-
product
Wheel Torque Transducer
WTT-Dx
In automotive development, it is important to know the exact torques acting on the vehicle – especially under acceleration and braking maneuvers. With the WTT-Dx wheel torque transducer, a high-precision tool is available for making such measurements. The WTT detects the mechanical load directly where it is produced: the wheels that form the interface between the vehicle and the road.
-
product
Pressure Transmitters
Pressure Transducers and Industrial Pressure Transmitters provide an advanced alternative for users looking for continuous pressure measurement as opposed to a simple on-off switch. Our full line of pressure transducers provide a wide range of pressure ranges from -14.5 psig to 30,000 psig allowing for a highly diverse operating profile for any end user. Our transducers offer output signals including 0-5V, 0-10V, 1-5V, 0.5-4.5V (ratiometric), 4-20mA and others. Additionally, these can be customized with a diverse selection of fittings and electrical connectors including both integral and external connections.
-
product
Singlebeam Hydrographic Echosounders
Teledyne Marine Odom Hydrographic
Odom Hydrographic provides an extensive range of hydrographic level single beam echosounders with the flexibility of frequency agility supporting existing transducer installations. Models include modern PC screen based interfaces as well as support for tried and tested thermal record printing.
-
product
LVDT to Digital-RVDT to Digital Converters
Computer Conversions Corporation
LVDT Displacement transducers accurately measure position and displacement. The strength of the LVDT is in its principle of operation. As LVDT sensors are inductive, there is no electrical connection across the sensor, which ensures clean, accurate data and a long life.
-
product
Transducers
Is a unit which comprises a preamplifier fed by a constant current ICP and a condenser microphone
-
product
High Accuracy AC Reference Source
515
Clarke-Hess Communications Research
The Model 515 High Accuracy AC Reference Generator fills a need for a relatively low cost and practical solution for supplying a reference excitation to typical LVDT and Synchro/Resolver transducers. The Model 515 has built-in load sensing which, in effect, yields "zero" output impedance and virtually eliminates the effects of fluctuating output loads. With up to 15 VA of output into loads with as much as 80 of phase shift, the Model 515 is ideally suited to driving inductive loads.
-
product
High Speed Data Acquisition
Data acquisition (DAQ) is the measurement, recording, analyzing, and presentation of real world phenomena. It includes electrical measurements such as voltage, current, power as well as measurements through sensors and transducers including temperature, pressure, flow, level, strain, acceleration, vibration, humidity, and more.
-
product
Advanced Clamp-On Ultrasonic Flowmeter
KATflow 150
The KATflow 150 is the premier product for flexibility and performance, providing the user with a comprehensive specification and a list of configuration options. The practical modular design and the wide variety of different transducer types available ensure this instrument is suitable for everything from simple water flow measurements to energy flow monitoring and automated process control.
-
product
Ultrasonic Flowmeter
F8
Gentos Measurement & Control Co.
The F8 Flow meters is a state-of-the-art universal transit-time flow meter for heavy industrial applications. Sophisticated electronics incorporating the latest developments in digital signal processing coupled with powerful ultrasonic transducers deliver highly accurate flow measurement for liquids in full pipes.
-
product
Condition Monitoring
m+p Coda is a versatile monitoring system that captures and records signals coming from sensors such as accelerometers, thermocouples, strain gauges, and pressure transducers. Limit checking and alarm monitoring is provided for every active channel. The active channels are clearly displayed in a separate window, out-of-limit data can be seen at a glance. Alarm events are entered into a log file and can be reviewed at any time. You have the option to change the alarm limits online at any time without stopping the data acquisition.
-
product
Voltage Meter
MDN8I
MDN8I is a mezzanine module designed for high-precision measurements in dynamic signal analysis systems, as well as for joint work with ICP sensors and vibration transducers with a charge output (force sensors, dynamic pressure, acoustic emission, vibration displacement, etc.). The MDN8I mezzanine module has electrical characteristics no worse than those of most foreign and domestic counterparts, and in some parameters exceeds them.
-
product
LVDT to Digital and RVDT to Digital Converters
Computer Conversions Corporation
LVDT Displacement transducers accurately measure position and displacement. The strength of the LVDT is in its principle of operation. As LVDT sensors are inductive, there is no electrical connection across the sensor, which ensures clean, accurate data and a long life.
-
product
Charge Amplifier
ZET 440
Charge amplifier ZET 440 for piezoelectric detectors is intended for:*amplification and conversion of output signals of primary piezoelectric transducers with charge output;*amplification and conversion of output signals of primary transducers with the IEPE type in-built electronics to voltage;*gain ratios: 1, 10, 100;*LPF: 0.1, 1, 10 Hz
-
product
Digital Strain Gauge Sensor
ZET 7111
The ZET 7111 module is intended for measuring the relative deformation using primary transducers based on tension gauges. These may be either assembled tension gauges (force gauges, torque gauges), or separate external tension gauges connected using half-bridge or bridge scheme.
-
product
Auto Reversing Run Down Adapters
AURA
The AURA auto reversing run down adapters are designed to provide consistent and reliable torque readings for use with power driven torque control tools. The AURA reduces the impact and irregular peaks that cause poor repeatability. The run down adapter is mounted in-line between the tool drive and transducer.
-
product
Altitude Indicator and Pressure Transducer
AI100
Bemcos AI100 Altitude Indicator and Pressure Transducer provides a red, 5-digit scaled LED display of chamber or process Altitude, calibrated in feet or meters as well as a linear, scaled output of 4 to 20 mA, 0 to 5 VDC, or 0 to 10 VDC for use with other instruments including process controllers, recorders, and programmable logic controls.
-
product
Axial Extensometer
Model 3542
Jinan Testing Equipment IE Corporation
These extensometers are designed for testing a wide range of materials, including metals, plastics, composites and ceramics. All will work in both tension and compression. The dual flexure design makes them very rugged and insensitive to vibrations, which permits higher frequency operation.They come standard with Epsilon’s quick attach kit, making it possible to mount the extensometer on the test specimen quickly and easily with one hand. The quick attach kit can be removed, allowing mounting of the extensometer with springs or rubber bands.The Model 3542 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.For gauge lengths 100 mm (4 inches) or greater see Model 3542L.
-
product
General Purpose Basic Carrier Demodulator
CD15
The CD15 Sine Wave Carrier Demodulator operates with variable reluctance transducers to provide a DC output signal for dynamics as well as steady state measurements. A 5kHz sine wave excitation is applied to the two inductance ratio arms of the transducer and the resulting output is demodulated and amplified using the latest integrated circuit techniques. The DC output is obtained from an active filter circuit and gives a uniform response from steady state to 1000 Hz. The low impedance sine wave excitation allows operation with the transducer located over 1,000 feet from the CD15.
-
product
Miniature Pressure Transducer
EPT1200
The EPT1200 series of Pressure transducers has a miniature design using a hermitically welded, thin filmmeasuring cell, coupled with high level output circuitry. This technology ensures this sensor is suitable for some of industries harshest environments, including automotive, industrial hydraulics, refrigeration, off-road, construction and agricultural applications. The EPT1200 and 1500 series offer measurements in gauge and absolute pressure, with ranges up to 400 Bar and are backed by a one-year warranty.Miniature design | Rugged construction | Wide operating temperature range | Long life High performance
-
product
Load Cell Transducer
Unitech Scales And Measurements Pvt. Ltd
Force can be measured by different methods, one of the most effective and accurate method is by using strain gauge based load cells. Four Transducer class strain gauges are bonded on the specimen and are connected in the form of Whetstone Bridge. The specimens are of different types depending on the requirement such as S, column, beam, ring, shear beam, binocular etc. UNITEH’S Load Cells are used for wide applications rite from commercial weighing scale to industrial process controlling, R & D applications and educational institutions. UNITECH’S manufacture load cells from 1Kg to 100Tons for compression or tension or universal (Compression and tension) applications. We also undertake custom built load cells for specific requirement and for OEM users.
-
product
Handheld Ultrasonic Flow Meter for Liquid
P117
Gentos Measurement & Control Co.
P117 is a hand-held flow meter equipped with external clip-on transducers, which can meet the needs of convenient and fast flow measurement, allowing you to quickly transfer and measure data between different working environments and improve work efficiency.
-
product
PVdF Transducers
PVdF transducers have a wide bandwidth, short impulse response and can be designed to your specific requirement.
-
product
DC Source/Calibrators
Our DC Source/Calibrators are designed for a typical applications such as the design, check and calibration of high speed, high resolution A/D converters; design and certification of high speed data logging and process control systems; calibration of digital voltmeters and multimeters; as an “IMBEDDED STANDARD” and/or simulator; design, testing, simulation and certification of thermocouples, strain gages and transducer instrumentation.
-
product
Quick Change Probes For Weld Seam Testing (ASTM)
SONOSCAN Q
In addition to angle beam probes according to european standards (EN), we offer probes with quick-change wedges for ultrasonic weld seam inspection as well as various wedges for the american market. Quick-change probes are used wherever access to the inspection object is difficult to reach with the larger AWS transducers. The relatively small, round elements also offer better defect resolution.
-
product
Phase Angle and Power Factor Transducer of Single-phase AC Electric Power
NMTFi
The NMTFi device is a phase angle and power factor transducer operated in single-phase power network and featuring two independent analogous outputs. The A output measures the phase angle between voltage and current, the B output measures the power factor. In such a was one single NMFTi transducer is able to replace two customary transducers thus making it possible to achieve significant savings in installation space.
-
product
Rod and Barrel Style (BLOK) LDT
AMETEK Sensors, Test & Calibration
The Rod and Barrel Style LDT – BLOK - Housing is designed for applications where mounting a standalone Rod or Profile Style Linear Displacement Transducer, is prohibitive. This housing style adds a chamber, magnet and piston. The aluminum extrusion houses the sensing element and electronics.
-
product
PXIe-4339, 25 kS/s, 24-Bit, 8-Channel PXI Strain/Bridge Input Module
783531-01
25 kS/s, 24-Bit, 8-Channel PXI Strain/Bridge Input Module—The PXIe‑4339 is a universal bridge input module ideal for test cell installations requiring both accuracy and flexibility. Completely configurable through software, each channel can take bridge-based measurements and direct voltage measurements. Eight input ranges in ratiometric mode and four in voltage mode accommodate a wide variety of sensor types for your changing application needs. The PXIe‑4339 also features per-channel wide bandwidth analog outputs, programmable excitation, Transducer Electronic Data Sheet (TEDS) support, and digital filtering.
-
product
Fiber Optic Strain Sensors
Opsens Solutions optical strain sensor delivers reliable results in harsh environment. Opsens Solutions OSP-A fiber optic strain transducers are designed to provide accurate deformation measurement in the most adverse conditions. Its small size and EMI/RFI electromagnetic environment and lightning immunity makes it the ideal sensor for geotechnical, structural health monitoring, Defense and aerospace and general applications.
-
product
Acoustic Emission Transducer
GT301
Acoustic emission transducer GT301 converts acoustic signal into electrical signal, parameters of which are used for acoustic emission source evaluation.
-
product
Circuit Breaker Analyzers & Timers
CAT Advanced Series
DV Power circuit breaker analyzer and timer utilizes the latest technological enhancements for safe and fast testing of circuit breakers. The sophisticated design ensures efficient and reliable operations in high-voltage substations and industrial environments.The CAT Advanced series are stand-alone or PC-controlled digital instruments for a circuit breaker testing. The timing channels record closing and an opening of the arcing, resistor, and auxiliary contacts. Also, the main contact channels can measure the resistance value of the pre-insertion resistors (if present in the circuit breaker).With CAT Advanced series instruments, it is possible to record graphs of open and close coil currents. Furthermore, it records displacements of the HV and MV circuit breaker moving parts. Test results can be saved via USB, PC or be printed via 112 mm (4.4 inches) thermal printer (optional accessory) in tabular and graphical form.A circuit breaker test consists of different operational modes and CAT Advanced series supports:Open (O)Close (C)Reclose (O-0,3s-C)Trip free (CO)O-0,3s-COOpen-Close (O-C)Close-Open (C-O)Open-Close-Open (O-C-O)First trip (O)Multiple operations, such as Open-Close and Open-Close-Open, can be initiated by using a predefined delay time or by sensing a breaker’s contact position.The auxiliary inputs are used to monitor dry and wet auxiliary contacts. The six coil control analog channels measure and record coil currents simultaneously (OPEN and CLOSE), up to 35 A AC/DC.The additional six voltage analog channels have four selectable voltage ranges available (±1 V, ±5 V, ±60 V and ±300 V AC/DC).A built-in micro-ohmmeter generates up to 500A true DC ripple-free current with an automatically regulated test ramp that provides performing static and dynamic contact resistance measurement.Three transducer channels provide a measuring displacement of the circuit breaker moving parts, contact wipe, over-travel, rebound, damping time and average velocity. Also, a user can connect either an analog or a digital transducer to these universal channels.
