Thermal Test
Designed to produce a temperature change in a device. The magnitude and rate of this change should induce a sufficient thermal stress fatigue to identify sources of potential failure without causing catastrophic failure of all components. (sigmasystems.com)
See Also: Thermal, Thermal Shock
-
Product
Bypass Diode Thermal Test System
-
King Design Industrial Co., Ltd.
* Power: the heating board control panel uses 220V single-phase power.* Power consumption: 1.0KVA, 1000W(Max)* Volt: 220VAC* Current: 4.5A* Heating board: one controller per board* Power rate: room temperature raise to 75°C± 5°C within one minute.* Heating board dimension: 500mm x 1,000mm* 6-sheet electrical heating boards test: used to test the 2,200mm x 2,600mm module. It can be customer-designed.* The length of board power cable and thermal sensor cable shall exceed 3,000mm.* To get uniform heating effect, the electrical board is sandwiched by 2mm aluminum sheets at both sides of board.
-
Product
Thermal Stability Test System
-
Premier Electrosystems' Thermal Stability Test Setup is used to test thermoplastics and PVC (Plasticized Polyvinyl Chloride) materials. When exposed to continuous heat, these materials degenerate and emit harmful acidic gases. The instrument is manufactured for testing PVC materials for their thermal stability at higher temperature.
-
Product
Thermal Runaway Test Machine
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL Thermal runaway test machine test the whole vehicle or the complete vehicle-borne ion battery system or the subsystem of vehicle-borne lithium-ion battery system, including a lithium ion battery and an electrically connected lithium ion battery. The applicable standard is UL 2580, IEC 62619.
-
Product
MCB Thermal Verification Test Bench
-
The test system is a special version of the thermal test test system in the sense that the test jig is primarily designed to hold and connect multi pole MCBs for thermal verification so that each pole can be verified to trip within the IEC time band after the MCB has been riveted. This test ensures the trip verification of MCB so as to trip all the 4 poles at once when overload is detected in one single pole. In short, this is a verification-only bench.
-
Product
Battery Module Test Equipments
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's battery test equipments series mainly for testing the battery module of Electric-bike, Electric Motorcycles, etc. These series meet the standard compliance of IEC62619, UL2580 and GB31485-2015. Including short circuit, thermal test, drop test and crush test, etc.
-
Product
Temperature Calibration System
-
Thermal Engineering Associates, Inc.
Systems for determining relationship between temperature-sensing junction voltage versus junction temperature of diodes, integrated circuits and thermal test die. Provides internal current sources, voltage measurement to 1 mV, and temperature measurement to 0.1ºC. 16-channel capability with optional printer and serial port data output.
-
Product
Power Supply Rack For Climatic Cycling Test
-
One essential part of the module quality testing according to IEC 61215 is the thermal cycling test (MQT 11) and humidity freeze test (MQT 12). Besides the environment simulation in the climate chamber, it is necessary to energize the PV modules during specific parts of the test.
-
Product
MCB Thermal + Magnetic Characteristic Test Bench
-
The test system is a special version of the thermal + Magnetic test test system. The single power source able to deliver either thermal or magnetic test parameters set on the PC by the user.
-
Product
Mechatronics
-
MERA performs design, construction, supply, installation and certification of stands for various testing types:● static loading● dynamic and life-cycle● transporting testing (vibration table)● thermal testing● centrifuges● modeling of take-off, landing modes, etc.
-
Product
Guarded Heat Flow Meter
-
The Guarded Heat Flow Meter (GHFM-02) follows ASTM E1530-19 for testing thermal resistance and thermal conductivity of solids, such as metals, polymers and composites. The easy to operate GHFM-02 follows the trusted steady-state approach, with the addition of a guard to limit the effects of lateral heat loss. This design, allows testing of a wide range of materials with low to medium thermal conductivity.
-
Product
Targets
-
Targets from group A are developed to support mostly testing infrared imaging systems understood as thermal imagers. These targets can be used also in testing visible/near infrared cameras or SWIR cameras but such application is not optimal. IR targets are mostly used in DT systems for testing thermal imagers and in MS systems for testing multi-spectral systems.
-
Product
Semiconductor
-
With ultra-multi pin count and fine pitch, our general-purpose IC socket lineup corresponds to every need. For semiconductor burn-in sockets for thermal acceleration tests, and test sockets for semiconductor electrical testing, we continue to hold a high market share all over the world.
-
Product
Temperature Humidity Environmental Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Temperature and Humidity Test Chamber is able to simulate a wide range of temperature and humidity environment condition for testing various products and components. It is widely used for basic thermal cycling test and accelerated stress test. We provide 6 standard models, test cabinet from 80L to 1000L, customized size is also available.
-
Product
Thermal Test Vehicles
TTV
-
Thermal Engineering Associates, Inc.
Using the TTC-1002 Thermal Test Chip as a basis, TEA offers TTVs in flip-chip, bare die, BGA packages for a variety of thermal simulation, reliability, qualification, heat sink characterization, and TIM characterization activities. Selective unused balls are sequentially connected together for daisy-chain applications.
-
Product
Thermal Shock Test Chambers
-
How well does your product stand up to the shock of extreme thermal temperature changes? Tenney Environmental's thermal shock test chambers take products from 200°C to -65°C in just seconds.
-
Product
Thermal imagers
-
Thermal imagers sensitive in MWIR and LWIR spectral bands are one of crucial surveillance technologies for defense/security sector. These imagers have also found mass applications outside defense sector. Testing thermal imagers is needed for both manufacturers, maintenance workshops and final users for a set of different and important reasons. Hi-tech test equipment can help significantly in manufacturing, maintenance, training, purchase optimization, and optimal use of these expensive imagers.
-
Product
Temperature/Humidity Vibration Test Systems
EHVC SERIES
-
The EHVC Series is designed for highly accelerated life testing, the demand of which from customers is increasing today. This is a joint system of the AGREE chamber and thermal shock chamber that we have manufactured and makes the temperature rate up to 20℃/min feasible with a compressor only. With this feature, the highly accelerated life test such as AGREE tests, most thermal shock tests can be performed with one unit.
-
Product
Precise Temperature Forcing System
TA-5000A Series
-
The ThermalAir TA-5000 Series of temperature forcing systems bring precise thermal testing capabilities directly to your test application, exactly localizing to where thermal conditioning temperature cycling is required. ThermalAir TA-5000 temperature systems provide flexible thermal test solutions for an array of products and technologies.
-
Product
Thermal Shock Test Chamber
-
observe the product characteristics and failure occurrences caused by different materials and their thermal expansion coefficients, thermal shock testing is subjected to the product. In thermal shock testing alternating high and low temperatures are fed in the chamber. WEIBER designs and manufactures customised THERMAL SHOCK CHAMBERS with separately controlled temperature zones (2 zone and 3 zone), liquid to liquid (2 zone) depending on configuration of the chamber chosen.
-
Product
Thermal Vacuum Data Acquisition and Control Software
TVAC 7000
Data Acquisition Module
Equipment used in space applications needs to go through stringent environmental tests in order to prove that it can survive the extreme conditions experienced during launch and while in space. Some of the key environmental tests include vibration, thermal vacuum, and electromagnetic compatibility. Thermal vacuum test is crucial to confirm the equipment is able to operate under the space vacuum condition.
-
Product
Liquid-To-Liquid Thermal Shock Chambers
-
Purchasing a liquid thermal shock chamber needs close consideration of the long term operating costs. The specialized liquids used can easily evaporate, causing the loss of thousands of dollars of fluid per year, if not properly contained. Liquid-to-liquid thermal shock testing is typically conducted to apply very strong, repetitive thermal stress to test pieces. It can model a product's ability to withstand thermally-induced size changes, crack resistance, hermetic integrity, and changes in electrical properties. This form of testing provides a very rapid temperature shock recovery of conditions, and it can significantly reduce testing time by requiring shorter soaks and less cycles.
-
Product
Thermal Shock Environmental Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Thermal Shock Chamber provide the sudden temperature changes between extreme cold and extreme hot from -65℃ to 150℃ (customized available), specially for environmental stress screen test of the industries that rely on thermal testing, such as component, board electronic assemblies, defense, material stress, consumer products etc. The thermal shock test can cause faulting or cracking by the expansion and contraction on the products, indicates the hidden manufacturing defects. Bell’s Thermal Shock Chamber ensure you to launch qualified product to the market.
-
Product
SPD AC & DC Thermal Stability Test Equipment
-
Shanghai Guantu Technology Co., Ltd.
1. Computer control measurement, PLC control;2. Equipped with sudden voltage capability, suitable for thermal stability tripping test under high current conditions;3. Increase the high-power resistance box;4. The interface is friendly and beautiful, and can reflect the running status of the system in real time; .5. Automatically draw voltage, current and temperature curves;6. The system performs multi-point temperature detection in real time;7. Timing sampling and recording function, which is convenient for users to view temperature values at different times and compare data;8.2 times Uc leakage current test function to check the tripping reliability of the product;9. Built-in test box;10. RS232 communication interface, can realize remote control.
-
Product
Thermal Abuse Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL Thermal abuse test chamber protect for short circuit caused by incorrect operation of the operator and battery electrode, battery positive and negative connection, etc
-
Product
Test Equipment For IEC 62133
-
designed for the battery thermal abuse test for IEC62133-8.2.2. The fire-proof dual-chamber has dimension 10" x 10" x 8", which can be heated up to 180°C via an independent temperature controller with +/- 1°C accuracy.
-
Product
Hybrid Single Site Test Handler
3110
-
Chroma Hybrid Single Site Test Handler 3110 is a full range ATC (Active Thermal Control) test handler capable of handling device bodies up to 120x120mm with 450kg force load.
-
Product
OSFP 800G
-
OSFP800 has emerged as a leading standard to drive the development of 800G ecosystem. The MultiLane OSFP800 development kit is an essential tool to ensure the validity of your OSFP800 products. The module compliance board (MCB) is used to test transceivers, AOCs, active cables and DACs, while the host compliance board (HCB) enables the testing of system host ports. The loopback modules (LB) provide an economical way to test thermal capacity and signal integrity of system host ports at every stage of the process: R&D validation, production testing, and field testing.
-
Product
Thermal Testing
-
A view of multiple testing stations for use in conducting Thermal Analysis on various materials. This is one of several areas assigned to various thermal tests. Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TGA), Thermomechanical Analysis (TMA), and Dynamic Mechanical Analysis (DMA)
-
Product
Battery Test Equipment
-
Shenzhen Bonad Instrument Co., Ltd.
The tests that can be performed by lithium-ion battery safety testing equipment include temperature cycling test, thermal abuse test, high altitude low-pressure simulation test, vibration test, shock test, external short-circuit test, forced internal short-circuit test, drop test, crush test, impact test, nail penetration test, burning test, etc. These test items mainly apply to various lithium-ion cells such as 18650 cells and prismatic cells, lithium-ion batteries, lithium-ion battery modules, lithium-ion battery packs, and so on.BONAD battery safety testing equipment complies with various standards such as IEC 62133, IEC 62133, UL 2580, UN 38.3, UL 1642, etc. For more information, please contact us, BONAD will provide you with professional technical consultation and high-quality testing equipment.
-
Product
Thermal and Mechanical Testing System
3500 System
-
The Gleeble 3500 is a fully integrated digital closed loop control thermal and mechanical testing system. Easy-to-use Windows based computer software, combined with an array of powerful processors, provides an extremely user-friendly interface to create, run and analyze data.
