Waveform Monitors
View a video signal's electronic pattern.
-
product
Clamp type AC Current Sensor／for Power Monitor
ZCT-33
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 0.1A～150A*Current measurements of feeder
-
product
Arbitrary Waveform Generators
M531
The M531 is a single channel USB arbitrary waveform generator compatible with USB 2.0 and USB 1.1 interface. The generator has two outputs: both generate same waveform, but with different peak-peak voltage. The low level output has 50ohm output impedance and maximal peak-peak voltage of 9V. There is no external power supply required to enable low level output (it is powered from USB bus).
-
product
Solar Energy, PV Monitoring
Apogee silicon-cell pyranometers feature a monocrystalline silicon-cell detector that has the same spectral response as a PV module. The sensors quantify shortwave radiation being harnessed as electricity.
-
product
Broadcast Control and Monitoring System
Cerebrum
As a complete Broadcast Control System (BCS), Cerebrum gives you control over your most critical broadcast operations. Accessible via one application, the system’s powerful and highly customizable interfaces allow you to control, configure and monitor any broadcast environment the way you want. Cerebrum is designed to be robust in both small to large infrastructures and adapted for SDI and IP, offering you a scalable solution that is ready for today’s and tomorrow’s operations.
-
product
PoE Voltage Monitor Detect & Verify
PE-400
PE-400 is specific to test and verify PSE or Ethernet outlet either a standard/active PoE or a NON-standard/passive PoE to avoid damaging Non-PoE device as well as monitor and display available Voltage simultaneously. It built-in PoE interface controller to trigger on 802.3 af, at and bt switch and verify standard PoE type either 802.3 af or 802.3 at, and power source either End or Mid or both, and power polarity as well as display voltage values. The operational voltage which should be measured when installing a new PoE system or when you troubleshooting an existing system.
-
product
Waveform Amplifier
TS250
The TS250 Waveform Amplifier is a one of a king instrument perfect for amplifying signal generators. It is designed to amplify voltage, power or current for while driving heavy (low ohmic) loads. The TS250 offers eight voltage ranges to choose from ±10V to +65V. The TS250 output up to 6A peak current. To obtain higher current, parallel connect two or more TS250 in as shown in the Application Section.
-
product
Vibration Condition Monitoring
PROTOR
PROTOR provides a complete hardware and software solution for vibration monitoring of rotating machines. Acquisition subsystems monitor the machinery and are networked to a central server. Realtime and historical data can be accessed on the server or remotely via a LAN, WAN or VPN. Data and reports are available in graphical and numerical forms.
-
product
PXI 34x4 Signal Insertion and Monitor Matrix
40-525A-001
This is a PXI signal insertion and monitor matrix with switched pass thru connections on both X and Y axis. It is also availablein a 16x4 format and can be used for signal insertion and monitoring purposes on connections between the UUT and test system. Each pass thru connection from LX to X can be open or closed to allow the programmatic disconnection of the signal to check the response of the UUT. The matrix can be used to connect test equipment, such as a DMM or scope, to monitor the pass thru signals via Y connections while the LY connections can be used to insert a fault condition or insert external signals. When external signals are injected the LX connections can be opened and the LY connections closed.
-
product
T3AWG2K Series - 16-bit Dual Channel Arbitrary Waveform Generator
T3AWG2K Series
The T3AWG2K series consists of two affordable dual-channel arbitrary waveform generators, 16-bit vertical resolution, 6 Vpp output voltage (50Ω to 50Ω), 128 Mpts/ch memory, a maximum sampling rate of 600 MS/s and a maximum sine wave frequency of 150 MHz. The T3AWG2152-D mainframe adds 8 synchronized digital channels to the analog outputs, ideal for debugging and digital design validation.
-
product
Portable solution to monitor
MOSS HYDROSTATIC
The MOSS reads, stores and displays the pressure and temperature values during a hydrostatic endurance test.
-
product
Control, Monitor, Security and Power Management for ATEs
Subset of 6TL's FastATE modules designed for the control, monitoring, security, and power management of ATEs (automated test equipment).
-
product
C/Ku Band Satellite Monitoring
SCL-3412
C/Ku Satellite Monitoring System (SCL-3412) is designed to intercept International/national telecom carriers, GSM A/Abis links and IP Carriers over satellite which are using C, Ku, X or Ka-Band. In order to reduce the manual effort and time consumed in the analysis of the carriers, system is integrated with Satellite Carrier Analysis module, which automatically performs the scanning on the selected spectrum and provide the list of carriers along with their payload type (i.e DCME, GSM or IP) and characteristics parameters. This provides great help to take decision for monitoring of the carriers of interest.
-
product
Industrial Touch Monitors
With the latest touchscreen technology, our industrial monitors are designed to streamline and automate daily operations, enhancing operational efficiency. These monitors provide smooth user interaction, an unbeatable visual experience, and durability that meet various industrial applications’ demands. ADLINK's open-frame and true-flat industrial touch monitors offer superior quality, making them ideal Human Machine Interface (HMI) applications in industries like manufacturing, public transport, hospitality, and retail where smooth user interaction is essential.
-
product
Precision Studio Monitor
Amie
Amie unleashes your creative power by extending the accurate translation of the Meyer Sound Acheron screen channel loudspeakers to smaller studio environments.
-
product
Arbitrary Waveform Generator
SDG7000A
SIGLENT’s SDG7000A is a family of dual-channel Arbitrary Waveform Generators that feature up to 1 GHz bandwidth, a maximum sample rate of 5 GSa/s, and 14-bit vertical resolution. It can generate arbitrary waveforms point by point with a maximum 2.5 GSa/s sample rate and vector signals with a maximum of 500 MSa/s. It also has the ability to generate a variety of signals such as continuous wave, Pulse, Noise, PRBS patterns, and a 16-bit digital bus. It supports the generation of complex signals such as modulation, sweeping, bursting, and dual-channel copying/coupling/tracking and superposition. The outputs are user selectable for differential or single-ended connections and support a maximum output range of ± 24 V. The instrument can ensure a large amplitude under high-frequency which eliminates an external power amplifier in some applications and addresses a wider range of requirements.
-
product
Air Gap Monitoring & Analysis
Solutions for air gap monitoring in order to plan maintenance prior to reduced operating efficiency or damage from magnetically induced heating or rubbing between the rotor and stator.
-
product
Temperature & Humidity Monitor
A humidity sensor (or hygrometer) senses, measures and reports the relative humidity in the air. It therefore measures both moisture and air temperature. The warmer the air temperature is, the more moisture it can hold.
-
product
PCIe 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 2 Channels
M2P.6561-X4
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
product
Area/process radiation monitoring
Monitors gamma and beta rays/ neutron with high accuracy and reliability. *Each monitor is controlled with central control system and alarm is given when the measurement exceeds alarm level. Area monitors and dust monitors.
-
product
Vacuum Quality Monitor Systems
The 835 VQM is a mass spectrometer that operates from UHV to 10-5 Torr and accurately measures the gases in the vacuum chamber. The 835 VQM Differential Pump System delivers the advantages of the 835 VQM at higher pressures. The VQM system consists of an autoresonant ion trap mass spectrometer gauge, a VQM Controller and VQM Viewer software that that converts raw data into actionable information. The system is ratiometric, meaning that it determines the ratio of each gas to other gases in a vacuum chamber. It is usually coupled with a total pressure gauge to provide partial pressures of each gas as indication of the quality of the vacuum in the chamber.
-
product
High Voltage Waveform Digitizer Family
PXD731x/PXD70xx
The PXD731x High Voltage Waveform Digitizer family features up to two 100MS/s simultaneously sampled input channels with 16Bit resolution, input voltages up to ±250V and a bandwidth up to 50MHz. Every digitizer channel has its own 2MB memory which allows up to 1 million samples. Data can be acquired before and after the trigger event with a programmable sample counter, that controls the number of data points. All PXD731x High Voltage Waveform Digitizer family devices have a high common mode rejection ratio (CMRR).
-
product
Radar solution for stockpile level monitoring
After extracting, metal ore, rock, or coal is transported via conveyor belts to large stockpiles or bulk storage facilities. With OndoSense radar technology, the fill and volume level of the stockpile can be reliably and accurately measured – even in conditions of dust, smoke, strong temperature fluctuations, or vibrations.
-
product
Industrial Standby Battery Monitoring Systems
Batteries are the power storage medium for all Power Rectifier and UPS Systems. Modern Rectifiers and UPS control systems generally supply the user with only a summary of the condition of the associated power systems, however Battery Monitoring systems specifically measure, record and analyse the individual cell and battery module parameters in detail.
-
product
PXIe-5450, 145 MHz Bandwidth, 16-Bit, 128 MB, I/Q PXI Waveform Generator
780419-01
PXIe, 145 MHz Bandwidth, 16-Bit, 128 MB, I/Q PXI Waveform Generator—The PXIe‑5450 is a 145 MHz, dual‐channel arbitrary waveform generator optimized for I/Q communications signals. It is an ideal instrument for testing devices with I/Q inputs, or as the baseband component of an RF vector signal generator. The PXIe‑5450 also features onboard signal processing (OSP) functions that include pulse shaping and interpolation filters, gain and offset control, and a numerically controlled oscillator (NCO) for frequency shifting. The PXIe‑5450 also features advanced synchronization and data streaming capabilities.
-
product
Load Monitoring Units (LMUs)
Magtrol's Load Monitoring Units are used for measuring load, force and weight from signals generated by strain gauge transducers. Specifically designed for use with Magtrol's Load Measuring Pins and Load-Force-Weight Sensors, the LMU Series provides excitation voltage while conditioning the bridge output signal. Each unit contains DIP-switches and jumpers for greater flexibility and complete adaptability
-
product
Low Concentration Monitor- Sulfuric Acid/Hydrogen Peroxide
HF-700A
The HF-700A stabilizes hydrofluoric concentrations on the order of ppm in diluted sulfuric acid and hydrogen peroxide to enable continuous measurement and allow effective process management of the removal of the polymer residue following the etching process.
-
product
Battery Monitoring System
S5
BTECH's benchmark product designed for a wide variety of applications (UPS/Telco/Switchgear), the S5 can collect data from any battery type including cells with the highest amp hour rating (4000+), and the S5 systems will record all battery parameters.
-
product
Systems for Oil Quality Monitoring
*Reliable monitoring of oil contamination*Reliable machine and plant protection by permanent oil moisture monitoring
-
product
INOmini Monitoring
Choose from a wide selection of Inovonics’ INOmini monitoring options and combine them for a customized solution that fits your unique needs. INOmini products come in two sizes - the 1/3-Rack and ½-Rack - depending on the model.
-
product
20Hz Injection Kit Monitoring System
Signals & Systems India Private Limited
The Display used to monitor the 20Hz and 50Hz current passing through NGT transformer. This could help to monitor the stator earth fault and could record the current every minute. The current shall be displayed in milliamps for both 20Hz and 50Hz. If an earth fault occurs in the generator star point, the 20 Hz voltage drives a current through the fault resistance. The current can be measured using clamp-on CT which would be clamped between load resistor and NGT. It gives an indication of the current values are lower or higher than the set threshold.
