Polarization Extinction Ratio
a measure of the degree of polarization. AKA: PER
See Also: Fiber Optic Cable Test
-
product
High-acceleration Shock Tester
DP-1200-18
King Design Industrial Co., Ltd.
The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/...show more -
product
Ionization Test Set
PFK-105
- Ionization Test Kit for Measuring Offset Voltage and Discharge Times- Includes a Field Meter, Charge Plate Monitor, ±1000 Volt Charger and Decay Timer- Balance Ionizers per ANSI/ESD SP3.3 Periodic Verification- Measure Ionizer Decay time as per ANSI/ESD S3.1 and ANSI/ESD SP3.3.- Measure Body Voltage Generation and Decay- Evaluate Ionizers and Packaging Materials- Includes a fixture to hold the PFM-711B, CPM-720B and PDT-740B as one- Molded Carrying Case with Foam Insert Included
-
product
Mixed-Signal Active Load Pull System
MT1000 And MT2000 Series
The MT1000 and MT2000 mixed-signal active load pull systems are the best commercially proven solutions capable of performing load pull at high speeds of up to 1000 impedance/power states per minute with no limitation on Smith Chart coverage, under the following conditions:Single-tone CW and pulsed-CW RF signalDC and pulsed-DC biasTime-domain NVNA voltage and current waveforms and load linesFrequencies between 1 MHz and 40 GH
-
product
PXI-7953, Virtex-5 LX50 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module
780340-01
Virtex-5 LX50 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module—The PXI‑7852 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. T...show more -
product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, 1 kV Isolation
43-752A-112
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
Paperless Recorders
Rishabh Instruments Pvt. Ltd.,
LCD Touch Screen with user interface panel. Comes with 3/ 6 programmable input channels. Have 6/ 12 alarm outputs and 4/ 8 digital outputs. Visualization of measurements in graphical forms. Compatible with MS windows CE operating System. CE Approved and safety as per European Norms.
-
product
SINE (Sinusoidal) Targets & Arrays
Sinusoidal Target Arrays have been recognized as a superior test method for a variety of applications, from moiré contouring to reliable MTF Evaluation of materials, lenses, cameras, and electro-optical systems (Follow the hyperlink to learn about using Sinusoids for MTF eval). Sinusoidal Pattern Arrays are manufactured on two different materials for both reflective and transmissive applications. Because of the inherent limitations of reflective materials, the maximum spatial frequency of the r...show more -
product
Rotational Flow Demonstration Kit
The rotational flow demonstration kit detects the rotational position using the MCU’s on board data transfer controller (DTC) function, a form of state machine, while the MCU’s core is in stop-mode state. This ensures that the average power consumption is kept as low as possible, with IAV (average current) at 4.5 microampere (μA) and a 32 sample burst per second. The flow demonstration kit senses the flow direction and volumetric flow rate of water and gas, and can also detect reverse flow. The demonstration kit is applied using an active inductive method. Two coils are used to sense the rotational position of a part-metalized disk, and a third coil is used to generate a reference signal.
-
product
2-channel, 12 bit, 50 MS/s Waveform Digitizer
ATS9130
ATS9130 is a 2-channel, 12 bit, 50 MS/s waveform digitizer capable of storing up to 8 Million samples per channel of acquired data in its on-board memory or streaming acquired data to motherboard memory.
-
product
Oxygen Sensor Tester and Simulator
ST05
The sensor signal output is shown in real time on the bar graph, while a 2 digit alphanumeric display shows the sensor output cross count per second. By pressing the ?Test? button and performing a snap throttle acceleration of the engine, it tests the response time of the sensor and shows a pass or fail result within seconds. Two buttons allows for simulation of rich or lean conditions to monitor response of the engine control module.
-
product
Through Hole/ Donut Load Cell Compression Only
THC SERIES
Our THC Series through hole donut load cells offer an outside diameter of 2.00 inches and up to six different through hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
product
16 A/D Channels (±25 mA); 16-bit SAR per channel
ADG
Module ADG features 16 channels with up to 16-bit SAR A/D converters, simultaneous sampling. The maximum programmable, expected full-scale range input for the ADG module is -FS to +FS or 0 to FS; 25, 12.5 mA respectively. The A/D converters have programmable sample rates of up to 200 kHz.
-
product
Diode Pumped Actively Q-switched Lasers
NL120 Series
NL120 series electro-optically Q-switched nanosecond Nd:YAG lasers provide up to 10 J per pulse with excellent stability. The innovative, diode‑pumped, self‑seeded master oscillator design results in Single Longitudinal Mode (SLM) output without the use of expensive narrow linewidth seed diodes and cavity‑locking electronics.
-
product
Hamburg Wheel-Tracking Tester
The Hamburg Wheel-Tracking Tester is used to test submerged, compacted Hot Mix or Warm Mix Asphalt specimens as per standard.The device consists of a reciprocating wheel that is rolled over the specimens while measuring the rate of permanent deformation. A constant load of 705 N ±4.5 N is applied to the specimens with a sinusoidal wheel speed of 1 ft/sec in a constant temperature controlled water bath up to 70 °C (± 1.0 °C). An LVDT jig is used for continuous measurement of permanent deformation...show more -
product
Interface Card
XMC-WMUX
Alta Data Technologies’ XMC-WMUX interface module (PCI Express Mezzanine Card for Carriers and Single Board Computers or Carriers) is a single or dual-channel (A-B Redundant = 4 Busses per Channel/Wings) WMUX card supported by the latest software technologies.
-
product
AOTF-NIR Spectrometers
Brimrose’s rugged and high-performing on-line NIR process spectrometers deliver fast-response and multi-component analysis for a variety of process applications for many industries, including pharmaceutical, food & dairy, chemical, polymer, petrochemical, agricultural, seed, pulp & paper, and olive & grape industries. The AOTF technology enables Brimrose spectrometers to scan very fast (up to 16,000 wavelengths per second) and without moving parts.
-
product
PCIe/104 4×4 or 2×2 mPCIe Carrier Boards
104e-mPCIe-4
The 104e-mPCIe-4 is a Type 1 or Type 2 PCIe/104 carrier board designed to support up to four PCI Express mini cards, in either half or full lengths. In addition the board supports up to two mSATA devices (via dip-switch selection on Type 2 PCIe/104 stacks only), and all four sockets support USB, SMBus, and wireless mPCIe devices — including micro-SIM sockets, per socket, for cellular (WAN) use.
-
product
6000 Series Analog I/O Modules
Series 6000 analog I/O modules condition, amplify, filter and digitize signals from virtually any transducer. All modules have conditioning & amplifier per channel and nearly all modules allow for setting bridge completion, shunt calibration, transducer power, gain, etc. individually per channel. Following the conditioning/amplifier stage, multi-pole Bessel or Butterworth analog filters are provided on each channel and can be set or bypassed individually by program control. A number of the m...show more -
product
Energy Meters
Rj-7600
The Rj-7610 Single Channel Energy Meter works with a variety of probes – pyroelectric, silicon, and thermopile – to measure true energy per pulse from single-shot to 40 Hz, picojoules to Joules, UV to far-IR. Sets of 10 or 100 pulses can be statistically analyzed (mean, minimum, and maximum energies, standard deviation), and data can be transferred to computer via the IEEE-488 GPIB computer interface or using the 0-10 VDC analog outout.
-
product
acA3088-16gm, Monochrome GigE Vision, 6 MP, 16 FPS Area Scan Camera
787065-01
Monochrome GigE Vision, 6 MP, 16 FPS Area Scan Camera - The acA3088-16gm is a Monochrome Basler Ace GigE Vision Camera with a 6 MP resolution and a maximum image acquisition speed of 16 frames per second. … The acA3088-16gm uses a IMX178 sensor and is quality tested and calibrated for high performance and reliability. This camera can be used with NI hardware and software to build machine vision systems.
-
product
Grinding Tool Dynamometer
UIG-17
Unitech Scales And Measurements Pvt. Ltd
Unitech offers tool dynamometers to measure cutting forces on various machines like lathe, drill, milling machines. All three direction forces are measured simultaneously and displayed. Tool dynamometers are useful to study, analyse the optimum feed, speed and depth of cut on different materials. The dynamometers are also available in various capacities as per customer requirement.
-
product
Barometric Pressure Sensors
Accurate within 1.5 % across a pressure range of 15 to 115 kPa (4.43 to 34.96 in Hg). Long-term non-stability has been measured continuously indoors and in natural conditions (with sensors mounted inside a datalogger enclosure) for multiple sensors and is less than 0.5 % per year. Temperature effects on signal are less than 1 % across a wide temperature range (-20 to 50 C).
-
product
Industrial and R&D Furnaces
We at Tempsens manufacture both Industrial and Laboratory Furnace and Ovens for varied applications which include sintering, annealing, tempering and calcination. The furnaces and ovens manufactured come in varied sizes and volume as per the application requirement.
-
product
Panel-mount Type pH Meter (Four-Wire Transmission, Pulse Proportional Control)
HP-480PL
HP-480PL industrial pH meter is a pH meter with a pulse proportional control function, which can drive a pulse pump directly.It connects pH sensor and measures pH and temperature in the sample water.As the HP-480PL has a high injection resolution per pulse, it can be used to control a pulse pump as part of a system for processing involving fine control of pH values, for example controlling the pH values of microscopic or small samples.
-
product
H2S Trip Amplifier Module
TA202A
The TA202A is a single-channel H2S Trip Amplifier Module for use with our H2S Intelligent Sensors. It is designed to monitor H2S in parts per million (ppm) levels and provide status indication and alarm outputs.
-
product
MCB Tripping Current Characteristic Test Bench
The SCR Elektroniks 12 station MCB Tripping Characteristics Test Bench is optimally designed to verify the Tripping Characteristic of MCBs as per clause 9.10.1 of IEC 60898 (Also mentioned in Indian Standards IS 8828). The bench essentially comprises of Servo Controlled mechanism to set and maintain desired current (against incoming mains fluctuation) and a Micro controller based master controller unit plus timer, which governs the entire sequence of operation making it a stand-alone system once the user connects the MCB and configures the test parameters.
-
product
Pulse Generator
Traction Wheel Assembly
The complete and ready-to-install system converts linear travel/speeds to square-wave pulses/frequencies. • Square-wave frequency output, NPN open-collector • 5-28 VDC powered • 1 to 1,270 pulses per revolution (PPR - specify when ordering) • Optional bi-directional (quadrature) output models • 3 models: black neoprene rubber, smooth polyurethane, and diamond knurled aluminum tread
-
product
NMR Precision Teslameter
PT2026
Nuclear Magnetic Resonance is the most precise technology to measure magnetic fields, and the PT2026 is the most precise NMR magnetometer on the market. In optimal conditions, it achieves a precision of under ten parts per billion! But precision is just one of the features brought by the PT2026: high fields, robustness to inhomogeneous fields, 33 Hz measurement speed, improved search time – the list goes on. The key is an instrument design, using modern RF and computer technology. The result is an NMR magnetometer that opens up a host of new application areas. Magnetometer Gaussmeter
-
product
1310/1490/1550 Nm DFB-LD For Fiberoptic Communications
RV2X6376A Series of directly modulated laser (DML) diodes deliver 25 Gbps x four wavelengths as the light source in 100 Gbps optical transceivers that enable high-speed communications inside 4.9G and 5G LTE base stations, and between data center routers and servers. The RV2X6376A Series are the industry’s first industrial-temperature (-40°C to 95°C) DML diodes that support full 25 Gbps speed (per individual laser) without cooling.
-
product
PC/104 8-Channel Smart Sensor Interface
518
Measures thermocouples, RTDs, strain gages, thermistors, 4-20 mA, voltage and resistance 8 high-accuracy differential input channels Integral sensor excitation Exclusive pulsed excitation minimizes sensor self-heating Configurable sensor type per channel Fully electronic calibration Low power
