Thermal Test
Designed to produce a temperature change in a device. The magnitude and rate of this change should induce a sufficient thermal stress fatigue to identify sources of potential failure without causing catastrophic failure of all components. (sigmasystems.com)
See Also: Thermal, Thermal Shock
- Pickering Interfaces Inc.
product
EBIRST 104-pin D-type Test Tool
93-022-001
The 93-022-001 eBIRST 104-pin D-type test tool is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
MCB Thermal Trip Calibration Test Bench (IEC 60898 Cl 9.10.1.2, Annex I.1, IS)
The test system is designed and customized to carry out 2.55*Intest as per Table 7 (test c) of IEC 60898 (also mentioned for routine testing of MCBs. The test is done at dc current to exactly analyze and correct the bimetallic properties of the MCB as far as thermal tripping is concerned. The unit comes with a pneumatically operated test fixture with in-built dc stepper motor that is controlled by a micro controller / PC to calibrate the breaker into a narrow tripping band programmed by the user.
-
product
New Car Battery Tester
Hangzhou Xun Anda Electrical Co., Ltd.
1. Test application: 12V/6V batteries test and 12V Starting /Charging system test.2. Test battery type: regular liquid, AGM battery, GEL battery.3. CCA test range: 40~2000CCA (SAE).4. Voltage test range: 1.5-15V.5. Display SOH (state of health), SOC(state of charge).6. Test for multiple battery standards: SAE, DIN, EN, IEC, CA.7. Graphic LCD display with back light, LCD brightness adjustable.8. Multigle language operation: English, Chinese, Germany, French, Spanish.9. Intergrated thermal printer to print test reports.10. Thermal printer paper roll is 58mm width and 7.5m long.
-
product
Franklin Tester
Model FT1
The Franklin tester FT‐1 is designed to measure the surface insulation resistivity of electrical steel sheet according to the ASTM Standard A717 and IS:649. This test method is suitable for quality control in the application of insulation coating. For ease of testing FT‐1 automatically set 300 PSI pressure on the sample by the inbuilt hydraulic unit and it is capable to set the desired test temperature of the platform. Then the regulated supply of 0.5V gets on and the current flowing through the insulation get measured. The calculated insulation resistivity will be displayed on graphics LCD display and as well as on printed report via thermal printer.
-
product
Rubber Testing Equipment
Dongguan Amade Instruments Technology Co., Ltd
Rubber testing equipment are used to test the physical properties, chemical properties, thermal properties of uncompounded and compounded rubbers at prescribed conditions to help manufactures or researchers in comprehending the characteristics, updating the formula and improving product quality. Including volatile component, ash content, Mooney viscosity, vulcanization curve, Mooney scorch time, hardness, tensile properties, tearing, the compression performance, impact, friction resistance, fati...show more -
product
High Temperature Hot Mountable Furnace Extensometers (1200 Cor 1600 C)
Model 3549
Jinan Testing Equipment IE Corporation
The Model 3549 is a major advancement in the design of externally mounted, furnace extensometers. This new extensometer is designed to meet the stringent requirements of strain controlled testing as prescribed in ISO 6892, while introducing many new innovative features that help improve productivity with static testing applications (tension and compression testing) and long term testing such as low cycle fatigue and creep. The overall design reduces any influence from common lab environment vibr...show more -
product
Thermal Shroud
BC8-55/150C
When combined with a thermal conditioner such as the Bemco PCL3L-III or PCL3M-III, this shroud converts a 24 inch inside diameter by 30 inch high vacuum only vertical bell jar into a 19 inch inside diameter by 20 inch high thermal vacuum testing system. With a convenient clam shell door, test objects are easily loaded by simply raising the bell jar above the top of the door opening.
-
product
Double-deck High and Low Temperature Environmental Test Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Double-deck High and Low Temperature chamber was designed to test battery cell combined with charge and discharge equipment, and also available to thermal test for small products and components.
-
product
Thermal Test Vehicles
TTV
Thermal Engineering Associates, Inc.
Using the TTC-1002 Thermal Test Chip as a basis, TEA offers TTVs in flip-chip, bare die, BGA packages for a variety of thermal simulation, reliability, qualification, heat sink characterization, and TIM characterization activities. Selective unused balls are sequentially connected together for daisy-chain applications.
-
product
Instruments
Advanced Thermal Solutions, Inc.
ATS designs and fabricates the most extensive line of thermal test instruments specifically designed for the electronics industry. These research-quality, state-of-the-art instruments include Pressure, Temperature and Velocity Measurement Systems, Airflow and Heat Flux Controllers, Micron-level Thermography Systems and Cold-Plate Thermal Characterization Systems.
-
product
System and Collection Tester
SysColl
For certification in many markets, performance of the complete factory made system (for example thermosiphon systems) plays an equally important role as collector performance. Our SysColl test stand is a combined test facility for performance testing of both solar collectors and solar thermal systems. This allows you to take advantage of a flexible two in one test solution.
-
product
PXI-2564 , 16-Channel, 5 A, SPST PXI Relay Module
PXI-2564 / 778572-64
16-Channel, 5 A, SPST PXI Relay Module—The PXI‑2564 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2564 is fully software programmable. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for switching medium‑ to high‑power signals and loads in military, automotive, or automated test applications.
-
product
Lighting Reliability
LED/OLED package lifetime is highly dependent on thermal management, and LED lamp performance can be dependent on the luminaire in which it is installed. Lighting reliability test system for LED/OLED Products are widely used for normal /accelerated aging, lumen maintenance measuring, lifetime evaluation and temperature characteristic testing for LED/OLED products including LED package, array, module, OLED module and luminaires.
-
product
Milliohm Meter
16502
Chroma Systems Solutions, Inc.
Basic accuracy : 0.05%Pulsed test current output mode is used to reduce thermal EMFs affection on milliohm measurementDC test current output mode is used to fasten measurement speed for inductive DUTDry-circuit test current output mode (limited Max. 20mV) is used to measure such contact resistances where the maximum open-circuit voltage must be limited to 50mVTemperature correction (TC function) regardless of material or temperatureUseful temperature conversion function for motor/ coil evaluatio...show more -
product
Vibration Table Top system
OVTT 18
The OVTT, Omni-Axial Vibration Table Top system, is the first, stand-alone, compact, repetitive-shock vibration system on the market. The OVTT 18 system is ideal for No Fault Found (NFF) precipitation screens of field returns, repair verification and random vibration test of small products. The OVTT 18 utilizes Qualmark's patented six-degree-of-freedom vibration technology and is designed with reduced air requirements and low noice levels. The OVTT 18 system can be easily configured for placement inside a thermal chamber for combined stress tests.
-
product
Climatic Testing
Environmental Test Chamber. Environment Associates' complete Climatic test facilities offer precise simulation of Temperature, Humidity, Altitude, Thermal Vacuum, Salt Fog, Sand and Dust, and Rain as well as many other specialized environments. Microprocessor Control along with calibrated recorded measurements and outstanding attention to detail by our technical staff make for a perfect test everytime.
-
product
PXI-2520, 80-Channel, 2 A, SPST PXI Relay Module
778572-20
80-Channel, 2 A, SPST PXI Relay Module—The PXI‑2520 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2520 is fully software programmable, and it supports onboard relay count tracking. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for automated test equipment (ATE) loads or for controlling heaters, lights, and fans.
-
product
Pick and Place Test Handler
Delta MATRiX
Cohu’s MATRiX handler has a highly flexible test site configuration that’s well suited for a wide range of test applications, including analog ICs with short test times and high throughput, automotive devices requiring accurate thermal control, small pitch wireless-communication products, high parallel microcontroller testing, MEMS device testing, and many other device market segments with their unique requirements. The MATRiX has a highly flexible test site configuration that enables customers to reuse existing load-boards, including boards made for competitor’s legacy handlers.
-
product
Test House Services
At TS-Space Systems we have over 30 years experience in designing, building and operating vacuum systems for space simulation and materials testing. We have three in-house thermal vacuum chambers which are configurable for a range of temperatures for either monitored vacuum bakeout or thermal vacuum cycling. We design, build and operate these systems in-house which means we are more flexible than most test houses and are happy to modify feedthroughs, manufacture additional support equipment and even change the operation of the chambers, where possible, in order to accomodate customer requirements.
-
product
Climatic Chamber
Wewon Environmental Chambers Co, Ltd.
Climatic chamber is designed to do high temperature & high humidity, high and low temperature, or temperature cycling test, Climatic chamber mainly used for quality checking and assessing their quality reliability and life test. ● The climatic chamber simulate a full range of temperature testing and humidity testing conditions.These chambers are designed for ease-of-use, reliability and performance and include many user-friendly features standard with your purchase for the best value in the ...show more -
product
Thermal Cycling and Humidity-Freeze Test
King Design Industrial Co., Ltd.
*10.4" TFT LCD, touch-type Chinese/English display controller.*Temperature/humidity setting procedure, LCD curve display device (set to “curve display”).*Chinese/English/LCD operation/troubleshoot/guiding window.*State-of-the-art intelligent auto-dispatch “heat load value” coolant servo valve flowrate algorithm control.
-
product
PXIe-2529, 128-Crosspoint, 4x32 OR 8x16, 2-Wire PXI Matrix Switch Module
780587-29
128-Crosspoint, 2-Wire PXI Matrix Switch Module—The PXIe‑2529 is a high‐density PXI matrix switch module that you can configure as either a 4x32 or an 8x16 2‑wire matrix by using different terminal block accessories. It uses electromechanical relays that offer excellent performance for high-power signals and low thermal offset for accurate measurements at low-voltage levels. The PXIe‑2529 also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
Sensors Test Cells
Integrated MEMS
The best technical performance, cost optimization, one-shot factory integration.A single unit integrates the modules for the handling, contacting and complete testing of MEMS devices, including the physical stimulus for functional test, and the tri-temp thermal conditioning.
-
product
Test Equipment
Test Devices has developed the world’s most precise, accurate and efficient test solutions because the company employs very experienced and accomplished scientists and engineers. For almost 40 years Test Devices has developed and advanced the science of centrifugal, vibratory and thermal stress testing and measurement of rotational components – critical solutions engineers need to evaluate integrity and validate component parts.
-
product
New Lead Acid Battery CCA Tester With Printer
Hangzhou Xun Anda Electrical Co., Ltd.
1. Test application: 12V/6V batteries test and 12V/24v Starting /Charging system test.2. Test battery type: regular liquid, AGM battery, GEL battery.3. CCA test range: 40~2000CCA (SAE).4. Voltage test range: 1.5-30V.5. Display SOH (state of health), SOC(state of charge).6. Test for multiple battery standards: SAE, DIN, EN, IEC, CA.JIS7. Graphic LCD display with back light, LCD brightness adjustable.8. Multigle language operation: English, Chinese, Germany, French, Spanish.9. Intergrated thermal printer to print test reports.10. Thermal printer paper roll is 58mm width and 7.5m long.
-
product
Thermal Conductivity Measuring Device
TCM1001
In recent years, there has been a demand for small and thin electronic products such as mobile devices, and printed circuit boards are shifting to thin, multi-layered, and even modularized printed circuit boards. effect of bonding materials, that is, the ability to easily conduct heat, is emphasized, and testing equipment that evaluates thermal conductivity is required .As a business of our company, we have mainly manufactured and sold test equipment for solder wettability tests and solder bondi...show more -
product
Tracker
For regions with stable weather conditions, PSE provides two outdoor bi-axial trackers, which keep test samples perpendicular to the sun. PSE trackers are designed for outdoor testing and certification of both solar thermal collectors and PV modules. With our trackers it is possible to test more than one collector at the same time. Simultaneous collector testing can allow direct comparison of different collector designs under identical conditions or increase the measurement throughput of collectors and modules. In our product line we offer the following tracking systems:
-
product
Current Transformer Testers
Vanguard Instruments Company, Inc.
Performs CT excitation, current-ratio, polarity, and phase angle testsMeasures insulation resistance and winding resistance of the CT seconday windingsMeasures the CT's secondary burdenTest record header information including company, substation name, circuit ID, manufacturer, CT serial number, operator name, and test record-commentsBuilt-in 4.5-inch wide thermal printerPlot Multiple Saturation CurvesStores up to 128 CT test plans and 140 test records internallyUSB, Bluetooth, and USB Flash drive interface
-
product
Shoe Cold Insulation Tester
UI-FT09
Shoe Cold Insulation Tester is used to test shoe cold insulation ability / thermal insulation against cold performance..
-
product
Process Thermal Conductivity Analyzer
CI-IN56
Shanghai ChangAi Electronic Science & Technology Co.,Ltd
CI-IN56 thermal conductivity analyzer is a kind of intelligent analyzer based on microprocessor, considering microprocessor thermal conductivity sensor as measuring unit. It has high accuracy, good stability, comprehensive function and long service life. Applied to test the H2 or He in binary gas or binary mixture gas. - See more at: http://en.ci-ele.com/dcb675d2-4e33-4eb9-33a0-60edf78c9348/6b085f77-cb25-8ccc-faaf-9b581710d730.shtml#sthash.Xs2anvsw.dpuf
-
product
Measurement System For Testing & Binning Of Back-End LEDs
TP121-TH
The photometric specifications of LEDs must meet very high tolerance requirements regardless of whether they are to be used in general, automotive or other specialist lighting applications. This is often a problem since the manufacturing tolerances of LEDs can be higher than those permitted in the end-use applications. Also, LED binning by LED manufacturers in order to classify LEDs based on their tolerances is performed with flash mode testing using pulsed current flow. However, end-use applica...show more