-
product
General Purpose Pressure Transducer and Transmitter
P55
The robust P55 pressure transducer provides cost-effective reliability for severe test environments. With extreme resistance to shock and vibration, the P55 pressure transducer delivers the same high-level performance expected from more delicate differential pressure transducers and pressure transmitters. With variable reluctance sensing technology, the P55 pressure transducer delivers fast dynamic response, high resistance to vibration and superior signal stability through ambient temperature change for a wide variety of low-pressure to high-pressure measurements. The P55 pressure transducer will accept both liquids and gases directly at the sensing diaphragm and there are no internal isolation fluids to slow the sensor response or cause excessive temperature drift errors.
-
product
Advanced Monitoring Probe
DVB-C QAM
Combined with a Network Monitoring System or not, the EdgeProbe Advanced provides a powerful broadcast network alert & diagnosis tool allowing DTV network operators to monitor global trends and anticipate potential failures.EdgeProbe Advanced is able to monitor DVB-C and DVB-C2 signals at transmitter outputs, through its RF inputs (up to 4 in 1RU), as well as at modulator input and at Head-End/distribution links, through its ASI and IP inputs.
-
product
Multifunction Calibrators
These bench multifunction calibrators source, simulate, and measure pressure, temperature, and electrical signals with exceptional precision. They can automate calibration procedures and maintain a wide range of temperature and pressure transmitters, multi-meters, pressure gauges, and more.
-
product
FM Tokenless Transmitter & Receiver
MS 1522
Transmitter and Receiver units are designed to work at 24V DC voltage (nominal) with variation between 19.2 V to 28.8V. The system is designed to work with carrier frequency 1800/2700 Hz and modulated frequency 65Hz/85Hz. For 1800Hz Carrier Frequency RED border is used in Front Panel and for 2700Hz Carrier Frequency BLUE border is used in Front Panel. Maximum power consumed by transmitter and receiver are 1.2W and 8W, respectively. Sense level for receiver is less than –19 dBm and No sense level for receiver is more than –22 dBm with 1mw (0 dBm) transmitter power. The equipment is designed to work satisfactorily with temperature variation from 0°C to 55°C with relative humidity of 95% at 35°C. Suitable test points are provided in the back of the equipment to monitor the necessary parameters.
-
product
Temperature and Humidity Transmitter
DST1000
Design for airflow velocity and heat transfer rate Applied to HVAC and clean room High-accuracy,wide-measuring range Wide view angle LCD for sharp display Analog or digital output with current ,voltage and RS485 On line calibration-availability
-
product
Universal Transmitter
Model LXT-330
Teledyne Analytical Instruments
Model LXT330 Liquid Transmitter is a single or dual channel, universal, multi-parameter transmitter, designed for continuous online liquid measurements. It is paired with SP3 Smart sensors and is intended for use in non-hazardous, general purpose rated industrial environments. The SP3 sensor platform covers a wide range of liquid analytical measurements, such as pH, ORP, Specific Ion (pION), dissolved oxygen, free chlorine, total chlorine, conductivity, resistivity and turbidity. The LXT330 transmitter can be used with any SP3 smart sensors without additional user reconfiguration. The Universal Transmitter & Smart Sensor loop philosophy removed the need to stock for multiple instrument types. The process parameter, sensor details, serial number and calibration history are stored in the sensor's main memory, facilitated by two-way digital communication between the sensors and transmitter. The LXT330 universal transmitter allows for up to two SP3 sensors per transmitter (contact factory for available combinations).
-
product
Current / Voltage input Panel meter with output options
DM3420
The DM3420 panel meter accepts Voltage and Current process signals and displays the process value on a high efficiency daylight readable LED display. A built in transmitter power supply is also provided.
-
product
Industrial Temperature Sensors
AMETEK Sensors, Test & Calibration
Temperature measurement and calibration is our specialty, allowing us to provide much more than just standard sensors and assemblies. Our long experience, developing and producing industrial temperature sensors, provides us with a wide knowledge about applications and customer needs. This enables us to build and deliver quick and custom-designed quality temperature sensors for almost any kind of solutions and applications, no matter what industry. We offer a complete range of thermocouple assemblies and resistance thermometers, as well as thermocouple wire, extension wire, temperature transmitters and accessories.
-
product
Pressure Transmitter
PU/PD
- Measurement of gauge pressure with high accuracy 0.25%- Modularity of electrical and hydraulic connections with stainless sealed- Highly resistant to process conditions- Low cost & high stability
-
product
Temperature and Humidity Transmitter
T3419-2
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
Temperature, Humidity, CO2 Transmitter
H6320
The regulators are designed for online measurement of temperature (C or F), relative humidity and carbon dioxide concentration of air without aggressive ingredients. Measured temperature andrelative humidity are recomputed to following humidity expression: dew point temperature, absolutehumidity, specific humidity, mixing ratio and specific enthalpy.
-
product
Water Conductivity Transmitters
ABB conductivity analyzers are designed to meet the most exacting requirements of our valued customers. The extensive range covers 2 and 4-wire analyzers and single or dual-input devices.
-
product
CrystalCalHP Calibration System
AMETEK Sensors, Test & Calibration
This portable gauge and transmitter calibration system is 7 to 10 times faster than a deadweight tester. It allows you to do a 10 point up and down calibration in less than 3 minutes including printing out a calibration certificate.
-
product
Intelligent Transmitter with Digital Indication
LEO 3
KELLER AG für Druckmesstechnik
LEO 3 is a micro-processor based transmitter with digital double-display for pressure (top display) and for the output signal (bottom display). The display is powered from the 4...20 mA current loop. Functions:
-
product
Thin Film Metrology Systems
Gemini Series
The n&k Gemini-TF, Gemini-TF-M and Gemini-FPD are specifically designed for measurements of patterned and unpatterned films on transparent or opaque substrates. These tools are used extensively for solar cell, flat panel and photomask applications. The tools belonging to the Gemini-TF Series are based on unpolarized Reflectance (R) and unpolarized Transmittance (T) measurements, with a 50μm spot size for both R and T. R and T are simultaneously measured to determine film thickness and n and k spectra from 190nm – 1000nm
-
product
Temperature Transmitter Outdoor, Indoor
T0110
Temperature transmitter with 4-20mA output for two-wire connection is built in a durable watertight case. Output temperature range is user adjustable. Degrees Celsius and Fahrenheit are user selectable. Large dual line LCD is an advantage. Display is possible to switch off.
-
product
Voltage Rectifier
A voltage rectifier, designed and manufactured by Monex GeoScope Pty. Ltd., has been added to the terraTEM suite of products. The voltage rectifier has been designed to provide 6 kW, 120 V, 50 A output and is the ideal rectifier to guarantee the necessary stable, ripple free current for the full range of Monex GeoScope’s transmitters. This includes the internal transmitters for the terraTEM24 (50 A, 120V), terraTEM (15 A, 24 V) and the terraTX-50 external transmitter (50 A, 250 V). In addition, the voltage rectifier outputs a clean, filtered 24 V suitable for powering either the terraTEM24 console or terraTX-50 console electronics. And the output stability of the voltage rectifier is not disturbed by the fast turn-off times available on the Monex GeoScope transmitters.
-
product
Hazardous Location Transmitter
X80 Series
The ECD Hazardous Location Transmitters – Model X80 Series provides the same capabilities and general feature set as the general purpose T80 Universal Transmitter. Various configurations are available as single or dual channel for the continuous measurement of pH, ORP, pION, Dissolved Oxygen, Turbidity, Conductivity or Resistivity. The Model X80 transmitter digitally communicates with any ECD Model S88 and/or S80 Intelligent Sensor, automatically configuring the transmitter’s menus and display screens to the measured parameter. The X80 is designed with a durable stainless steel enclosure for explosion proof/exd hazardous applications.
-
product
Digihelic Differential Pressure Controller
DH
The Series DH Digihelic Differential Pressure Controller is a 3 in 1 instrument possessing a digital display gage, control relay switches, and a transmitter with current output. Combining these 3 features allows the reduction of several instruments with one product, saving inventory, installation time and money.
-
product
EMCTD Broadband RF Safety Systems
The EMCTD analog Smart Fieldmeter® is easy to read and to operate. The EMCTD broadband electromagnetic probe covers the 0.2 to 3000 MHz spectrum where most common industrial, communications, medical and government RF emitters are found. The ANGPE-3000 system enables checking of home, office, and workplace RF levels. The system is designed to conveniently measure RF levels around WiFi access points, RFID systems and rooftop antennas; to find transmitter cabinet radiation, locate transmission line leaks, to identify non-radiating antenna elements, and much more. With the supplied NIST-traceable calibration, this system supports laboratory testing of RF devices in compliance with present EMC and RF safety standards.
-
product
Universal Differential pH Water Quality Sensors
SD7500CD
Continuous online pH monitoring in wastewater and coating industrial applications leads to contamination and eventually requires sensors to be replaced. A differential pH sensor utilizes a measurement technique designed to extend the working lifetime of sensors in challenging applications. Replacing the sensor reference (salt bridge) and buffered electrolyte solution can prevent sensor replacements, saving time and money. Our SD7500 Series features a combination sensor output; these differential pH sensors can be used with any conventional pH/ORP transmitter.
-
product
Wireless Meters
Digital Multimeter is loaded with the parameters and ranges HVACR professionals need for HVACR troubleshooting, plus it receives measurements wirelessly from any of the Fieldpiece Accessory Heads when connected to the wireless transmitter that''s included. You can now easily measure current, resistance, voltage, capacitance, frequency, continuity, and temperature either directly, or wirelessly from up to 75'' away.
-
product
Resistance Transmitter
Knick Elektronische Messgeräte GmbH & Co. KG.
Transmitters for resistors and potentiometers in 6 mm housing with calibrated range selection. Functional safety up to SIL 2, SIL 3 redundant to parameterization via interface or intuitively, directly on the device. Universal use with 24 V DC or AC power supply.
-
product
Magnetostrictive Level Transmitter
DM330
The Drexelbrook DM330 magnetostrictive level transmitter is a two wire loop powered intrinsically safe sensor with a configurable 4 -20 mA span.This level transmitter uses proven machine tool positioning accuracy combined with a process compatible float to offer a liquid level, and interface measurement system for the process industry.It comes in a patented low clearance design with all of the sensor’s electronics integrated in a 5/8” diameter sensing tube eliminating the electronics enclosure at the top of the sensor. Not only does this result in reduced cost it also offers its user greater options for insertion and mounting.The DM330 is available in two models.The rigid 316SS model offers a choice of a mini-connector or an optional housing including terminal connectors with zero and span adjustments.
-
product
Single Channel Transmitter
1066
The model 1066 Single Channel Transmitter is a loop powered device that can accept input from pH/ORP, conductivity (contacting and toroidal), and amperometric (dissolved oxygen, chlorine, and ozone) sensors.The model 1066 Single Channel Transmitter can display a liquid analytical measurement, in addition to a temperature measurement, current output, and diagnostic information. The transmitter has quick start programming for shorter installation times and an intuitive user interface for easy operation.
-
product
Event Counter
MS 2022
Event counter is sleek system used to keep track of events. Event counter system is an independent unit with LED, event and reset buttons used for user interface. User generated events are displayed by LED (seven segment display scheme). Event counter Board consists of Microcontroller, counters, monostable multivibrator, transmitters & receivers (RX232, RX422). Event button is used to increment the events and reset button is used to reset the count value. Events are displayed on seven segment display mechanism for visual analysis. Event counter unit starts count from 000 and counts upto 999 events on pressing the event push button. The event value is transmitted over the RS232 / RS422 /TTL communication line to the recorder system.
-
product
Wire Sorter
Shanghai Beha Electronics Co., Ltd.
*Standard signal transmitter identifies up to 12 lines*Clear indication of short circuits, open circuits, or interruptions*Integrated continuity tester
-
product
Transmitters for Humidity Measurement
Our humidity and temperature measurement transmitters with either an interchangeable probe input, or a fixed / integrated probe provide high precision measurements with analogue or digital outputs for process monitoring and control.
-
product
Differential Pressure Transmitters
The differential pressure transmitter portfolio from ABB offers a broad variety of communication possibilities. Another highlight of our sensors is the measurement accuracy up to 0.025 %.
-
product
Temperature, Humidity, Bar. Pressure Transmitter
T7311-2
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Built-in pressure sensor.





























