going to the AMC module. The AMC.1 module connects to the host PC’s PCI-X bus via a PCI-X to PCI ebridge. The AMC.2 module’s GbE ports are routed to RJ-45s. The AMC.3 differential pairs are routed to two SATA connectors. ThePCI102 is available with an optional VT001 IPMI controller which can test the AMC IPMI management functionality. The dual I2C bus connectors allow for connecting any I2C bus to any other I2C bus as well as being able to debug and monitor the I2C bus traffic. Provides two current sense resistors to measure the payload power as well as the management power of the AMC. The PCI102 can be powered on the bench without the host PC.
-
product
IRIG Time Code Receiver & Generator for Computers (PCI Express)
TCR180PEX
Meinberg Funkuhren GmbH & Co. KG
The TCR180PEX receives IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes and can be used for synchronizing the system time of its host PC. The IRIG output of this card can generate an IRIG signal for other IRIG time code readers. The output format is independent from the incoming IRIG signal - a perfect solution to your IRIG conversion requirements. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements) or as an IRIG converter device.
-
product
PCI Card with input channels
PCI_LVDS_8R
The PCI_LVDS_8R has 8 channels of LVDS input. The channels are grouped two per Filter Xilinx. The input data is filtered, then written to the Input FIFO. There is one Input FIFO per LVDS channel. 1K x 32. One Latch Xilinx handles 4 LVDS channels. The data is read from the Input FIFO by the Latch Xilinx and either written to the SDRAM or the Output FIFO.
-
product
PCI, IEEE 488 GPIB Instrument Control Device for Windows
778032-01
The PCI‑GPIB is a plug‑and‑play IEEE 488 interface for PCs and workstations with PCI expansion slots. The PCI‑GPIB can sustain data transfer rates of more than 1.5 MB/s using the IEEE 488.1 three‑wire interlocked handshake. It also implements the high-speed IEEE 488.1 noninterlocked handshake (HS488) for benchmarked data transfers at more than 7.7 MB/s. The onboard bus master DMA controller means that there are no microprocessor interruptions in data transfer.
-
product
Low Profile PCI Express 1-Port
7106e
The 7106e low-profile PCI Express serial interface provides a single serial port configurable for RS-232, RS-422, RS-485 or RS-530. The ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allows the adapter to support the widest range of standard and non-standard baud rates exceeding 921.6 K bps. These features make the 7106e ideal for data intensive applications that require reliable, ultra-fast throughput rates.
-
product
2-port/4-port PCI Express 1GigE PoE Card with M12 X-
AX92325
Four M12 x-coded connectors with special design (to avoid occupying two slots) 2 or 4 independent Gigabit PoE ports, Supports 9.5KB Jumbo Frame and IEEE 1588, Compliant with IEEE802.3at to deliver 30W at 54 VDC per port, PCI Express x4 compliant
-
product
PCI Resistor Card 2-Channel 1.5 Ohm To 4.09k Ohm With SPDT
50-293-123
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Low Profile PCI Express 2-Port
7205ec
The 7205ec low-profile PCI Express serial interface provides two serial ports configurable for RS-232, RS-422 or RS-485. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates exceeding 1 Mbps. These features make the 7205ec ideal for data-intensive applications that require reliable, ultra-fast throughput rates.
-
product
PCI Express System Timer (USB Interface)
SKU-032-01
The MiniPCI Express System Timer uses a standard USB interface to synchronize IP signals. This system timer provides accurate clock timing for Asterisk® open-source PBX software.
-
product
75 Ohm 1.6/5.6 to 1.6/5.6 Cable Assembly
40-977-791-1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
Fanless Embedded System With LGA1151 9th/8th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, 4-CH PoE And MXM 3.1 Type A
eBOX671-521-FL
The eBOX671-521-FL is a GPU computing embedded system that comes with 4-CH PoE and MXM 3.1 Type A slot for applications in machine vision, edge computing, traffic vision, deep learning, and artificial intelligence of things. The outstanding eBOX671-521-FL with enhanced GPU computing performance is powered by the 9th/8th gen Intel® Core™ i7/i5/i3 processor with up to six-core, Intel® Pentium® processor, or Intel® Celeron® processor and comes with Intel® Q370 or optional Intel® C246 chipset. The fanless embedded GPU-based system is equipped with dual DDR4 ECC/non-ECC SO-DIMM slots for up to 64GB of system memory. The embedded vision system has an optional MXM type A slot for NVIDIA GTX1030 and GTX1050 graphics modules to enhance the performance of the visual display. Furthermore, this Intel® Coffee Lake-based embedded box PC is specially designed with four Gigabit 802.3at (PoE, Power-over-Ethernet) compliant Ethernet ports with a total power budget of 60W, six USB 3.1 ports and two Gigabit LANs to connect different devices or sensors. It comes in great expansion possibilities, including one internal MXM 3.1 type A connector, two full-size PCI Express Mini Card slots and two SIM slots. For storage, it has two swappable SATA HDD drive bays with a height of up to 9.5 mm and one mSATA for RAID 0 and 1 feature. Besides, we have designed a flexible I/O window slot for incorporating application-oriented I/O functions to meet the requirements of various cases. This embedded vision computer can be mounted using wall or DIN-rail mounting for versatile use in various environments.
-
product
Bit Waveform Digitizer
ATS9351
ATS9351 is a low-noise, 500 MS/s 12 bit PCI Express waveform digitizer designed for OEM customers. With fixed input range of +/- 400 mV and signal to noise ratio in excess of 61 dB, ATS9351 is an ideal solution for swept-source OCT applications.
-
product
Mini-ITX SBC With AMD G-Series APU, AMD A55E, HDMI/VGA/LVDS, Dual LANs And SATA-600
MANO120
The MANO120, a graphics-rich Mini ITX motherboard is based on the new AMD G-Series APU dual core T56N with AMD A55E FCH. Integrated with Radeon™ HD 6320 graphics with DirectX 11 technology, the MANO120 offers advanced 3D graphics and dual views via VGA and HDMI connection on the rear I/O, as well as onboard 18 bit single channel LVDS interface. The onboard SO-DIMM socket supports up to 4 GB of DDR3 1333 memory. It also has a wide range of storage with five SATA-600 ports and a mainstream CFast™ slot. To satisfy expansion capability requirement for industrial application needs, the MANO120 comes with one PCIe x4 slot and one PCI Express Mini Card slot. With advanced performance in both computing and graphics, this industrial grade motherboard meets the requirement of system developers in the gaming, digital signage, DVR, and NVR.
-
product
PCI Resistor Card 2-Channel 2 Ohm To 32.7k Ohm
50-293-032
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
