-
product
Thermal Controlled Chucks & Plates
TOP Cool
Mechanical Devices newest innovation in thermal testing. Each TP system contains a thermal chuck or thermal plate and a self-contained thermal control unit.The TP chuck and platforms is a breakthrough product that introduced the use of refrigerant for active cooling & heating of wafers and other components with no need of chiller, CDA, or consumable and expensive refrigerants such as liquid nitrogen and liquid carbon dioxide. It can be a perfect replacement system in the industry for uncompromising thermal and mechanical performance with a temperature ranging from -60 to +220°C.
-
product
PXIe-4357 , 20-Channel, 24-Bit PXI Temperature Input Module
782118-01
20-Channel, 24-Bit PXI Temperature Input Module—The NI PXIe‑4357 input module provides integrated data acquisition and signal conditioning for 2‑, 3‑, or 4‑wire resistance temperature detector (RTD) measurements. It offers both high-speed and high-resolution modes. It provides per channel software-programmable configurations and automatically scale measured data into engineering units.
-
product
Data Logger for Temperature Humidity and Pressure
DSR-THP
Simultaneously measures and logs temperature, humidity and pressure Support out-of-limit alarm as well as on-line linear calibration High precision of 0.5hPa in the full range of 500.0a~1100.0 hPa In compliance with ISO17025, GLP and aerospace engineering practices, etc
-
product
Stress screening test chambers for temperature and climate
TS and CS series
Our based on the modular concept of the standard range of temperature and climatic stress screening test chambers allow you through increased compressor and large fan performance very high temperature change of up to 30 K / min with conventional refrigeration, or to 70 K / min with liquid nitrogen. These devices allow you to very quickly determine the load limits of your test object in fast motion.
-
product
Extra Temperature Up To 120°C (248 °F) Inductive Sensors
Contrinex Extra Temperature Up To 120°C (248 °F) Inductive Sensors
-
product
High Temperature Wettability Tester
6200Z
This device is a test device that evaluates the wetting stress generated between a plate/round bar and molten metal in an inert gas atmosphere by the wetting balance method.It is possible to analyze not only the quality of wetting but also the wetting phenomenon from the obtained wetting curve.
-
product
Remote Slab Sensor and Outdoor Temperature Sensor
CHV-RSS
The CHV-RSS is a remote temperature sensor designed for use with select Crestron thermostats. Ideally suited for concrete slab, under floor, or any outdoor installation, the CHV-RSS is an extremely accurate temperature sensor potted within a rugged waterproof stainless steel sleeve.
-
product
High Temperature Absolute Pressure Transducers
Our high temperature Baratron® capacitance manometers are controlled to temperatures of 150°C or higher for use use in demanding semiconductor manufacturing vacuum processes such as metal etching and nitride film chemical vapor deposition (CVD).
-
product
Temperature and Humidity Regulator
H3431-2
Relative humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Three two-state inputs.
-
product
Relative humidity, temperature sensors
T3111
Relative humidity, temperature sensors at probe on 1 meter cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
Temperature And Humidity Cabinet
UI-E14
Temperature And Humidity Cabinet is used to provide constant temperature humidity test condition for certain period to know the certain environmental conditions effect on the sample.
-
product
High Temperature Aging Environmental Test Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's High Temperature Aging Chamber is widely applied for automotive parts ,electronic and electric products ,components and materials by constant high temperature reliability test.
-
product
Local Discomfort Temperature Probe
TP3227K
Temperature probe composed of 2 independent probes, Pt100 sensor used for measuring local discomfort due to vertical thermal gradient.
-
product
Temperature Cycling
Reltech provides a full capability for Temperature Cycle testing as part its full turn-key solution to package level qualification testing. Our Temperature Cycling system type Espec TSA11-A, two zone (-65°C to +200°C) vertical movement system, provides an exceptional recovery time of less than 5 minutes without the need for any auxiliary cooling.
-
product
RTD Based Temperature Data Logger
RTDTemp101A
The RTDTemp101A is one of MadgeTech's newest data loggers. It is part of a new series of low cost, state-of-the-art datalogging devices. MadgeTech has taken the lead in offering the most advanced, low cost, battery powered data loggers in the world today.
-
product
RTD Temperature Indicator
CM2-TR
CM2-TR RTD Temperature Indicator has been designed in simple operation and 4 digital 20mm LED display with economic cost.They are can be programmed by buttons that are hidden in front panel.They are also available to option relay output and an analog output or RS485 (Modbus RTU Mode) communication.
-
product
Temperature and Humidity Duct Probe
T0213
Relative humidity, temperature sensors at 150mm stem. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
4 Digit Temperature (RTD) Meter (1/32 DIN)
CS3S-TR
● Measuring: Pt100/Pt1000● Accuracy: ±0.1%● Display range: -1999~9999● Dimension: 1/32 DIN (48x24mm)● High stability and reliability
-
product
Universal, Dual Input, High Performance HART Temperature Transmitter
SEM310 MKII
The SEM310 is a universal programmable HART temperature transmitter which accepts most commonly used Pt100, thermocouple, mV and slide-wire sensors and generates an industry standard (4 to 20) mA transmission signal
-
product
Temperature, Humidity, Bar. Pressure Transmitter
T7311-4
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Built-in pressure sensor.
-
product
Compressed Air Temperature and Humidity Regulator
H3021P-2
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
Walk-in Environmental Chamber for Temperature Humidity Test
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's walk-in environmental chamber for temperature humidity testing is perfectly meet the large size test application that require high temperature and high humidity. The walk-in chamber is constructed with structural steel, so it is able to test the large components and products. Various optional function available for different test standard and requirement.
-
product
High and Low Temperature Humidity Chamber
GDJS/GDJW
•The chamber is produced by SUS304 Steel, the temperature keeping material is produced by Polyurethane hard foam and ultra-fine fibre glass, the doorframe heat insulated by Double high temperature aging silicone rubber door sealing strip. •The temperature controller is used by Korean TEMI display in English/Chinese and German Siemens PLC, it can be communicated to PC via RS-232. The temperature accuracy is 0.1℃ and humidity is 0.1%R.H •The temperature sensor is platinum PT100 Ohms/MV resistor •The heating system is full separately system which produced by Nickel chromium alloy electric heating type heater •The cold system is applied by fully enclosed fan cooled single-stage and cascade refrigeration mode, the compressor is from France TECUMSEH brand which can allow you get after sales support from many countries •The cyclical system is applied by High temperature low noise air conditioning type motor and Multi blade centrifugal wind wheel •The safety self-protection function include Electric leakage, short circuit, over temperature, motor overheating, compressor pressure, overload, over-current protection •Working Power: AC380V±10% 3phases and frequency 50Hz/60Hz •Working Environmental: Temperature is 5℃～+30℃ Humidity ≤85%R.H
-
product
High and Low Temperature
FB1.5V
Reduce the floor space needed for reliable temperature testing with a Bemco FB1.5V high and low temperature chamber. Easily maneuverable, this chamber provides an industry leading 2712 cubic inches of workspace. A long list of available options allows you to modify the chamber for almost any use.
-
product
Temperature, Humidity, Bar. Pressure Transmitter
T7311-2
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Built-in pressure sensor.
-
product
cRIO-9038, 1.33 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, Kintex-7 160T FPGA, and Extended Temperature, 8-Slot CompactRIO Controller
783850-01
1.33 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, Kintex-7 160T FPGA, and Extended Temperature, 8-Slot CompactRIO Controller - The cRIO-9038 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. You also can use the Mini DisplayPort to add a local human machine interface (HMI) for application development. The cRIO-9038 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, two USB host, one USB device, and two RS-232 serial. Additionally, the cRIO-9038 supports an extended temperate range. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
product
In-situ Wafer Temperature Monitoring
CI Semi's family of noncontact temperature monitors (the NTM line), offers high end pyrometry products for the measurement of wafer temperatures during process. CI Semi’s flag ship of the line, the NTM Delta, incorporates real-time, same point emissivity measurement and compensation making it the ideal solution for in situ monitoring for processes such as RTP, CVD and PVD. The NTM family is sold to leading tool manufacturers.
-
product
Temperature and Temperature/Humidity Test Chambers
G-16 Elite
Russells G-16 Elite Series temperature and temperature/humidity chambers represent one of our pre-engineered environmental chambers. This model has a chamber volume in 16 cubic feet or 439 liters. Click for a complete overview highlighting the features and benefits of our Elite Series as well as other standard model sizes to meet your needs
-
product
Burn-in or Rapid Temperature Cycling Chamber
KDL Series
The Bemco KDL series is designed for production testing of electronic circuit boards and completed electronic systems. They accept Bemco KDLC Carts that have a working area of 42 wide by 60 high by 48 deep suspended on insulated runners and casters 11 inches above the test area floor.
-
product
Compact Temperature Calibrator
CTC Series
AMETEK Sensors, Test & Calibration
CTC Series Compact Temperature Calibrator from AMETEK Sensors, Test & Calibrations is engineered for “advanced simplicity,” incorporating a number of useful features that greatly extend the range and functionality of the popular temperature calibrator. The CTC Series offers an easy-to-read, full-color display with improved navigation that provides easy access to the calibrator’s latest features. The CTC Series now contains an auto step function with up to 12 preset temperature points, an optimized switch test with automatic up and down test runs, assisted manual calibration using pre-defined temperature points, and memory to store up to 5 calibration processes.
