Programmable DC Electronic Loads
Vary load current programmaticlly.
-
Product
EMX-7XXX
Programmable Resistor Module
The AMETEK VTI Instruments EMX-7000 Series PXIe Precision Programmable Resistor Ladder modules provide four independent channels of programmable resistors. The EMX-7004 is capable of delivering exceptional stability and accuracy for any resistance value between 1 Ω to 16,383 Ω and can be adjusted in 1 Ω increments through the software application programming interface (API) or dynamic soft front panel.The EMX-7005, EMX-7006 and EMX-7007 are perfect for applications requiring higher resistance values, with programmable settings ranging from 163 kΩ to 16.383 Mohms, while the EMX-7014, 7015 and 7016 are ideal for general purpose applications not requiring ultra high accuracies.
-
Product
Load Cells
-
Morehouse Instrument Company Inc.
When high accuracy and low risk are critical, customers rely on Morehouse Ultra-Precision Load Cells. These strain gauge type load cells are often the choice for companies that want their reference standard to have the lowest possible uncertainties. Lower uncertainties allow for shorter set up times, less frequent standard changes, and fewer standards to maintain.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 8.19k Ohm - SPST
50-294-124
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-110-HI
Programmable Resistor Module
The 40-230-010-HI (PXI) and 42-230-010-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 31.5Ω with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-335-HI
Programmable Resistor Module
The 40-230-335-HI (PXI) and 42-230-335-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 201kΩ with 4Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 1.02k Ohm
50-294-021
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Dual DC Electronic Load
3330F Series（40W~250W）
-
3330F Series Dual DC Electronic Load is a two load unit in one module. Each 3330F Series module has its own control and display panel, CC/CR/CV/CP/ Dynamic modes, plug in 3300F with 150 sets Store/Recall memory which provides load set-up more efficiently，also can be remote controlled via RS232、Ethernet、USB and GPIB interface.
-
Product
Electron Sources
-
SPECS Surface Nano Analysis GmbH
To our customers in research and industry we offer a variety of sources for deposition, excitation and charge neutralization as well as analyzers and monochromators. Most of our sources originate from product lines which we have taken over from Leybold AG, Cologne, and from VSI GmbH. The X-ray monochromator Focus 500 and the UV monochromator TMM 302 are original developments by SPECS.Compliance with industry standards, a good price-performance ratio, stability, and longevity are the guidelines for our product development. We focus on standardized easy handling, user-friendliness, standardized software interfaces and safety.
-
Product
DC Converter
-
Primary switched DC converter modules are used, among other things, to generate different (consumer) voltage levels from central DC voltages, also battery-supported.
-
Product
BeeProg2C Programmer
-
Universal Programmer memory, microcontrollers and PLDs. This supports systems 78324 Beeprog2c programmer Elnec company is an excellent choice for factories and businesses servicing the electronic devices
-
Product
Load Cells
-
Whether you need general purpose, low profile or miniature cells for standard or special applications, you don't have to be an expert in force measurement, because we are. Talk to us about what sort of forces you need to measure, and under what conditions and constraints. We'll walk you through the load cell specification process, quickly and efficiently, and if we don't have what you need on the shelf, we'll be happy to customize an existing product or build a new one from scratch to meet your exacting requirements.
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 8.19k Ohm
40-294-024
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
DC Filters
-
This DC filter provides substantial noise reduction on DC power lines of up to 50V 9A. Filter provides noise suppression in both directions protecting your DC lines from noise generating by a particular piece of equipment or protecting your sensitive equipment from noise coming from DC power supply or other loads. DC filter provides noise suppression for both power lines – positive and negative, plus common-mode noise vs. ground. Filter uses plug-in terminal block for connections and mounting flanges for easy installation. Its rugged construction makes it easy to fit in many industrial tools.
-
Product
150-Watt AC/DC Power Supply; Single Output
56MS1
Programmable Power Supply
NAI’s 56MS1 is a 150 Watt AC/DC Power Supply that accepts multiple AC inputs plus a +270 VDC input. This COTS unit provides full-power, single output, at a baseplate temperature of +85° C.
-
Product
Modular DC Electronic Load
63600
-
Chroma Systems Solutions, Inc.
Chroma’s 63600 Modular DC Electronic Load is designed for testing multi-output AC/DC power supplies, DC/DC converters, chargers, batteries, adapters, and power electronic components. They are excellent for use in research, development, production, and incoming inspection applications. The 63600’s state-of-the-art design uses DSP technology to simulate non-linear loads using an unique CZ operation mode allowing realistic loading behavior.
-
Product
Bidirectional DC Power Supply
62000D
DC Power Supply
Chroma 62000D programmable bidirectional DC power supplies provide both power source and load characteristics. These two quadrant power supplies allow power from the DUT to be converted back to the utility grid and so are ideal for testing renewable energy power systems such as PV, storage, and EV inverters as well as a wide range of bidirectional power conditioning system (PCS) and may also be used as a battery simulator.
-
Product
DC Detector
-
This sensor can be used to troubleshoot any DC circuit with voltage ranging from 6-50 volts DC. It features an audio and visual alert and a sharp, rust-proof, stainless steel tip that works great for penetrating insulated wires. This sensor also features an extended ground lead with an extra-large alligator clip to ensure a good connection.
-
Product
Electronic Ballast Tester
-
LCD for displaying waveforms and parameters directly, and it includes all the functions and technical parameters of WT3000. Reports can be printed if printer is connected. It also meets the latest requirements for electronic ballasts in international standards
-
Product
DC Load Simulating Inductors
-
Osborne has developed a wide range of DC load simulation inductors that are known for the transients they produce. Osborne DC load simulation inductors are unique and innovative because they are engineered to produce a precise time constant current transient during the current charge cycle.Another distinguishing feature of our load simulation inductors is that they produce a precise voltage transient during the current discharge cycle. The resulting test circuit can be used to accurately replace real loads in a variety of circuit simulation applications.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-134-HI
Programmable Resistor Module
The 40-230-134-HI (PXI) and 42-230-134-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 102kΩ with 2Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 239Ω
40-251-013
Programmable Resistor Module
The 40-251-013 is a programmable resistor module with 8 channels which can be set between 1Ω and 239Ω with 1Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
VP-299 Programmer
-
19 000 + devices supported by programmer . TOMSAD is an official distributor of Wellon products Compatible with devices with low voltage 1.5V. Automatic start programming with the detection chip’u inserted in the stand. 40 pins zif socket
-
Product
DC Power Supply
62000P series
DC Power Supply
Chroma's new 62000P Series of programmable DC power supplies offer many unique advantages for ATE integration and testing. These advantage include a constant power operating envelope, precision readback of output current and voltage, output trigger signals as well as the ability to create complex DC transients waveforms to test device behavior to spikes, drops, and other voltage deviations.Designed for automated testing DC-DC converters and similar products, the 62000P sets a new standard for high accuracy programmable DC supplies. The 62000P Series includes 12 different models ranging from 600W to 5000W, up to 120A and up to 600V. Due to their constant power operating envelope a single instrument can provide both high voltage/low current AND low voltage/high current thereby reducing the number of supplies needed in typical ATE applications.
-
Product
Electronic Drum Latency
-
EDLM iPhone app was developed specifically for measuring latency in electronic drums. It connects to the input and output points of an e-drum system and provides automated and accurate latency measurements.
-
Product
Bore Gages - Electronic
-
Measure internal diameters and bores. Data output options available including Bluetooth.
-
Product
Programmable AC and DC Power Source
AFX Series
-
The AFX Series is a family of high power, single, split and three phase, AC, DC and AC+DC output capable Power Sources. Available models range from 6 kVA to 90 kVA with available configurations to 150kVA. Using a modern user interface for ease of use, the AFX Series is cost effective and fully programmable for both basic frequency conversion and advanced AC power line or DC power disturbance test applications.
-
Product
PXI 5W Programmable Resistor Module, 1-Channel, 1.5Ω to 472Ω
40-252-120
Programmable Resistor Module
The 40-252-120 is a programmable resistor module with 1 channel which can be set between 1.5Ω and 472Ω with 0.125Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Electronic Tire Tester
Model BTT-5700
-
The Branick BTT-5700 was created from the ground up to be the most efficient, durable and reliable electronic tire tester available. The electronic detector accurately locates flaws that may be missed using conventional methods. A visible spark occurs at the site of a flaw and the rotation stops to allow the flaw to be marked. The adjustable height platform reduces physical strain that can often lead to workers compensation claims. The BTT-5700 also features a bi-directional variable speed electric rotation motor that is whisper quiet. The auto extend/retract ramp makes tire loading easy. Hand controls are located on a locking swing arm that can be adjusted in seconds. Four air tool ports and two electric outlets are also provided so any needed tools can be kept close for improved efficiency. A high power LED light and Medium Truck Probe are also included. All probe heads require only the push of a button to change and are available to fit all common tire sizes. And, like everything from Branick, it's made in the USA.
-
Product
Automatic Programmers
-
SuperBOT is an automatic IC programmer with high performance and reasonable price for large-scale electronic product manufacturing. This programmer can automatically pick up, place, program, take out and pack up chips. SuperBOT 3 is capable of supporting most MCU, CPLD, serial and parallel NOR/NAND FLASH.
-
Product
Load Pins
-
They are used in many diverse applications including cranes, winches, agricultural equipment (such as tractors), fishing, marine, offshore, subsea, aerospace, process industries, mining, hoisting gear, elevators and floor conveyors, cable laying machinery and many others. The load information provided by the pin can be used for process control, weight/force measurement, overload protection and safety related aspects.
