Module Carriers
Carrier Modules are highly-integrated small footprint board-to-board connectible packages.
-
-
Product
Carrier with System Management
EnsembleSeries™ CCM3011
-
*OpenVPX carrier module designed to use the Data Plane*PCI/PCI-X interface at up tof 133 MHz on each site*x8, x4 and x1 PCIe interfaces*Advanced OpenVPX system management functionality enables remote monitoring, alarm management, and hardware revision and health management*Conduction-cooled and air-cooled variants available
-
Product
Quad M Module Carrier
DP-cPCI-5112
-
DP-cPCI-5112 provides a compact high performance cPCI bus gateway to four ANSI approved M-Module Interfaces. This is a non-intelligent 6U form factor M-Module Carrier board. The DP-cPCI-5112 allows a flexible I/O solutions to be implemented in the carrier board. The M-Module carrier board occupies single slot in a CompactPCI system. Different mix and match of various I/O solutions will simplify the job for system integrators.
-
Product
OpenVPX PMC/XMC carrier.
EnsembleSeries™ CCM6020
-
*First OpenVPX carrier module designed specifically to use the Expansion Plane*PCI/PCI-X interface at up tof 133 MHz on each site*x8, x4 and x1 PCIe interfaces*Advanced OpenVPX system management functionality enables remote monitoring, alarm management, and hardware revision and health management*Conduction-cooled and air-cooled variants available
-
Product
PCIe Gen 3 ATCA Carrier Low-Power Xeon E3
ATC122
-
The ATC122 is a Carrier Module with an on board x16 PCIe Gen3 slot to accept any standard PCIe edge type module. The module has dual 10GbE connected to the Fabric channels and dual GbE to the base channels. It comes with 32 GB of ECC memory. It also has an option for Trusted Platform Management (TPM).
-
Product
Mezzanine Carrier
HMNS AXIe-0
-
The HMNS AXIe-0 module is a carrier of mezzanine modules made in the AXIe-0 standard. The module ensures the functioning of various modules installed in it, made in the form of mezzanines. The HMNS AXIe-0 module is intended for use as a carrier of mezzanines in multichannel systems for collecting/issuing information of both digital and analog types.
-
Product
Frequency Converter up UHF AXIe-0 Up
AXIe-0 Up UHF Module
-
The AXIe-0 Up LMHF module is a carrier of mezzanine modules made in the AXIe-0 standard. The module ensures the functioning of various modules installed in it, made in the form of double mezzanines. The number of slots in the module is one.
-
Product
Others – Carrier Modules
-
To complement the wide range of interface modules for dedicated Avionics Databuses and Networks, AIM offers a range of Carrier modules for the use of AIM or any 3rd Party PMC and XMC module on various backplanes.
-
Product
PXI-2800, 4-Slot PXI Carrier Module for SwitchBlock
781420-00
Switch Block
4-Slot PXI Carrier Module for SwitchBlock - The PXI‑2800 is a carrier module for SwitchBlock that can hold up to six SwitchBlock relay cards while occupying four PXI slots. By connecting multiple SwitchBlock relay cards through the carrier’s integrated analog bus, you can easily create large matrices with more than 2,000 crosspoints in four PXI slots and more than 8,000 crosspoints in a single PXI chassis.
-
Product
3U CompactPCI® Serial XMC Module Carrier Blade
cPCI-A3XMC
Carrier Board
- 3U 4HP CPCI-S.0 peripheral- One XMC slot- Operating temperature: -40°C to 85°C with qualified components
-
Product
30" Ribbon Cable
CONM50-D37-30
-
A 30" ribbon cable transitions from individual IP modules on various carrier boards to a 37 pin D-sub female connector mounted on a PC expansion card end-panel. This allows external connection to pins 1-37 on an individual IP Module.
-
Product
3U VPX Flash Storage Module Carrier
FSM-C
-
Curtiss-Wright Defense Solutions
The Flash Storage Module Carrier (FSM-C) provides rugged, removable, VITA 48.2 compliant, solid state storage in a 1” pitch, industry standard 3U VPX format. By providing a COTS storage solution, the FSM-C can lower schedule and technical risk for embedded storage applications.
-
Product
PCIe Adapter for 3 IP Modules
PCIe3IP
-
IndustryPack® Modules are an important part of solutions for Embedded situations. Rugged, small, light ... just right for many applications. IndustryPack® Modules require a carrier to adapt them to the system. Dynamic Engineering has carrier solutions for a variety of formats. PCIe3IP is designed to support PC computer based solutions. Solutions available for PCI, PC104p, cPCI, VPX and planned for cPCIexpress, PC104e.
-
Product
Selective RF Detector
Raksa iDet
-
RAKSA iDet detects: cellular phones of GSM900/1800, UMTS(3G), CDMA450 standards; cordless DECT phones; Bluetooth and Wi-Fi devices; wireless video cameras; radio transmitters with analog modulation (AM, FM, PM); radio transmitters with digital modulation and continuous carrier (FSK, PSK, etc.); radio transmitters with wideband modulation up to 10 MHz bandwidth.
-
Product
Interface
RCNIC-A2PA3
Interface
The RCNIC platform is a high performance, 3U CompactPCI module (PMC on carrier card) for the AFDX/ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation. An IRIG-B receiver/generator is included for synchronization to an external IRIG-B time source and for synchronization between multiple RCNIC boards.
-
Product
PXIe Module Carrier
HMPXI AXIe-1
-
The PXIe module carrier, HMPXI AXIe-1 Gen3 x4, is specifically designed to support PXIe modules in AXIe systems, allowing you to maximize the best of both standards in a single system. The HMPXI AXIe-1 carrier is designed as a single-slot AXIe-1 module and allows you to simultaneously install two single-slot PXIe modules.
-
Product
PCIe Gen 3 ATCA Carrier With Low-Power Xeon E3
ATC123
-
The ATC123 is a Carrier Module with an onboard x16 PCIe Gen3 slot (only x8 PCIe is routed to the slot) to accept any standard PCIe edge type module.
-
Product
Compact PCI Express (3U) Generic Carrier Card
ACCx-1
-
To complement the wide range of interface modules for dedicated Avionics Databuses and Networks, AIM offers a range of Carrier modules for the use of AIM or any 3rd Party PMC and XMC module on various backplanes.
-
Product
Matrix Module For SwitchBlock
Matrix Switch Module
The Matrix Module for SwitchBlock is for use with the PXI Carrier Module for SwitchBlock and can operate as an individual relay card, can combine with other Matrix Modules for SwitchBlock in the same PXI Carrier Module for SwitchBlock, and can combine with other Matrix Modules for SwitchBlock in other PXI Carrier Modules for SwitchBlock in the same PXI chassis. Each Matrix Module for SwitchBlock comes in an A-type version, which serves as the first matrix building block and offers row and column access through the front connector, and a B-type version, which serves as an expansion module and only provides column access through the front connector. Typically, SwitchBlock systems contain one A-type module and numerous B-type modules.
-
Product
PMC Interface Module Carrier
PIM-Carrier-6U
-
The PMC Carrier routes the PMC IO from P04/P14 to J3/J5. PIM-Carrier-6U routes the IO from J3/J5 to the two PIM positions. The PIMs route the IO to the bezel providing the equivalent of PMC front bezel IO on the rear of the chassis.
-
Product
Universal Military Craft Systems Controller
3U VPX
-
The system is 3U VPX based. It consists of two CPU modules, a power supply module [SMART.PSU] Technology explained <- Click here, two PMC/XMC carrier modules and two MILBUS modules. Optional: WLAN module for controlling the system externally without hanger access (Aircraft on runway - pre-takeoff)
-
Product
SoM Modules
-
Sundance Multiprocessor Technology Ltd.
A System on Module is a small plug on device that has a collection of integrated electronics, like a CPU and/or FPGA and is self-contained and only requires a power source to work. A SoM is typically integrated onto a carrier module with ‘Custom’ I/O to enable interface to Real-World signals.
-
Product
PXI Carrier Module For SwitchBlock
Module
The PXI Carrier Module for SwitchBlock can hold up to six Matrix Modules for SwitchBlock while occupying four PXI slots. By connecting multiple SwitchBlock relay cards through the carrier's integrated analog bus, you can easily create large matrices with more than 2,000 crosspoints in four PXI slots and more than 8,000 crosspoints in a single PXI chassis. Each Matrix Module for SwitchBlock comes in an A-type version, which serves as the first matrix building block and offers row and column access through the front connector, and a B-type version, which serves as an expansion module and only provides column access through the front connector. Typically, SwitchBlock systems contain one A-type module and numerous B-type modules.
-
Product
QuartzXM Carrier Design Package
Model 4801
-
- Pin definitions and electrical specifications of all signals on the module- 3D models of the module- Thermal profiles of the module and components- Carrier reference design schematics- PCB stack-up recommendations- PCB design guidelines and routing rules- Operating systems and bootstrap guidelines- Additional electrical and mechanical engineering guidance
-
Product
15" Ribbon Cable
CONM50-D37
-
A 15" ribbon cable transitions from individual IP modules on various carrier boards to a 37 pin D-sub female connector mounted on a PC expansion card end-panel. This allows external connection to pins 1-37 on an individual IP Module.
-
Product
Processors
-
VadaTech offers ATCA processor blades featuring dual 10-core Intel® Xeon® processors in both 40G and 10G Ethernet variants for maximum performance in a single slot. Our carrier modules offer more versatility, combining a single Intel Xeon processor with a PCIe Gen3 slot so you can add storage, co-processing or acceleration devices to your ATCA system. We also have a range of compatible Rear Transition Modules (RTMs) to expand your IO options.
-
Product
Interface
RCNIC-A2PAX
Interface
The RCNIC platform is a high performance, PCI module (PMC on carrier card) for the AFDX / ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation.
-
Product
Resistance Meter
MT16-4L
-
М-module МТ16-4Л is a mezzanine module (hereinafter referred to as a mezzanine), designed to measure the resistance of resistive sensors using a four-wire measurement circuit in sixteen channels (sixteen-channel digitizer). М-module МТ16-4Л is installed on the mezzanine carrier - module НМ-М and is connected to it via a local information highway. Up to four mezzanines of various types can be installed on the NM-M module. The NM-M module, together with the mezzanines installed on it, forms a VXI module of the C-1 size and is used to create information measuring VXI systems.
-
Product
AMR Module Warm-up Station
3206G
-
The Model 3206G Meter Warm-Up Station for AMR Modules has been specifically designed for meters that utilize the DCSI TWACS™ power line carrier communications module. Additionally, this versatile unit includes voltage output and voltage input connections that allow you to test additional brands of power line carrier modules when using the manufacturer’s supplied module. The Model 3206G can even be used as a simple meter warm-up station.
-
Product
M/MA Module Carrier
VX405C
Carrier Board
The VX405C carrier provides the mechanical and electrical interfaces between the VXIbus and up to six (6) VITA 12-1996 standard M/MA-Modules. The carrier provides VXI register configuration and access to the M/MA-Module I/O space and memory (if present). Each M/MA-Module is controlled separately and appears as a different logical address in the VXI environment. Over 100 M/MA-Modules are available that can provide custom interfacing to the unit under test (UUT). Up to six (6) unique interfaces may be provided in a single VXI slot.
