FFT Spectrum Analyzers
-
Product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781426-03
Signal Module
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
Product
Power Quality Analyzer
PQM-711
-
PQM-711 power quality analyzer is an advanced product for wide type of measurements, analysis and recording of network parameters 50/60 Hz and the power quality diagnostic according to European standard EN 50160. PQM-711 is an innovative model with a wireless communication Wi-Fi , which allows for automatic pairing with the included tablet, with a large 10" touch screen. Tablet allows full operating of the analyzer, live data preview and the reading and analysis of data stored in the internal memory. With this solution, the PQM-711 is an unique device that combines the advantages of the analyzer with built-in display and typical portable analyzers (known as Black Boxes).With the tablet you can very fast checked the device under test. On the other hand, you can leave the analyzer module for multi-measurements as a typical logger without display. You can very fast diagnose the machine under test using the tablet. On the other hand, you can leave the analyzer module itself for many days measurement as a typical logger without display. PQM-711 has a transient registration with a maximum sampling rate of 10 MHz (rapid changes in voltage) and control signals. The minimum duration of the registered transient is 650 ns.
-
Product
ARINC BusTools Software Analyzer
-
BusTools-ARINC is the only solution for Bus Analysis, Simulation, Maintenance and Data Logging of ARINC 429, 575, 561/6-wire, 717 and CSDB databus protocols. Simultaneously control, log and display data from a single Windows-based program on USB, PCI, CompactPCI, PCI Express, ExpressCard, PC/AT, PC/104 and PCMCIA platforms. BusTools-ARINC provides comprehensive monitoring, data logging and simulation for 100% bus loading activity.
-
Product
Infrared Analyzers
-
Teledyne Analytical Instruments
Infrared Analyzers by Teledyne Analytical Instruments
-
Product
Open Path CO2/H2O Analyzer
LI-7500DS
-
The LI-7500DS is designed for high-speed CO2 and water vapor measurements in ambient air. Lower power and maintenance requirements make it ideal for field deployments.
-
Product
ESU Analyzer
ESU-2050
-
The BC Biomedical ESU-2050 ESU Analyzer is the first instrument of its kind on the market. Designed through extensive collaboration with several of the world's leading electrosurgery generator manufacturers. It is the only ESU Analyzer on today's market with a 1% reading level of accuracy. Calibration quality analyzer; uses external precision non-inductive test loads and wide band current transformer.
-
Product
Handheld Infrared Oil Analyzer
FluidScan® 1000 Series
-
The FluidScan® 1000 series handheld Infrared oil analyzer provides direct quantitative measurement of a lubricant’s condition and plays an important role in Machine Condition Monitoring (MCM) for proactive and predictive maintenance in Reliability Management programs. It determines when oil needs to be serviced due to degradation of the oil chemistry or contamination by other fluids such as water or the wrong oil. It is compliant with ASTM D7889 “Standard Test Method for Field Determination of In-Service Fluid Properties Using IR Spectroscopy”.
-
Product
SignalShark® -Real-Time Remote Analyzer
-
Real-Time Remote Analyzer for the Detection, Analysis, Classification and Localization of RF Signals between 8 kHz and 8 GHz. Supports automatic direction finding and TDOA. Solves complex measurement and analysis tasks reliably and quickly with outstanding RF performance. Windows 10 based open platform for 3rd party applications. SignalShark exists in different incarnations. These are available as stand-alone units (table-top or in-system), single or double for installation in a 19" rack. The Remote Analyzer type is optimal for remote control applications.
-
Product
Electrical 5-in-1 Production Safety Analyzers
Model 19032/19032-P
-
Electrical Safety Test (EST) Analyzer that combines the functions of impulse test, hipot, insulation resistance and DC resistance measurements. It has 5kVac/ 6kVdc high voltage output, 5kV insulation resistance, 6kV layer short impulse voltage and 4-wire DC resistance measurement that can comply with the wound components test demands by providing maximum 10 channels output for multichannel scanning tests to save time and labor costs.
-
Product
Centrifugal Nanoparticle Analyzer
Partica Centrifuge CN-300
-
With a measurement range of 10 nm - 40 μm, the Partica CENTRIFUGE CN-300 applies centrifugal force of up to 30,000g and uses temperature control to produce accurate measurement results for a variety of samples.Developed based on customer feedback and improving upon existing and new HORIBA technologies, the result is an analyzer that provides safe and reliable operation while also being easy to use.
-
Product
UV Analyzer
AF46
-
The AF46 is a dual wavelength, high precision UV light absorption analyzer designed for inline operation to provide accurate concentration measurements with remarkable repeatability, linearity and resolution. Wavelength and optical path length can be individually configured to specific requirements for the highest accuracy.
-
Product
Ultra-Low Range Gas Filter Correlation Carbon Monoxide Analyzer
Model T300U
-
The Model T300U Trace-level CO analyzer has been developed specifically to address the challenges of low level monitoring as required, for example, in the US NCore network. Using IR absorption with a Gas Filter Correlation Wheel, the T300U is designed to allow ultra-sensitive CO measurements while still meeting the requirements for use as a US EPA compliance analyzer.The optical bench is enclosed in a temperature controlled oven, dramatically decreasing instrument noise and drift. The objective and field mirrors in the sample cell are gold plated to maximize signal to noise performance, while a temperature-controlled Nafion dryer on the inlet minimizes water interference caused by ambient humidity changes. Periodically, the T300U seamlessly corrects its baseline by routing the sample through a heated catalytic CO scrubber. This Auto Reference function corrects zero drift and reduces the effect of interferences.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T300U comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
Permeation Analyzers
-
MOCON Permeation Analyzers are used to test the gas permeability of packaging films and whole finished packages. Our analyzers provide Oxygen Transmission Rate (OTR) and Water Vapor Transmission Rate (WVTR) testing capabilities for a diverse range of materials and packages. MOCON Water Vapor and Oxygen Permeation Analyzers offer the highest repeatability and lowest limits of detection for OTR and WVTR measurements. This means better QC of your packaging processes and higher confidence in your R&D results.
-
Product
Multi-protocol USB Type-C Analyzer
Type-C Tracker
-
Protocol and Electrical Analysis Tool for Type-C Communications Standards. All-in-One: Concurrent and tightly synchronized capture of USB Power Delivery protocol, Type-C voltage tracking (Vconn, Vbus, SBU, and CC), USB 2.0, Thunderbolt 3 UART and DisplayPort auxiliary (AUX) signaling over the Type-C SBU lines, alternate (ALT) mode support for DisplayPort, HDMI, and Thunderbolt, and capture and decoding of Serial Wire Debug (SWD) protocol, UART, Serial Peripheral Interface (SPI) I2C vendor-specific protocols, and Type-C Port Controller Interface traffic over I2C.
-
Product
Linux Network Analyzer
netsniff-ng
-
Swiss army knife for your daily Linux network plumbing. The netsniff-ng toolkit''''''''s primary usage goal is to facilitate a network developer''''''''s / hacker''''''''s daily Linux plumbing. It can be used for network development, debugging, analysis, auditing or network reconnaissance. a zero-copy packet analyzer, pcap capturing/replaying tool.
-
Product
Digital Multi Channel Analyzers
-
Dual independent 16k Digital MCA available in desktop and NIM from factors Dedicated to high resolution gamma ray spectroscopy.
-
Product
LPDDR3 178-ball BGA Interposer For Logic Analyzers
W3301A
Interposer
The W3301A LPDDR3 rigid BGA interposer for LPDDR3 178-ball DRAM enables capture of simultaneous read and write traffic at data rates in excess of 1866 Mb/s. E5406A Soft Touch probes and U4201A cables connect the W3301A LPDDR3 BGA interposer into the U4164A logic analyzer module. The W3301A LPDDR3 178-ball rigid BGA interposer allows signal access to the LPDDR3 signals critical to your debug and validation effort through a U4164A logic analyzer. The probe works in existing designs and eliminates the need for up-front planning or redesign. The probe connects directly to the balls of the DRAM using a LPDDR3 178-ball riser (included) or an optional 3rd party socket (not provided), enabling operation and acquisition of LPDDR3 signals.
-
Product
HandyScope HS6-DIFF With SureConnect: 500 MS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-500XMS-W5
-
The only oscilloscope in the world that has:- SafeGround, differential input channels that can be switched to single ended.SureConnect, auto-detects a true connection between the probe tip and the device under test.- CMI interface.- USB 3.0 interface, 5Gb/s data transfer- Lowest noise
-
Product
Bus Analyzer
FireSpy® 4430b(T)/4830b(T)
-
The FireSpy4430bT and FireSpy4830bT as well as FireSpy4430b and FireSpy4830 bus analyzers are DapTechnology's latest 4-bus IEEE-1394 protocol analyzer. Based on the 4th generation FireSpy analyzer architecture the FireSpy4430b(T)/4830(bT) is the most advanced 1394 test equipment in the market. The FireSpy4430b(T)/4830(bT) in fact combine four FireSpy analyzers in one single instrument. They comprises a significantly more powerful on-board processor and improved connectivity to the host.
-
Product
Nitrogen Oxides & Ammonia Analyzers
-
Teledyne Analytical Instruments
Nitrogen Oxides & Ammonia Analyzers by Teledyne Analytical Instruments
-
Product
Comprehensive Oil Analyzer For Engines
MiniLab EL
-
Engine oil analysis is a reliable and mature non-destructive testing (NDT) technique used to monitor the condition of the engine in development, on the production line and for in-service maintenance. High performance reciprocating engines and jet turbines are complicated mechanical systems with many high speed moving parts.
-
Product
Static Code Analyzer
HelixQAC
-
For over 30 years, Helix QAC has been the trusted static code analyzer for C and C++ programming languages. With its depth and accuracy of analysis, Helix QAC has been the preferred static code analyzer in tightly regulated and safety-critical industries that need to meet rigorous compliance requirements. Often, this involves verifying compliance with coding standards — such as MISRA and AUTOSAR — and functional safety standards, such as ISO 26262.
-
Product
Trace & Purity Oxygen Analyzers
-
Industrial Gas can be separated into bulk gas, speciality gas and ultra-high purity (UHP) gases. Within the PST Group we have a range of analyzers to measure oxygen as well as other impurities.
-
Product
MD analyzer
-
King Design Industrial Co., Ltd.
MD AnalyzerProduct Function Operation Display32dot*128dot/STN-LCD+LEDUse knot and SET.ESC-SW to choose menuUSB memory/printer communication portOKNo voltage A contact, contact capacityOnly less than 1 A 30 VDC or 0.5 A125 VAC resistive loadInstant DisconnectionDC 12 V±10%1A/100mA /10mA±10%1A:1Ω~50Ω10%100mA: 5~500±10%10mA: 50~5kΩ±10%0.1us~99.9us
-
Product
Power Quality Analyzer
-
Weshine Electric Manufacturing Co., Ltd
Three Phase Power Quality Analyzer High Precision
-
Product
High Performance Power Analyzer
2503AH
-
Vitrek’s High Performance Power Analyzer provides high bandwidth to 500kHz and typical 0.05% accuracy. The measurement channels can be configured independently (asynchronous or synchronous) allowing the instrument to be setup for your specific needs.
-
Product
Impedance Analyzer 1MHz-20Hz
IA1000
-
Frequency range20 ~ 1MHzFrequency accuracy0.005%Frequency resolution0.001% in all frequency rangeTest signal level0.05 ~ 2.0 VrmsTest signal resolution0.001 VrmsTest signal output impedance100ΩImpedance Z range; basic accuracy0.0000Ω ~ 99.99
-
Product
Advanced Serial Protocol Analyzer
-
Most data networks are complicated, not just the hardware and network issues, but also the high-level protocols that devices use to communicate; and to make things even more complicated, many manufacturers have incorporated proprietary protocols for their devices. Integrating different devices and protocols within a data network is always the most challenging task for system integrators, firmware / software developers, and site engineers. From the simplest loopback test to complicated checksum calculation and sophisticated firmware and GUI software development, the 232Analyzer is designed to tackle all these challenges.
-
Product
Antenna Impedance Analyzer
TZ-900 AntennaSmith
-
Analysis Parameters: SWR, Complex Impedance, R+jX, reflection coefficient, Smith Chart. 0.2 - 55 MHz • SWR
-
Product
Analyzer
-
Water and wastewater treatment still require analyzers for on-line measuring, justifying their presence next to commonly more reasonable in-situ sensor systems. Especially for utmost precise water analysis – with for i.e. effluent monitoring of wastewater plants requiring automatic calibrations and/or adaption as well as standard DIN procedures for analysis – analyzers are applied. Besides the measuring instruments also the sample preparation is of great importance.
