Programmable DC Electronic Loads
Vary load current programmaticlly.
-
product
DC/DC Power Supply
ISM-DC-AT512-P
The ISM-DC-AT512-P is a dual output, DC/DC power supply designed for small form factor embedded systems. It features a very wide voltage input range from 10 to 50 volts DC. This allows the unit to operate with 12, 24, or 48 volt battery or distributed DC power systems. It opens up a wide array of applications including transportation, Mil/COTS, security, solar-powered, and telecommunications.
-
product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-031
The 40-297A-031 (PXI) and the 42-297A-031 (PXIe) are 9-channel programmable resistors with a range of 2 Ω to 13.6 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PCI High Density Pecision Resistor Card
50-298-131
The 50-298-131 is a high density programmable resistor card with 4 channels which can be set between 3Ω and 13.6kΩ with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PCI Resistor Card 2-Channel 2 Ohm To 65.5k Ohm
50-293-033
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Programmable AC&DC Power Supply Unit
PADS
The energy feedback type programmable AC/DC power source with energy feedback unit equipped functions of voltage adjustable, frequency adjustable, harmonic controllable, low voltage ride through simulation etc.
-
product
High Power DC Electronic Loads
63200A
Chroma Systems Solutions, Inc.
Chroma High Power DC Electronic Loads provide wider operating voltage and current ranges up to 240kW, sine wave loading, dynamic frequency sweep to 50kHz, digitizing, MPPT, an impressive front panel that tilts, and the highest accuracy available (voltage 0.015% + 0.015% F.S. and current 0.04% + 0.04% F.S.) – all with an incredibly high power density (6kW @4U).
-
product
Programable Power Supply & Programable Electronic Load
PW-8033P
*DC 0~32V / 0~3A X 2 + Fix 5V/3A*Triple Output 207 VA High Power*4 Digits, 4 Display*Programable Control, 9 Memory*Built In USB Interface*Series 0~64V / 0~3A Operation
-
product
Electronics
Electromagnetic, Signal Integrity, Thermal and Electro-Mechanical Simulation Solutions. The use of Ansys Electronics solution suite minimizes the testing costs, ensures regulatory compliance, improves reliability and drastically reduces your product development time. All this while helping you build the best-in-class and cutting-edge products. Leverage the simulation capability from Ansys to solve the most critical aspects of your designs
-
product
PCI Precision Resistor Card 9-Channel, 1Ω To 122Ω
50-297-112
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Bidirectional Programmable DC Power Supply(5kw ~ ±180kW)
FTB9000 Series
Shenzhen FaithTech Technology Co., Ltd.
FTB9000 series is a regenerative bidirectional programmable DC power supply, it is not only a stand-alone bidirectional DC power supply but also can be used as a regenerative electronic load, to absorb the consumed energy and feedback cleanly to the grid. The high-efficiency energy feedback efficiency not only saves electricity consumption and heat dissipation costs but also does not interfere with the operation of the power grid. It is widely used in high-power testing scenarios such as automotive electronics, new energy vehicles, photovoltaic energy storage, intelligent industrial equipment, battery simulation, etc.
-
product
PXI 5W Programmable Resistor Module, 2-Channel, 1.5Ω to 6.97kΩ
40-252-024
The 40-252-024 is a programmable resistor module with 2 channels which can be set between 1.5Ω and 6.97kΩ with 2Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-140
The 40-297A-140 (PXI) and the 42-297A-140 (PXIe) are 3-channel programmable resistors with a range of 2.5 Ω to 102 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
150-Watt AC/DC Power Supply; Single Output
56MS1
NAI’s 56MS1 is a 150 Watt AC/DC Power Supply that accepts multiple AC inputs plus a +270 VDC input. This COTS unit provides full-power, single output, at a baseplate temperature of +85° C.
-
product
Electronics
We develop and deliver a wide range of advanced technologies for the commercial and military electronics markets. Our portfolio includes flight and engine controls, electronic warfare and night vision systems, surveillance and reconnaissance sensors, mobile networked-communications equipment, systems integration, and environmentally friendly energy management systems.
-
product
PXI Programmable Resistor Module 2-Channel 3 Ohm to 131k Ohm - SPST
40-294-134
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Sequence Creation Software for Power Supplies and Electronic Loads
Wavy Series
WAVY is sequence creation software that supports the power supplies and electronic loads from KIKUSUI Electronics Corp.
-
product
PCI Precision Resistor Card 3-Channel, 3Ω To 22.3MΩ
50-297-154
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI Programmable Resistor Module 18x8 Bit, 0 Ohm to 255 Ohm
40-295-121-18/8
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
product
DC Power Supply, 30V, 3A
U8001A
The Keysight U8001A 30V/3A single-output, non-programmable DC power supplies is suitable for a variety of electronics manufacturing applications. With our affordable pricing, it is also well suited for usage in education labs.
-
product
PXI/PXIe High Density Precision Resistor Module, 4-Channel
40-297A-123
The 40-297A-123 (PXI) and the 42-297A-123 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 3.55 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-026
The 40-297A-026 (PXI) and the 42-297A-026 (PXIe) are 9-channel programmable resistors with a range of 1.5 Ω to 26.7 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI Resistor Module 24-Channel (no resistors fitted)
40-280-021
The 40-282 is a potential divider with up 24 separate channels. This can be used to emulate potentiometer devices, each channel having a fixed R1 R2 ratio. Additionally, the centre point can be shorted to either of the potentiometer end points.
-
product
PXI/PXIe High Density Precision Resistor Module, 4-Channel, 1.5 Ω to 925 Ω
40-297A-121
The 40-297A-121 (PXI) and the 42-297A-121 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 925 Ω, 0.25 Ω Resolution. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
1800 Watt DC Electronic Load Mainframe
N3300A
The Keysight N3300A is a full-rack width mainframe with 6-slots that accepts combinations of N330x user-installable load modules (150 W to 600 W) for easy system configuration and future reconfiguration. The N3300A holds up to six N3302A, N3303A, N3304A, N3307A load modules, or three N3305A, N3306A double-wide modules, allowing a total up to 1,800 watts of maximum power.
-
product
PXI Precision Resistor Module, 9-Channel, 2 to 6.97k
40-297-030
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Electronic Load Board 3U CPCI-S (air cooled)
056-377
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
product
Electronics Consulting
Our approach to consulting is unique. We encourage you to participate in every phase of the study. We provide you with all the information and knowledge that you need to repeat the study and perform future studies independently. Our reports are detailed and comprehensive. A consulting project may get over in a set time period but we expect our relation to continue. Our mission is to empower you through our products and services.
-
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 16.3k Ohm - SPST
40-294-131
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Electronic Load
* Fully programmable, self-contained, air-cooled solid state load.* Patented design is optimized to provide ultra-low impedance operation for fuel cell testing.* Load is compatible with AC impedance or frequency response analyzers.* Interchangeable shunts for precise operation over a wide dynamic range.* Ten built-in cell voltage monitoring inputs optional. Additional voltage monitoring inputs available.* Ethernet Interface for simple configuration and expansion!* Combine with additional Fideris™ Innovator Series™ modules to create a fully-integrated,fully-automated, customized test system.* System-wide control of all Fideris™ Test System Components using FCPower™ Software,LabviewTM, or other programming language.* Integrated hardwired Run/Standby signal.
-
product
PXI 2.5W Programmable Resistor Module, 4-Channel, 2Ω to 52.4kΩ
40-251-033
The 40-251-033 is a programmable resistor module with 4 channels which can be set between 2Ω and 52.4kΩ with 1Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
