Waveform Monitors
View a video signal's electronic pattern.
-
Product
Device Current Waveform Analyzer, 1 GSa/s, 14/16-bit, 2 Channel
CX3322A
-
The CX3322A is a 2-channel model for engineers and researchers who just need one or two current waveform measurements at one time. Using a single channel current sensor (CX1101A, CX1103A) and a passive prove interface (CX1151A) enables power measurements. The bandwidth and the memory depth per channel are option and can be selected from 50 MHz, 100 MHz and 200 MHz, and 16 Mpts, 64 Mpts and 256 Mpts, respectively. The number of channels is not upgradable, but upgrade products for both bandwidth and memory depth options are also available for customers who need more performance after purchasing the product. You could also minimize the initial investment for later upgrade with this affordable 2-channel model.
-
Product
Radar solution for stockpile level monitoring
-
After extracting, metal ore, rock, or coal is transported via conveyor belts to large stockpiles or bulk storage facilities. With OndoSense radar technology, the fill and volume level of the stockpile can be reliably and accurately measured – even in conditions of dust, smoke, strong temperature fluctuations, or vibrations.
-
Product
TOC-L For Monitoring A Microscopic Algae Biomass
-
Biomass is considered a prospective new energy source. The dry weight method has been typically used to determine the amount of microscopic algae in biomass. However, Shimadzu proposes a new method, one that is rapid, easy, and accurate, utilizing the TOC-L total organic carbon analyzer.
-
Product
Microwave Monitor w/ Vinyl
A100p
-
This single-range, RF power measurement instrument is designed to operate in the 2.45 GHz range. Used by field service engineers, engaged in the repair and maintenance of commercial and domestic microwave heating equipment, its primary function is the detection RF microwave energy leakage.
-
Product
External Pyrometric Camera for Combustion Thermal Monitoring
PYROSCAN-U
-
Pyroscan-U is specifically designed to perform thermal monitoring and mapping of any object inside a kiln, furnace, boiler or reactor, while looking at the area of interest through a standard window, from outside the combustion chamber. This megapixel pyrometric camera captures both visible and infrared HDR (High Dynamic Range) images of the burning zone.
-
Product
BenchLink Waveform Builder Pro Software
33503B
-
BenchLink Waveform Builder Pro software eliminates the need for tedious programming and makes custom waveforms fast and easy.
-
Product
Test Cell Vibration Monitoring System
-
The Test Cell Vibration Monitoring System is a complete package for monitoring dyno vibration levels generated during engine testing. This system was design to prevent catastrophic dyno failures.
-
Product
ABex Current Sense Module for Six Channel UUT Supply Monitoring
ABex TM-406 Current Sense
-
The ABex TM-406 is a six-channel shunt current measurement extension. It’s designed to work in combination with the Konrad ABex TM-501 and PXI-501.Each of the six shunt current measurement units have a passive measurement shunt, an overcurrent protection, a sense bridge relay and the possibility to route the quiescence current to an ABex measurement device TM-501 with PXI-501.In addition, the ABex TM-406 features 8 isolated digital outputs (IDOs), and 12 measurement inputs, which can be routed to the analog bus.
-
Product
SpaceWire Monitors
-
This section details the 4Links range of high-performance test equipment that is used to monitor SpaceWire networks. These devices are attached to your SpaceWire systems and then can be accessed via Gigabit Ethernet, using the standard TCP/IP family of protocols, so that they can be controlled remotely (for instance, by partners collaborating on a mission).
-
Product
Portable Monitoring Receiver and RF Recorder
IZT R3301
-
The IZT R3301 is a portable receiver with an integrated server for data recording. The receiver is optimized for recoding of RF signals in frequently changing environments. The RF characteristics of the IZT R3301 are identical to the IZT R3000 series. # HF-VUHF-SHF receiver# frequency 9kHz...3GHz (3...12GHz option)# continuous spectrum recording of 24 MHz bandwidth, IQ recording with 20 MHz
-
Product
Branch Circuit Monitor
-
Multiple branches of load can be monitored togetherCan group the device as 3 phase load and single phase loadFaster communication through RS485 port (Modbus protocol)Simultaneous sampling of Volts and AmpsAccuracy Class 1.0 as per IEC 62053-21 & Class 0.5 as per IEC 62053-22 StandardsDisplays more than 25 parameters
-
-
Product
Audio Monitor
TM3-3G Smart
-
The TM3-3G Smart with full feature set is a compact and versatile out-of-the-box solution for metering, deembedding and monitoring of 3G-SDI audio signals using a 4.3“ touch screen for vertical or horizontal use. The TM3-3G Smart‘s flexible user interface allows for quick and simple preset selection as well as setting the monitoring level.
-
Product
Monitor / Annunciator
RTP-1
-
The RTP-1 Monitor is a general purpose annunciator. Designed for 19 “ rack installations, the RTP-1 is complete with a noise immune filter. The ten point RTP-1 features latching memory. Easy to install and easy to operate, this low power monitor has front panel plug-in replaceable LEDs for indication and a single system Test and Reset buttons.
-
Product
AM Open Path FTIR Air Monitoring Systems
-
AM Open Path FTIR Air Monitoring Systems bring the versatility of multicomponent analysis and the immediacy of real-time results to a variety of field applications. Now you can avoid the "hit or miss" guesswork of point sampling and the inaccuracy and delays of "bag and carry" offsite analysis.
-
Product
Snap-on RF Current Monitoring Probe
TBCP2-250
-
The TBCP2-250 is a snap-on RF current monitoring probe. The probe has a very flat response with a 3dB bandwidth of 250 MHz and is characterized over the frequency range from 30kHz to 300 MHz. Upon request, it can also be supplied with a test protocol covering the frequency range 1 kHz to 350 MHz. The aperture of the RF current monitoring probe is 32 mm. Its transfer impedance is > 12 dB Ohm in the range from 700 kHz to 300 MHz.
-
Product
Analyze, Monitor and Control
Analysis Pack
-
Blue Cat's Peak Meter Pro plug-in will tell you everything about your audio levels. Blue Cat's FreqAnalyst Pro and FreqAnalyst Multi plug-ins provide extremely smooth spectrum and frequency content analysis. Finally, the StereoScope plug-ins series let you visualize the stereo image of your audio content in details.
-
Product
Personal Safety Gas Monitors
-
Teledyne Gas & Flame Detection
Want to protect your staff with high-end portable gas detectors? Discover Teledyne Gas and Flame Detection gas detection solutions.
-
-
Product
PXI Monitored Multiplexer, Single 128-Channel, 1-Pole
40-619-401
Multiplexer Module
The 40-619-401 is a high density PXI 2 A multiplexer module in single 128-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC.
-
Product
Leakage Current Monitor
LCM500
-
The Doble LCM500 Leakage Current Monitor can measure condition while a surge arrester is still in service, measuring the quality of the metal oxide blocks and helping manage the risk of failure.
-
Product
Indoor Air Quality Monitor and Controller
VAT930-CO2/VAT930-CO2-VOC88
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
indoor air quality monitor and controller ( temperature meter. humidity meter . CO2 meter.VOC meter).
-
Product
Vault Gas Monitor
SMC 2400
-
The SMC 2400 Vault Gas Monitor detects combustible and carbon monoxide gas leaks to reduce the hazard of gas explosion and to maintain personnel safety. The monitor offers the gas detection functions required by telecom site managers including uninterrupted power supply, long-life sensors, five alarm relays, and both audible and visual alarm indication.
-
Product
Programmable DC Load Current Waveform Generator
9923
-
9923 application software can be used to edit arbitrary waveform, providing electronic load simulation different sink current conditions
-
Product
Environmental Noise Monitors
-
Noise is one of the most complained about aspects of the environment, as not only does it have the potential to affect quality of life, it can also be difficult to monitor and therefore control. This type of noise is generally called environmental noise. There are many man-made sources of environmental noise, such as wind turbines, industrial sites, roads and traffic etc. If you are looking for equipment to measure noise in the workplace, look at sound level meters.
-
Product
2 Channel IV Analyzer / Source Monitor Unit
E5263A
-
Keysight E5262A and E5263A 2ch IV Analyzers are the low cost solution for current-voltage characterization. The E5262A and E5263A support two channels of SMUs (Source/Monitor Units) for voltage/current sourcing and voltage/current measurement with the best in the class current measurement performance as low as 5 pA. The Easy EXPERT group+ GUI based characterization software is furnished and available on your PC to support all the tasks required in the characterization from the measurement setup to the data analysis. Powerful integration of SMU's versatile measurement capabilities and GUI based characterization software makes the E5262A and E5263A the best solutions for characterization and evaluation of two or three terminal devices such as materials and active/passive components with uncompromised measurement reliability and efficiency.
-
Product
Regulators, Monitoring, Sensors And Flow Control
-
All of the products in Parker's extensive pump and flow control product lines, from pumps and valves to motors and motion controllers, share a common heritage of advanced technology applied to meet the specific needs of our customers. In every instance and for every application, Parker components and systems are engineered to deliver precise and reliable control.
-
Product
Wrist Strap Monitors
-
Single conductor (more commonly called single wire) ESD wrist strap monitors detect capacitance. These simplified monitors sense the input connection but do not discern precision resistance. They also offer additional value by monitoring the worksurface (ESD Mat) and the ground connection. The built-in LED offers local visual alerts, and a small piezo buzzer offers a nice clear audible alert to the operator at the bench.
-
Product
RF Safety Monitoring
fieldSENSE 2.0
-
LBA's FieldSense 2.0 personal RF safety monitors are an effective and economical means to monitor the strength of electromagnetic (RF) fields from wireless cell phone towers, microwave ovens, television stations, and other common workplace RF sources between 50 and 6000 MHz, E-field and H-field (sensed as a plane wave). The Personal RF Monitor is essential RF safety equipment in complying with FCC, OSHA, Canadian and other workplace rf safety requirements.
-
Product
Clamp type AC Current Sensor／for Power Monitor
ZCT-23
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 0.1A～120A*Current measurements of terminal feeder
