Thermal Test
Designed to produce a temperature change in a device. The magnitude and rate of this change should induce a sufficient thermal stress fatigue to identify sources of potential failure without causing catastrophic failure of all components. (sigmasystems.com)
See Also: Thermal, Thermal Shock
-
Product
Semiconductor
-
With ultra-multi pin count and fine pitch, our general-purpose IC socket lineup corresponds to every need. For semiconductor burn-in sockets for thermal acceleration tests, and test sockets for semiconductor electrical testing, we continue to hold a high market share all over the world.
-
Product
Thermal Vacuum Data Acquisition and Control Software
TVAC 7000
Data Acquisition Module
Equipment used in space applications needs to go through stringent environmental tests in order to prove that it can survive the extreme conditions experienced during launch and while in space. Some of the key environmental tests include vibration, thermal vacuum, and electromagnetic compatibility. Thermal vacuum test is crucial to confirm the equipment is able to operate under the space vacuum condition.
-
Product
Thermal Shock Test Chamber
-
observe the product characteristics and failure occurrences caused by different materials and their thermal expansion coefficients, thermal shock testing is subjected to the product. In thermal shock testing alternating high and low temperatures are fed in the chamber. WEIBER designs and manufactures customised THERMAL SHOCK CHAMBERS with separately controlled temperature zones (2 zone and 3 zone), liquid to liquid (2 zone) depending on configuration of the chamber chosen.
-
Product
Liquid-To-Liquid Thermal Shock Chambers
-
Purchasing a liquid thermal shock chamber needs close consideration of the long term operating costs. The specialized liquids used can easily evaporate, causing the loss of thousands of dollars of fluid per year, if not properly contained. Liquid-to-liquid thermal shock testing is typically conducted to apply very strong, repetitive thermal stress to test pieces. It can model a product's ability to withstand thermally-induced size changes, crack resistance, hermetic integrity, and changes in electrical properties. This form of testing provides a very rapid temperature shock recovery of conditions, and it can significantly reduce testing time by requiring shorter soaks and less cycles.
-
Product
Climatic Test Chamber
-
Before anything reaches out for market distribution, you would need to determine its exact quality and performance to that follows to the point with readings. Thermal and environment testing are some of the most positive aspects to get your materials tested for their underlying performance capacity and reliability in quality.
-
Product
Singlebeam Hydrographic Echosounders
-
Teledyne Marine Odom Hydrographic
Odom Hydrographic provides an extensive range of hydrographic level single beam echosounders with the flexibility of frequency agility supporting existing transducer installations. Models include modern PC screen based interfaces as well as support for tried and tested thermal record printing.
-
Product
Thermal Shock Test Chamber (Three Zone)
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Thermal Shock Test Chamber (3 Zone) consist of the Test Zone, Heat Storage Zone and Cold Storage Zone. The specimen stay in test zone, hot and cold air will be blew from the storage zones to achieve rapid temperature change for thermal shock.
-
Product
Customized Thermal Management Test Bench Solutions
-
Our IPEtec test bench engineering business unit plans and provides customized test bench solutions for the development and validation of automotive AC components. We offer a full range of test benches and media-supply modules for the automotive developer’s thermal management needs. Moreover, we support the development of new cooling systems for hybrid power trains, for battery and engine cooling. New hybrid power trains are opening up additional fields of heat-pump technology development aimed at optimizing the energy balance of automotive air conditioning.
-
Product
LifeTest Software
-
In combination with the extended range of PEC test equipment, LifeTest supports the many specific functionalities required in battery testing labs. Drive cycle simulations (FUDS, DST…), thermal performance tests, high speed pulse tests (HPPT), life cycle tests, accelerated ageing tests and internal resistance measurement tests can be easily configured, scheduled, executed and reported from a single platform.
-
Product
Environmental Test Chamber
-
High and Low Temperature Test Chambers, ESS Environment Stress Screening, 2 Zone Thermal Shock Test Chamber, 3 Zone Thermal Shock Chambers, Walk-In Chambers, Burn-in Room and Aging Test Chambers, Altitude Chambers, Industrial Drying Oven, Salt Spray Test Chambers, Temperature Humidity Vibration Comprehensive Test Chamber, Test Machine Series, Custom Made Environmental Test Equipment, Double-Layer High and Low Temperature Chamber, Explosion Proof Temperature Chamber For Power Battery, etc.
-
Product
IR FPA sensors
-
IR FPA sensors are the most important modules of thermal imagers. Design of sensor electronics (camera core) is a crucial part of designing of new thermal imager. Knowledge of precise parameters of IR FPA sensor is needed by both professionals involved in both IR FPA technology/thermal imagers technology because parameters of IR FPA sensors determine performance limits of thermal imagers. Therefore test equipment that enable measurement of IR FPA sensors is a vital tool for development of both IR FPA technology/thermal imagers technology. It is commonly known that data sheets provided by manufacturers of IR FPA sensors (both cooled or non-cooled) provide too little details for electronics designers. Sometimes the provided data is not accurate enough and better sensor performance can be achieved using modified control signals. Therefore design teams loose sometimes years to develop electronic camera core optimized for a specific IR FPA sensor. When the type of the IR FPA sensor is changed the whole process is to be repeated. In this situation an universal, flexible camera core that would accept IR FPA sensors from different manufacturers and to carry out semi-automatic determination of optimal signal controls for a specific IR FPA sensor would be highly desirable.
-
Product
Hybrid Single Site Test Handler
3110
-
Chroma Hybrid Single Site Test Handler 3110 is a full range ATC (Active Thermal Control) test handler capable of handling device bodies up to 120x120mm with 450kg force load.
-
Product
Temperature shock test chambers test
TSS series
-
The operating principle of Schocktestprfschrank based of two superposed test rooms (top hot chamber, cold chamber below), between which a car with the test specimens is moved up and down by the large thermal shock test equipment may be subjected
-
Product
Thermal Shock Test Chamber (3 Zone)
-
Guangdong Test EQ Equipment co., Ltd.
- Divided into a high-temperature zone, low-temperature zone, and test zone. The test product is placed in the test zone, and the temperature from the high-temperature zone or low-temperature zone is applied to the test zone for thermal shock. The test product remains static during the test.- Equiped with a touch-screen control interface for easy operation.- Temperature is transferred to the test zone using a wind route switching method to perform thermal shock testing.- The maximum duration of high-temperature or low-temperature shock can reach 999 hours, and the maximum cycle period can reach 9999 cycles.- The system can operate in automatic cycle mode or manually select specific shocks. It can be set to perform two-zone or three-zone shocks, as well as cold-to-hot or hot-to-cold transitions.- The cooling system utilizes a dual refrigeration system, providing fast cooling. Water cooling is employed as the cooling method.- Testing can be performed at room temperature.
-
Product
Thermal Cycling Test Equipment
-
Wewon Environmental Chambers Co, Ltd.
IC welding to PCB, IC is integrated in the chip general purpose circuit, it is a whole. Once the inside is damaged, the chip will be damaged. The goal of printed circuit boards (pcbs) is to connect IC and discrete components to form a larger working circuit. Thermal cycling equipment can detect the defects and hidden dangers of welding components in the production process, decreasing failure rate. When it fails, components can be replaced in timehttps://www.wewontech.com/thermal-cycling-test-equipment/
-
Product
Thermal Testing And Analysis
-
Response Dynamics Vibration Engineering, Inc.
We have consulted on thermal issues ranging from conduction issues in TECs, thermal radiation modeling, and countless air cooled system issues relating to system performance, vibration, and acoustics noise. We use a wide array of thermocouple instrumentation, thermal imaging, flow measurements, as well as finite element analysis and analytic modeling to measure, design, and debug thermal and related issues. We often work on customer products in our Response Dynamics lab where we characterize the system, engineer solution options, and prototype solutions. We then work with the customer to work the winning solution into their quality control and manufacturing process.
-
Product
Test System for Circuit Breakers
-
Spitzenberger & Spies GmbH & Co. KG
Thermal testing with long-time currents up to 550 A. Magnetic testing with short-time currents up to 2000 A. Control software. Customer specifically adapted. 4 candidate records with pneumatic adapting.
-
Product
Thermal Shock Test Chamber (2 Zone)
-
Guangdong Test EQ Equipment co., Ltd.
- Thermal Shock Chamber: -70℃~150℃, ≤5min recovery, meets MIL-STD-810. Ideal for PCB/IC reliability testing.- ESS Environmental Chamber: Humidity 20%~98% RH, supports GB/T 2423 standards. 40% energy saving vs. competitors.- Liquid-to-Liquid Shock Tester: LN₂ cooling to -196℃, 15s transition time. For aerospace materials validation.- Thermal Cycling Equipment: 25℃/min ramp rate, 1000L capacity. JESD22-A104 compliant.- Benchtop Thermal Chamber: -65℃~150℃, 65dB low noise. Lab-use with USB data export.
-
Product
Environmental Testing
-
Environmental testing typically involves hot or cold temperatures, humidity, altitude (vacuum) or thermal shock. This testing can even be combined with other test methods such as vibration or shock.
-
Product
Semiconductor Package Wind Tunnel
WT-100
-
Thermal Engineering Associates, Inc.
The WT-100 Forced Convection (Moving Air) Wind Tunnel is designed in accordance with the EIA/JEDEC JESD51-6 standard for thermal characterization of semiconductor packages and devices. The vertical design minimizes laboratory floor space requiements. Air is drawn in at the bottom and exhausts at the top. The test section is large enough to accommodate the largest JEDEC and SEMI thermal test boards. Air velocity can be adjusted over the range of 0.5 to 5 m/s; air velocity is monitored with an included hot-wire anemometer connected to a digital display. A Type-T thermocouple is mounted in the test section for monitoring the moving air temperature.
-
Product
MCB Thermal Verification Test Bench
-
The test system is a special version of the thermal test test system in the sense that the test jig is primarily designed to hold and connect multi pole MCBs for thermal verification so that each pole can be verified to trip within the IEC time band after the MCB has been riveted. This test ensures the trip verification of MCB so as to trip all the 4 poles at once when overload is detected in one single pole. In short, this is a verification-only bench.
-
Product
Double-deck High and Low Temperature Environmental Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Double-deck High and Low Temperature chamber was designed to test battery cell combined with charge and discharge equipment, and also available to thermal test for small products and components.
-
Product
Thermal Shock Test Chambers
-
How well does your product stand up to the shock of extreme thermal temperature changes? Tenney Environmental's thermal shock test chambers take products from 200°C to -65°C in just seconds.
-
Product
TIM Characterization Tools
-
Thermal Engineering Associates, Inc.
Combining Thermal Test Vehicles (TTVs) with Thermal Test Boards (TTBs) results in a set of tools that perform the basis for TIM thermal characterization under application-oriented measurement conditions. Availability of these tools creates a de facto standard that enable both TIM manufacturers and TIM users to compare measurement results under the same conditions.
-
Product
Guarded Heat Flow Meter
-
The Guarded Heat Flow Meter (GHFM-02) follows ASTM E1530-19 for testing thermal resistance and thermal conductivity of solids, such as metals, polymers and composites. The easy to operate GHFM-02 follows the trusted steady-state approach, with the addition of a guard to limit the effects of lateral heat loss. This design, allows testing of a wide range of materials with low to medium thermal conductivity.
-
Product
Thermal Abuse Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL Thermal abuse test chamber protect for short circuit caused by incorrect operation of the operator and battery electrode, battery positive and negative connection, etc
-
Product
Pyroelectric and Thermal Testing
-
The optional Chamber Task measures the Pulse Polarization response and Small Signal Capacitance of a Pyroelectric material that is being heated and/or cooled within a thermal chamber, on a hot chuck or in a furnace. From these measurements the Spontaneous Polarization Pr(q) and the Dielectric Constant er(q) are computed. These are then combined to determine the Electrical Displacement D(q) as a function of the temperature q.
-
Product
Targets
-
Targets from group A are developed to support mostly testing infrared imaging systems understood as thermal imagers. These targets can be used also in testing visible/near infrared cameras or SWIR cameras but such application is not optimal. IR targets are mostly used in DT systems for testing thermal imagers and in MS systems for testing multi-spectral systems.
-
Product
Digital Closed Loop Control Thermal and Mechanical Testing System
3800 System
-
The Gleeble 3800 is a fully integrated digital closed loop control thermal and mechanical testing system. Easy-to-use Windows based computer software, combined with an array of powerful processors, provides an extremely user-friendly interface to create, run and analyze data from thermal-mechanical tests and physical simulation programs.The result is a system unequaled for physical simulation and thermal-mechanical materials testing.
-
Product
Temperature/Humidity Vibration Test Systems
EHVC SERIES
-
The EHVC Series is designed for highly accelerated life testing, the demand of which from customers is increasing today. This is a joint system of the AGREE chamber and thermal shock chamber that we have manufactured and makes the temperature rate up to 20℃/min feasible with a compressor only. With this feature, the highly accelerated life test such as AGREE tests, most thermal shock tests can be performed with one unit.
