-
Product
6U CompactPCI Enclosures & Systems
-
1~9U CompactPCI chassis for 6U CompactPCI boards , most of which are with front/rear panel I/O, H.110 CT bus and redundant power supplies.
-
Product
CompactPCI Chassis 3 Slots
1U 84HP
-
Hartmann CompactPCI 1U system platform provides an intelligent, practical packaging solution for high-performance processors. The full width rack mount model provides a 3 slot 5V I/O 3U cPCI backplane for horizontal mounting of boards. This system is designed with enhanced EMC features.
-
Product
CompactPCI/PlusIO/Serial
-
ADLINK provides a complete line of 3U and 6U CompactPCI platform and along with a diverse line of plug in boards and these CompactPCI products provide the most cost-effective high performance platforms for telecommunications, military , industrial automation.
-
Product
CompactPCI Serial 3U Backplanes
-
Hartmann Electronic’s cPCI Serial Backplanes are compliant to PICMG CPCI S.0 CompactPCI Serial specification. These backplane are outfitted with a cPCI S.0 system slot for the CPU on either the left or right side and then have up to eight CPCI S.0 peripheral slots.
-
Product
16 Channel ADC for CompactPCI
CPCI392
-
The CPCI392 16-Channel Common-Mode Input ADC card is very well suited to be used in applications in which autonomous signal conversion is an issue, as well as in standard mid-range applications. Enabled channels are scanned at maximum rate and conversion results are stored in shared memory. A local DSP performs the data acquisition and calibration transparent for the host.
-
Product
CompactPCI 2 Slot 1U
-
1U, 19″ Rackmount system with hot removable CPCI 3U Power Supply, four Powerful Fans and CompactPCI Backplane. The system support 6U cards Front and Rear. Additional four fans are available for optimal Front and RTM cooling solution. The Backplane is compliant with PICMG 2.0 R3.0 with 64bit 66MHz & supports boards with hot swap capability PICMG 2.1 R2.0. All five CompactPCI connectors (J1-J5) are available on the backplane. The system slot is located on the lower-slot.
-
Product
3U CompactPCI Serial Blades
-
The PICMG CPCI-S.0 CompactPCI Serial standard, which evolved from the PICMG 2.0 specification, is the fastest, most versatile, most cost-effective open standard for CompactPCI (CPCI). The Serial standard is mechanically and electronically compatible with 3U and 6U euro-cards, defining an interface for high-speed switched fabrics with a star topology. Point-to-point connectors allow up to eight peripherals on one system slot without switches or bridges. Ethernet data transfer can be configured with full mesh topology, which allows up to 1000Base-T connections to all peripheral slots for redundant, safety-critical systems.
-
Product
CompactPCI Chassis
-
CompactPCI is a standard in computer bus technology for industrial computing that utilizes a Eurocard type connector combined with PCI signaling and protocols. cPCI boards come in 3U and 6U variants and are typically interconnected through a passive backplane. The connector pin assignments are standardized by PICMG , allowing for eight boards in a PCI segment with multiple bus segments being allowed with the use of active bridges.
-
Product
CompactPCI Serial 3U Backplanes / Power connector
-
Hartmann Electronic’s cPCI Serial Backplanes are compliant to the PICMG CPCI S.0 CompactPCI Serial specification. This backplane features 1 power slot in addition to either 6 or 9 cPCI serial slots.
-
Product
CompactPCI Card
IIB-429-CPCI
-
The IIB-429-CPCI provides from ARINC-429 compatible channels (2 receive and 2 transmit) at any rate between 12.5 and 100 kbps. Because the IIB-429-CPCI is built upon a flexible platform, user function can be implemented almost without restriction, making this product flexible and user-friendly. This CompactPCI card has a 3U form factor. This unit is also available in a 6U form factor (IIB-429-CPCI-4C) with four times the functionality
-
Product
6U CompactPCI Switches
-
CompactPCI Switches 6U or 3U managed Gigabit Ethernet switch blades.
-
Product
6U CompactPCI Multifunction I/O Board
CPCI-MFIO-6U
-
The CPCI-MFIO-6U is a 6U CompactPCI multifunction I/O board. The CPCI-MFIO-6U offers 32 channels of 16 bit A/D, four 16 bit D/A, 16 digital I/O, counter / timers, and one PMC expansion slot for additional I/O. There is a local 60 Mhz TMS320C31DSP processor to supervise all the I/O activity. The DSP can be programmed by the end user to execute application specific code. The CPCI-MFIO-6U is ideally suited for factory automation, automatic test equipment, test & measurement, and control systems.
-
Product
CompactPCI Serial 8 Slot 9U
-
The CompactPCI® Serial backplane is designed to be used with CompactPCI Serial 9 Slot 4U chassis.
-
Product
6U CompactPCI
-
Advantech offer 6U CompactPCI CPU boards, rear transition modules, peripheral boards, and support for PMC or XMC module.
-
Product
3U CompactPCI Serial FPGA 10-20 ports Industrial Ethernet
SY7-CYCLONE
-
The EKF SY7-CYCLONE is a CPCI Serial FPGA board with front panel connectors for up to 20x100Mbps SPE ports. It can be configured as Ethernet NIC, switch, router, or gateway.
-
Product
3U CompactPCI
-
Advantech offers one-stop services for 3U CompactPCI solutions including CPU boards, I/O boards, system integration and customization services.
-
Product
3U CompactPCI Serial 2.5" SATA Storage Carrier
cPCI-A3H10
-
- 3U 4HP CPCI-S.0 peripheral- One 2.5" SATA 6Gb/s drive slot- Status LEDs on faceplate: drive activity, hot-swap status, user-configurable- Hot swap support- Operating temperature: -40°C to 85°C with qualified com
-
Product
Stepper Motor Controller for CompactPCI
CPCI321
-
The CPCI321 Intelligent Stepper Motor Controller with amplifiers is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead.
-
Product
3U Format CompactPCI (CPCI) Bus IP Carrier
CPCI-SIP-2
-
The CPCI-SIP is a 3U format CompactPCI (CPCI) bus IP carrier. The CPCI-SIP-2 provides mechanical support and the electrical interfaces for two single width IP modules, or a double width IP module. Multiple CPCI-SIP-2 boards may be installed in a single system.
-
Product
PMC Carrier for 3U CompactPCI
TCP270
-
The TCP270 is a standard 3U CompactPCI carrier that provides front I/O and rear I/O for a single width PMC module. This PMC to 3U CompactPCI adapter is used to build modular, flexible and cost effective I/O solutions with PMC devices in CompactPCI systems.
-
Product
CompactPCI 6U 64 bit ATX 8 slot, P1s P2l, RoHS
102CPCI608-40X0R
-
CompactPCI 6U 8 slot 64 bit low Easycable, system slot left, with ATX connector. It is fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
3U CompactPCI Serial 5-slot SSL w/ RTM w/ Ethernet
1CPCIS-305-L210
-
3U CompactPCI Serial Backplane with 5 CompactPCI S.0 slots, system slot left, with rear IO : 1x CompactPCI S.0 CPU slot, 4x CompactPCI S.0 peripheral slots, with connectors for RTMs (RearTransition Modules) in slots 2 to 5, Ethernet full mesh.
-
Product
3U CompactPCI Serial 9th Gen Intel Xeon®/Core™ i7 Processor Blade
cPCI-A3525 Series
-
CompactPCI® Serial (PICMG CPCI-S.0) is a new modular computer standard officially adopted by PICMG in 2011. The CompactPCI Serial standard defines a completely new connector to support high-speed serial interfaces including PCI Express, SATA, USB and Ethernet. A CompactPCI Serial backplane has six high-speed connectors P1 to P6 on the system slot but only P1 is mandatory on peripheral slots, P2 to P6 being optional. A CompactPCI Serial system can comprise a total of nine blades (one system blade and eight peripheral I/O blades) through an Ethernet full mesh or single star architecture. The CompactPCI® Serial standard is the next-generation of the CompactPCI® specification and provides more flexibility and higher speed and bandwidth in modular system solutions.
-
Product
3U CompactPCI Serial 6-slot SSL w/o RTM w/ Ethernet
1CPCIS-306-L200
-
3U CompactPCI Serial Backplane with 6 CompactPCI S.0 slots, system slot left, without rear IO : 1x CompactPCI S.0 CPU slot, 5x CompactPCI S.0 peripheral slots, without connectors for RTMs (RearTransition Modules), Ethernet full mesh.
-
Product
3U CompactPCI Serial Vector FlexRay CAN LIN Module Carrier
SFV-RAY
-
The SFV-RAY is a 3U CompactPCI Serial carrier card for the Vector VN7610 and similar Vector FlexRay/CAN-FD compact interfaces. On-board USB controller. Can be installed in any peripheral slot of a CPCI Serial backplane.
-
Product
14-Slot 32-Bit 6U CompactPCI H.110 Bus Backplane
cBP-6014R
-
- PICMG 2.0 CompactPCI Specification R3.0 Compliant- PICMG 2.1 CompactPCI Hot Swap Specification R2.0 Compliant- PICMG 2.5 H.110 Computer Telephony Specification R1.0 Compliant- PICMG 2.7 Dual system Bus specificationR1.0 compliant- One system slot with 13 expansion slots, system on the middle slot of the backplane
-
Product
3U CompactPCI Serial 2-slot SSR w/o RTM w/ Ethernet
1CPCIS-302-R200
-
3U CompactPCI Serial Backplane with 2 CompactPCI S.0 slots, system slot right, without rear IO : 1x CompactPCI S.0 CPU slot, 1x CompactPCI S.0 peripheral slots, without connectors for RTMs, Ethernet full mesh.
-
Product
CompactPCI 6U 64 bit ATX 8 slot, P1s, P2-5l, RoHS
102CPCI608-4057R
-
CompactPCI 6U 8 slot 64 bit low Easycable, system slot left, with ATX connector. It is fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
CompactPCI 6U 4 Slot right justified, 64 bit, P1-2s, P3-5l
105CPCI604-1157
-
CompactPCI 6U 4 slot 64 bit with system slot right, fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1. User defined VI/O is standard.
-
Product
6U CompactPCI Boards
-
Full line of 6U CompactPCI products supporting PICMG 2.16, IPMI, Hotswap, TPM, System Management.
