Sensor Testers
-
product
Non-Contact Voltage Tester
NT-303
Contact - free electrical socket indication at AC voltages between 90V-240V. Clear alarm system: flashing LED with beeper alarm.. Quick and accurate detection of circuit breaks.. Includes a small screwdriver for easy batteries replacement.. Pocket pen-type design, easy to carry and store.
-
product
High-acceleration Shock Tester
DP-1200-18
King Design Industrial Co., Ltd.
The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/- 10%.Can add spring system to reach the requirement of extra high acceleration specification.Using high-efficiency vibration-absorbing seat pad can block out possible floor resonance and protect the factory structure.Easy in operation; no complicate training course required.Module shock rubber-pads are applied per different standards independently. And the rubber-pad lifetime can be prolonged.
-
product
Sensors And Components
ION Science is a leading manufacturer of VOC gas sensors, with PID sensor technology trusted by major gas detection manufacturers globally for accurate detection of volatile organic compounds (VOCs). To the ever-growing sensing portfolio, ION Science offers Development Boards and Kits specially designed to offer OEMs at a simple, low-cost with means of integrating MiniPID sensors into existing systems and applications. Due to tightening legislation and the growing global focus on air quality, worker safety and environmental emissions are driving the requirements for a new generation of measurement and monitoring systems. The multi-award-winning Disc Pumps are now available and distributed by ION Science.
-
product
Qualification Tester
LQ404
Computer Gesteuerte Systeme GmbH
The qualification tester LQ402 is designed to support up to 12 DUTs (Device under Test), for which the loads are installed in separate load boxes. The system consists out of 3 cabinets. One is for the electronic components with the primary measurement devices and the other two hold the 12 load boxes.
-
product
Digital Temperature Sensor
ZET 7120
The ZET 7120 unit converts signal from the sensor into temperature values. The resulting temperature values are transmitted via CAN interface. Thus, the use of digital sensors releases the user from the necessity of the measuring channels setting.
-
product
Torque Tester
WDIS series
Management of various torque tools PLC and connection alsoWDIS-IP (05/5/50/200/500/1500), WDIS-RL (005/05/6/10), WDIS-IPS (05C/5C/20CL). The DIS series has become easier to use and has higher performance. Interlocking with a personal computer or PLC, the torque measurement can be managed at a higher level.Management of manual torque drivers and wrenches, management of automatic and semi-automatic tools, inspection of screw tightening and loosening torques
-
product
WAN Tester III
The Telinc WAN Tester III is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 modems,multiplexers, CSU/DSUs, T-1 CSUs, DTUs, NTUs and TIUs. It is supplied with user changeable nickel metal hydride batteries and a built-in charger.
-
product
Network Cable Testers
Companies expect their Ethernet twisted pair cabling to work flawlessly, but corners cut during design, installation and testing result in network downtime which translates to wasted resources and lost revenue. This can be avoided by cable installers that can install copper cabling systems and locate faults quickly.
-
product
Impulse Winding Tester
TH2882A-5
Changzhou Tonghui Electronic Co., Ltd.
Due to the influence of coil wire material, magnetic material, framework and manufacture technics etc., coil products (such as transformers, motors, etc.) may have defects of low insulation between coil layers, circles and leads. TH2882A series impulse winding tester, adopting high-speed sampling technique, is a new generation analysis test instrument for insulation performance of coil products.
-
product
Compression Testers
Dedicated compression testers offer low footprint test systems. Lever operated systems allows for quick and repeatable compression testing. The wheel operated system allows for more precision with hand wheel operation. The motorized compression tester allows for the most control and the highest degree of repeatability with the ability to set a constant test speed.
-
product
Oxygen Logger Sensor
NUL-205
This sensor can be used to make measurements of the level of free oxygen in air or dissolved oxygen in water. The free oxygen in air mode is used to measure changes in oxygen levels during combustion or in reactions that produce oxygen (hydrogen peroxide decomposition). The dissolved and free oxygen modes are very useful in the study of photosynthesis.
-
product
SRJ (for IBP sensors)
The MEDTEQ SRJ is a test jig to measuring the step response of IBP sensors, which can assist in testing compliance with IEC 60601-2-34 frequency response. It is also suitable for manufacturers or test labs wanting to access the raw pressure waveforms via an oscilloscope.
-
product
Conductivity-Resistivity Sensor Electronics and Integral System with PVDF Sensor
2850
The Signet 2850 Conductivity/Resistivity Sensor Electronics are available in various configurations for maximum installation flexibility. The universal mount version is for pipe, wall, or tank mounting and enables single or dual (digital versions only) inputs using any standard Signet Conductivity/Resistivity sensor. The threaded j-box version can be used with these same Signet sensors for submersible sensor mounting. It is also available as a combined integral system configuration for in-line mounting and includes a conductivity electrode in a choice of 0.01, 0.1, 1.0, 10.0 or 20.0 cm-1 cell constants. The 2850 is ideal for applications with a conductivity range of 0.055 to 400,000 S or a resistivity range of 18.2 M to 10 k.
-
product
Low-Voltage Twin-Lead Tester
69134
Tests 5-50 volt, AC or DC circuits and components.Built-in lamp glows if circuit is live.Each of the 4-1/2'' (114 mm) test leads has an alligator clip on the end.Handy pocket clip.
-
product
Belt Tension Tester
BTT2880
Main used in belt tension measurement, can also be applied to measure the tension of objects such as tapes, wires. Widely applied in industries of automobile, textile, cables, wires, plastic films, paper, printing.
-
product
Vacuum Bottle Testers
Vanguard Instruments Company, Inc.
The VBT-75 S2 is Vanguard's second generation microprocessor-based, portable, 75kV dc vacuum bottle tester. This lightweight, portable tester is designed for testing circuitbreaker vacuum bottles in the field and at the shop.
-
product
Flying Probe Testers
SPEA’s Flying Probe Testers help manufacturers of printed circuit boards to deliver top-quality products in the fastest time-to-market, avoiding fixture cost and increasing accessibility when compared to bed-of-nails testers.
-
product
Installation Testers
Offers two models that verify the safety of electrical installations in residential, commercial and industrial applications. Has been developed to carry out the following safety measurements of electrical installations in accordance with EN 61557 and DIN VDE 0100: Insulation resistance, RCD tests, Low Ohm resistance, Earth ground resistance, Loop impedance, Phase sequence.
-
product
Color / Mark Sensors
Panasonic Industrial Devices Sales Company of America
Panasonic provides Digital Color and Mark Sensors for high precision detection of any color, mark and vital indicators with high speed response times.
-
product
Portable Tensile Tester
SG-L08C
Digital Compress and Tensile testing machine.It's appropriate to testing the resistant properties of all sorts of materials such as tensile force, compression, tearing force, peel force, adhesive force, etc.
-
product
Standard RF Power Sensors
Coaxial Dynamics "Standard" line of RF Power Sensors provide DC currents proportional to the forward and reflected power flowing through the line. All models are designed to drive a 30A, 1400-Ohm meter, or provide approximately 100 millivolts across a 5K load.
-
product
Digital Meteorological Sensor
ZET 7023
The ZET 7023 weather sensor is a measuring unit with two in-built sensors one of which is responsible for measuring relative humidity and temperature, and the other one, for atmospheric pressure measuring.
-
product
Ross Flex Tester
UI-FT27
Ross flex tester is used to test the cut growth in rubber vulcanizates under continuously bend flexing in 90°.
-
product
Mechanical Load Tester
Solar modules and collectors, whether on roofs, in façades, or freestanding, are often exposed to high mechanical stress or load: A deep layer of snow or strong winds can greatly affect the materials and connections. Mechanical load test stands accurately test the durability of PV modules and thermal solar collectors.
-
product
CO₂ Sensors
SprintIR®-W
The SprintIR®-W is part of a range of CO₂ sensors designed to deliver unprecedented high-speed measurement capability. The SprintIR®-W will take up to 20 readings per second, making it ideal for applications that require individual measurements at high repetition rates or where the CO₂ concentration is changing rapidly.
-
product
CCFL Ballast Tester
WT2000A-CCFL
This tester is specially designed for analyzing the electrical characteristics of CCFL Electronic Ballast, meets the test requirements in international standard• Input characteristics analysis: measure Vrms, Irms, W, PF, Hz, phase angle Measure THD, 0 to 39th harmonic components, Accuracy: ±(0.4% reading+0.1% range+1 digit)• Output characteristics analysis: measure lamp voltage, lamp current, lamp power, oscillatory frequency, crest factor of lamp current, Accuracy: Class 2• Interface RS-232C provided for easier communication with PC for printing test report
-
product
Force Distance Tester
925
The Model 925 is a low cost force-distance tester. It communicates with a Windows™-based PC to send data into an Excel format. The data can then be viewed and analyzed in tabular or graphical format. Once in the Excel format, the data can be transferred or used in any of the multiple Excel operations. This line of displacement-force test stations has a positional resolution of 0.0025 mm (0.0001 inches). Your test department will appreciate the high accuracy readings provided over the complete travel range.
-
product
Breaking Force Tester
ZDY-02
ZDY-02 Breaking Force Tester is applied for break force test of the ampoule, lipstick, lip cream and other materials.
-
product
Force Sensors
General purpose force sensors are offered in either stud or axial mounted configurations. They are internally pre-loaded and can be used for dynamic compression, tension, and impact force measurements. Tapped mounting holes on both ends of the radial connector style support link, platform, integrated link, and free-standing installations. The axial mounted type offers protection of the electrical connector and sensor cable from potential damage during drop testing and in free-standing installations. Supplied impact caps facilitate impact and drop force measurements.





























