Programmable DC Electronic Loads
Vary load current programmaticlly.
-
product
PXI 10W Programmable Resistor Module, 1-Channel, 1Ω to 31.5Ω
40-253-110
The 40-253-110 is a programmable resistor module with 1 channel which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
PXIe-6674T, OCXO PXI Synchronization Module
781037-01
PXIe, OCXO PXI Synchronization Module—The PXIe‑6674T generates and routes clocks and triggers between devices in a PXI Express chassis as well as to other PXI and PXI Express chassis or third-party instrumentation. The PXIe‑6674T unlocks the advanced low-voltage differential signaling (LVDS) trigger signals PXIe‑DStarA, PXIe‑DStarB, and PXIe‑DStarC, on PXI Express while fully supporting the PXI trigger lines. The PXIe‑6674T can generate two types of clock signals: a highly stable 10 MHz clock based on an onboard precision oven-controlled crystal oscillator (OCXO) reference and a second clock from the direct digital synthesis (DDS) clock generation circuit.
-
product
PXI 5W Programmable Resistor Module, 2-Channel, 2Ω to 52.4kΩ
40-252-033
The 40-252-033 is a programmable resistor module with 2 channels which can be set between 2Ω and 52.4kΩ with 1Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
+5 VDC to +3.3 VDC 75-Watt Converter 6U VME
44KS2
NAI’s 44KS2 is a 75-Watt DC/DC Converter that plugs directly into a standard 6U VME chassis with an 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This switching power supply accepts a +5 VDC input and converts it to a single +3.3 VDC output at 75 Watts. The 44KS2 is ideal for powering single board computers or any other devices that require +3.3 VDC.
-
product
Programmer
Gang2000
The GANG2000 Programmer is a multi-tap device that can quickly and efficiently program multiple independent target boards that use the Texas Instruments C2000 32-bit Microcontrollers from a Windows PC over a high-speed USB2.0 port. You can also use the Gang2000 during program development as a JTAG emulator.
-
product
PCI High Density Pecision Resistor Card, 6-Channel, 4Ω To 11.4MΩ
50-298-053
The 50-298-053 is a high density programmable resistor card with 6 channels which can be set between 4Ω and 11.4MΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI 2.5W Programmable Resistor Module, 2-Channel, 2.5Ω to 102kΩ
40-251-040
The 40-251-040 is a programmable resistor module with 2 channels which can be set between 2.5Ω and 102kΩ with 0.125Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
High-power Programmable DC Laboratory Power Supply (5kW~180kW)
FTP9000 Series
Shenzhen FaithTech Technology Co., Ltd.
FTP9000 series DC power supplies provide wider voltage and current output range at full power, this means both low voltage/high current and high voltage/low current devices can be tested using a single power supply. The FTP9000 series offer a high power density, with 15 kW in a 3U chassis. The standalone power ranges from 5 kW to 180 kW, voltage ranges from 80 V to 2250 V, and current up to 6120 A. For ultra-high-power applications, FTP9000 series allow for master-slave parallel up to 10 identical units, maximum output 1.8 MW, with current automatically shared.
-
product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 62.1Ω
40-251-011
The 40-251-011 is a programmable resistor module with 8 channels which can be set between 1Ω and 62.1Ω with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
PCI Precision Resistor Card 3-Channel, 2.5Ω To 773kΩ
50-297-143
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
-
product
Bidirectional Programmable DC Power Supply
IT6000C Series
The bi-directional programmable DC power supply of IT6000C series combines two devices in one: a power supply (source) and an electronic load (sink) with energy recovery. Based on these two functions, IT6000C offers the functionality of two-quadrant operation. The regenerative capability enables the energy consumed to be put back onto the grid cleanly, saving costs from energy consumption and cooling, while not interfering with the grid.
-
product
150~300W DC Electronic Loads
JT631 Series
Nanjing Jartul Electronic Co., Ltd
JT631 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT631 series load very suitable for testing power supply when produced in large quantity. Besides, JT631 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT631 series load satisfing most of R&D requirements. Moreover, JT631 series load’s special parallel operation method can satisfy the synchronous loading requirements of multi-channels output power supply and satisfy single-channel output power supply requirement for big power.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-040
The 40-297A-040 (PXI) and the 42-297A-040 (PXIe) are 6-channel programmable resistors with a range of 2.5 Ω to 102 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
UNA Programmer
MS 1604
The UNA programmer is used to program the UNA board. The UNA Programmer is a processor-based system. The UNA Programmer performs the Blank checking, Programming, Reading and Verification
-
product
Precision Programmable DC Voltage Calibrator
2701C
Designed for critical calibration lab requirements, this 4th generation contemporary 2701C design is lightweight, rugged, and at home on the production line or the engineer’s workstation.
-
product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 63.7 Ohm - SPST
40-294-111
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-034
The 40-297A-034 (PXI) and the 42-297A-034 (PXIe) are 9-channel programmable resistors with a range of 2 Ω to 102 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI Precision Resistor Module 4-Channel, 2 to 52.4k
40-297-133
This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Programmable DC Power Supply
SPD1000X Series
SPD1000X Programmable Linear DC Power Supply has a 2.8 inch TFT-LCD display, features remote computer control capability, and real time wave display. This single output design is focused on delivering high performance and ease-of-use in a small package. The SPD1168 features a high precision programmable output capable of delivering up to 16 V/8 A,the SPD1305X features a high precision programmable output capable of delivering up to 30 V/5 A and also includes a 4-wire sense function for more accurate voltage sourcing, especially for long leads or high resistance connections. There are additional output short and overload protect functions to assist in production and development applications.
-
product
1000 Watt AC/DC Power Converter, 6U VPX
VPX56H-6
The VPX56H-6 is NAI's latest high power, 1000 Watt AC/DC converter which accepts either a 3Ø 115VAC L-N inputs or a +270 VDC input. It plugs directly into a standard 6U VPX chassis with a (VITA 62) 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
product
PXI High Density Precision Resistor Module, 3-Channel, 3.5Ω to 1.51MΩ
40-298-144
The 40-298-144 is a high density programmable resistor module with 3 channels which can be set between 3.5Ω and 1.51MΩ with 2Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Electronic Boards
Computer Gesteuerte Systeme GmbH
The relay board 8AGN is a cost-effective board of the CM series, which is also used in our load modules, for example. It can be mounted on a 35 mm DIN rail. Currents up to 1 A at 30 V are possible. The maximum wire cross-section is 0.5 mm².
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1500B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-154
The 40-297A-154 (PXI) and the 42-297A-154 (PXIe) are 3-channel programmable resistors with a range of 3 Ω to 22.3 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-055
The 40-297A-055 (PXI) and the 42-297A-055 (PXIe) are 6-channel programmable resistors with a range of 3 Ω to 43.8 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Programmable Decades
Programmable, highly precise and stable resistance decades. They are used to simulate temperature sensors and to precisely set resistances. Sensors Pt-100, Pt-200, Pt-500, Pt-1000, Ni-100 and Ni-1000 in the range from -200 to +850 degrees C can be selected as temperature simulators. The temperature is entered via the keyboard or the data interface. The corresponding resistance appears at the outputs in two, three or four-wire technology.
-
product
Load Cells
For use in harsh environments, our Models T66 (bending beam),T85 and T85-T(shear beams)are manufactured fromstainless steel, fully welded and hermetically sealed to provide total environmental protection (IP68 and IP69K). The T85-Tmodel has a blind loading hole, ideal for use in platform scales.
-
product
Battery Electronics
CAES Battery Electronics provide autonomous, dissipative, and continuous cell balancing to maximize available battery capacity, and therefore battery cycle life, throughout a mission.
-
product
DC to DC Voltage Regulator
HVDR-15
The HVDR-15 is a high efficiency, high voltage step down DC to DC voltage regulator. Input voltage can be as high as 110VDC. Up to three output voltages can be pre-configured to allow up to 1A or 3A of output current. The HVDR-15 features over voltage, over current, and over temperature protection. It is offered in one, two, or three output voltage versions making it a very efficient and flexible platform for many applications.
