Programmable DC Electronic Loads
Vary load current programmaticlly.
-
Product
PXI/PXIe 15W Programmable Resistor Module
40-254-016
Programmable Resistor Module
The 40-254-016 (PXI) and 42-254-016 (PXIe) are programmable resistor modules with 2 channels which can be set between 1Ω and 1.8kΩ with 8Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
Inductive Load Tester
4602-LV
-
There is a tendency that MOSFET has Low On Resistance so that it demands that Inductive Load Tester to have higher forcing current for measurement. The forcing current is limited by forcing voltage with previous test method. Thus it becomes difficult to test this kind of middle power range devices.
-
Product
DC Bench Power
XDL Series
-
AMETEK Programmable Power, Inc.
The Sorensen XDL series II represents the "next generation" of high performance laboratory power supplies. The XDL provides multiple ranges for increased current capability at lower voltages and uses pure linear technology. Unlike other digitally controlled units, the XDL series II provides both numeric and rotary control while the illuminated keys and display legends provide instant confirmation of settings and status.
-
Product
PC-Based Programmable Motion Controller
Motion Controller
The MAS controller is a programmable PC-based controller based on the Motion Studio software development tool.
-
Product
Electronic Surveying Compass
TOPOSENSOR
-
F. W. Breithaupt & Sohn GmbH & Co.KG
*Compact electronic surveying compass*Internal memory for storage of approx. 4.000 measurements*RS232 interface*Digital LCD readout of horizontal/vertical angles; disply 1°*Declination setting*Scope magnification 10x*Accessories upon request
-
Product
Resistive & Capacitive AC Load Bank
RCD
-
RCD AC load banks are used to test the REAL working condition of UPS, rectifier, inverter and etc who are loaded by non-linear or electronic load with non-constant resistance such as computer, networking equipments and etc. Through the accurate detection of its output and power quality, users could avoid the inadequate loading capacity or cause pollution to power grid, so as to guarantee supply security. JUNXY RCD load banks leading power factor loads are created to debug power supply system parameters such as its crest factor test.
-
Product
Load Cells
-
An array of load cells, including bending beam, tension and compression link, button, low profile, through hole, S type, cannister, tension link, and single point load cells as well as load pins.
-
Product
High Power DC Electronic Load
34000A Series（5KW~40KW）
-
34000A Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.SHORT time setting and SHORT_VH, SHORT_VL setting function, also can measure Short Voltage and Current.
-
-
Product
DC Power Supply
-
We are counted amongst the leading names in the industry, offering wide range of DC Power Supply. We make DC Power supply up to 100A for the Lab & also Industrial Purpose. Our entire product range ensures consistent performance and ensures smooth performance. We deliver them in standard configurations and are delivered in varied strength capacities.
-
Product
Load Tester for A Type dDrometers
-
A load tester for checking the spring load characteristics of ASKER hardness testers at the hardness readings of 25, 50, and 75.It is necessary to check the shape and height of the indentor, the indicating mechanism, and other parts of the hardness tester are set correctly before doing a load test. This tester is applicable to "quasi-object"models with spring load characteristics slightly different from that of object models by adjusting the reference value accordingly.
-
Product
Brush DC Drivers
-
Allegro provides a broad portfolio of safe and robust brush DC solutions. With both integrated and MOSFET gate drives our product lines are ideal for low- and high-power applications alike. Increased digital content with embedded drive algorithms simplify your implementation, while enhanced diagnostics and protection features ensure a safe and reliable solution.
-
Product
Mixed-Signal Active Load Pull System
MT1000 And MT2000 Series
-
The MT1000 and MT2000 mixed-signal active load pull systems are the best commercially proven solutions capable of performing load pull at high speeds of up to 1000 impedance/power states per minute with no limitation on Smith Chart coverage, under the following conditions:Single-tone CW and pulsed-CW RF signalDC and pulsed-DC biasTime-domain NVNA voltage and current waveforms and load linesFrequencies between 1 MHz and 40 GH
-
Product
Open-Short-Load RF calibration kits
-
Open-Short-Load RF calibration kits from Fairview Microwave are available with Type N or 7/16 DIN connectors. Type N open-short-load RF calibration kits have male or female genders, 7/16 DIN open-short-load kits are male gender. Type N open-short-load (OSL) calibration kits for RF have a minimum frequency of 0 (DC) and a maximum frequency range between 4 GHz and 6 GHz. Type N open short load kits for calibration have a maximum power handling of between 1 Watt and 2 Watts.
-
Product
High Current Electronic Load (600W-1200W)
ELCH600 & ELCH1200
-
- Low lead resistance <5m Ohm for Fuel-cell- Battery Testing- VFD display- High resolution 0.1mA/1mV- Voltage range 0V to 500V- Working mode CV/CC/CW/CR- OV/OC/OP/OT protection- Communication: USB/RS232/GPIB
-
Product
Advanced Power System - DC Power Supply, 160 V, 12.5 A, 2000 W
N6977A
DC Power Supply
The N6978A is designed for automated test equipment (ATE) applications where high performance is critical.
-
Product
Industrial Electronics Testing for Smart Devices & More
-
As more and more devices are being designed with inherent intelligence and the ability to connect and communicate, the amount and complexity of electronic content is continuously increasing for our industrial customers. They need the ability to quickly and efficiently verify proper operation of these products as they flow off the production line. Circuit Check responds to these needs by offering a wide range of industrial electronics testing solutions from consulting to complete test system and software design. We also offer adaptable support solutions to ensure proper equipment operation throughout its life cycle.
-
Product
13 GHz Programmable Attentuator
PA13
-
This device has low impedance mismatch, high bandwidth, wide dynamic range and is capable of rapid state change. The PA13 can be an attractive alternative to either the manually operated microwave attenuator switches, which are expensive and are switched very slowly, or the relay attenuators which are expensive and wear out quickly.
-
Product
Test Stands DC
-
forms e.g. B. together with an MTS750 source system, a DC meter testing device with a maximum of 40 measuring stations
-
Product
PXI 5W Programmable Resistor Module, 2-Channel, 2Ω to 52.4kΩ
40-252-033
Programmable Resistor Module
The 40-252-033 is a programmable resistor module with 2 channels which can be set between 2Ω and 52.4kΩ with 1Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Electronic Test Lead Kit
U8202A
Accessory Kit
Designed for use with the U3606A DMM and DC power supply; includes leads, alligator clips, mini grabbers, and more
-
Product
Load Measuring Pins
-
Magtrol Load Measuring Pins are temperature-compensated transducers used to measure load and force and provide overload protection. The pins are mounted into machines in place of normal shafts and fitted with strain gauges, allowing them to produce a signal proportional to the measured load.
-
Product
PXI/PXIe High Density Precision Resistor Module, 18-Channel
40-297A-010
Programmable Resistor Module
The 40-297A-010 (PXI) and the 42-297A-010 (PXIe) are 18-channel programmable resistors with a range of 1 Ω to 31 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
600W Bench Electronic Load, Dual Input 150V, 60A, 300W
EL34243A
Load Module
Keysight’s EL30000 Series bench electronic loads consist of three models, all with a built-in data logger. The EL33133A basic performance electronic load offers an economical price, a limited range, and a single 40 A, 150 V, and 250 W input. Two performance models offer additional ranges, the EL34143A single input 60 A, 150 V, 350 W, and EL34243A dual input 60A, 150V, 600 W.
-
Product
PXI/PXIe 15W Programmable Resistor Module
42-254-013
Programmable Resistor Module
The 40-254-013 (PXI) and 42-254-013 (PXIe) are programmable resistor modules with 2 channels which can be set between 1Ω and 238Ω with 1Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
Electronic Differential Pressure
Density Measurement
-
An innovative software and hardware concept makes it possible to combine any two pressure transmitters of the VEGABAR 80 series into an electronic differential pressure system to measure density. Electronic differential pressure measurement is used for measuring density change and/or for compensation when the level needs to be measured.
-
Product
Programmable Serial Device
HR-16P
-
The HR-16P is a programmable RS-232 serial device designed to control any device with a serial port based on sensing level changes (open-to-close and close-to-open, or digital high to low and vice versa).
-
Product
Universal Programmers
Uprog
-
Uprog is universal device programmers family. It uses LPT parallel port or USB for communication with PC.Graphical interface of Uprog software is very confortable in usage for programming and testing tasks. Uprog programmers have 100% universal programming socket. They allow to put independly on any pin programming voltage (0-30V), power supply (1.8-8V), ground or clock, so this flexibility allow Uprog programmers to handle any device.
-
Product
Tension Load Cells
-
These Load monitoring systems are available in telemetry/wireless (RLP), self-indicating (LLP) and cabled non-indicating (WLP) versions. Towcell a 25kN, wireless tension load cell specifically engineered for the emergency services, salvage and 4 x 4 industries. Ruggedly built and highly accurate load link style load cell dynamometers allow for force and load monitoring across a broad range of industries and applications.
-
Product
Programmable Step Attenuator, DC to 26.5 GHz, 90 dB, 10 dB steps
84906K
Attenuator
The Keysight 84906K programmable step attenuator offers coaxial measurements to 26.5 GHz in a compact, rugged design. It offers repeatability of better than 0.03 dB, excellent life (greater than 5 million switching cycles per section) and an attenuation range of 0 to 90 dB in 10-dB steps. This latest design evolution sets new standards for size and performance. High attenuation accuracy and low SWR are achieved through the use of miniature thin-film attenuation cards composed of high-stability tantalum nitride film of saphire substrate. Insertion loss is outstanding, with less than 2 dB of loss at 26.5 GHz. The compact size of the unit, 35 percent smaller than the Keysight 8495/7 (26.5 GHz) family, allows for easy integration into instruments and ATE systems.
