Load Cell Simulators
generate a precise mV/V signal to assure load cell amplifier, tester, readout and display set up.
See Also: Load Cell Test, Load Cells
-
Product
Load Cell Power Supply
MODEL PSMR
-
The PSM-R is a self contained AC power bridge excitation supply. This device consists of a low interwinding capacitance AC transformer and a high stability adjustable linear regulator designed specifically for driving transducer bridges. DC excitation is adjustable from 4 to 15 volts output and is capable of supplying 0 to 150 mA in output current. It features remote sensing to eliminate line drop errors and very low noise. It can also be used as a high quality voltage source or reference in many applications. AC input requirements are 105 to 125 VAC at 60 Hz.
-
Product
Beam and Singlepoint Load Cells
-
We have trimmed all the non-essential fat off these load cells, however you can be sure that nothing has been trimmed from the actual load cells, they are precision tested and certified to meet all the exacting requirements on the downloadable technical specifications shown below.
-
Product
Electronic Loads
-
AMETEK Programmable Power, Inc.
Electronic loads have found a variety of applications ranging from power converter testing to current modulation. A large range of power sources can be tested using an electronic load from converters, inverters and UPSs to electrochemical sources such as batteries and fuel cells.
-
Product
LED DC Electronic Load Simulator
3340G Series（150W~300W）
-
Each 3340G Series module has its own control and display panel, LED/CC/CR/CV/CP/ Dynamic modes, plug in 3300F with 150 sets Store/Recall memory which provides load set-up more efficiently，also can be controlled intranet via RS232、Ethernet、USB and GPIB interface.
-
Product
Solar Simulator for Concentrator Cells
-
Optosolar offers solar simulators with continuous light for small area solar cells (ca. 10mm x 10mm). depending on the cell size, the concentration ratio can exceed 1000 suns. Special designs cover low concentration on large area wafers (156mm x 156mm), as well as line focus applications (e.g. 8mm x 156mm at 8 suns). Flashlight Solar Simulators have the advantage of negligible temperature change to the solar cell. For this reason, they are often used for very high concentration ratios or for multijunction cells in a solar simulator with adjustable spectrum.
-
Product
Electronic Loads
SLM AC/DC
-
AMETEK Programmable Power, Inc.
From the leader in programmable power products, Sorensen introduces the SL series electronic loads which offer the best value with the most flexible platform. A wide range of loads are available from 75-1800W with both DC and AC input in benchtop, modular and standalone form factors.
-
Product
Electronic Loads
-
PeakTech Prüf- und Messtechnik GmbH
Can be used for important test procedures in quality assurance as well as e.g. testing of power supplies and control units, batteries, fuel and solar cells. For precise load control for various purposes, this device offers load control according to constant voltage (CV), constant current (CC), constant load resistance (CR) or constant power (CP) with a highly precise resolution of 1mW, 1mV, 1mΩ and 1mA. The device also offers additional test modes, e.g. the battery test or the dynamic test. The PC interface and software offer the option of implementing freely programmable test sequences with data evaluation.
-
Product
Working Electrodes for Flow Cell
-
Our working electrodes for flow cell are mounted in blocks of PEEK. This resin protects the electrodes from external noise and allows researchers to utilize them regardless the content of mobile phase of HPLC because of their hardness and organic slovent-resistance. Glassy carbon is usually chosen for the redox reaction study on liquid chromatography. Platinum, Gold, Carbon paste and Nickel electrodes are utilized for special purporses.
-
Product
Solar Cell Simulation
Setfos
-
Easily calculate the short circuit current, open circuit voltage Voc and fill factor with Setfos. Tweak the layer stack and add light scattering layers for enhanced absorption. Optimize for AM1.5 or specific wavelength bandsElectrical IV curvesCurve fitting & parameter extractionAC simulation and transient experiments like photo-CELIVAdvanced device physics: SRH-recombination, excitons, ... Design anti-reflection coatings or transparent cells
-
-
Product
Simulation
-
Synopsys' high-performance simulation products help engineers find design bugs faster and achieve timely coverage convergence to create high-quality designs.
-
Product
PCI Strain Gauge Simulator Card, 4-Channel, 1.5k
50-265-404
Strain Gauge Simulator
Designed to simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. It provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Cell Stand
CS-3A
-
The CS-3A Cell Stand is adopted with CHI series Electrochemical Analyzers and other apparatus directly. The cell is enclosed in a Faraday cage to reduce electrical interference. A built-in gas control allows purging a sample. Gas line is provided to purge next sample, while analyzing the present sample separately, thus increasing productivity. Magnetic stirrer allows for controlling the mixing of the sample for experiments requiring mass transport of electrolyte or analyte to the electrode surface. Cell top positioner with detachable cell cap allows easy removal and replacement of the cell vial as well as the electrodes for rinsing, cleaning, and replacement.
-
-
Product
Solar Array Simulator
Simulator
Among other things, solar array simulators are required for testing satellite power supplies. An SAS (Solar Array Simulator), consisting of an interconnection of several Solar Array Simulator modules, maps the solar panels and displays the individual strings connected in parallel. Optionally, the individual SAS modules are monitored by a Second Level Protection, so that the test object is not damaged in case of errors with the voltage sources. Additional circuitry is implemented via project-specific test modules. The signal path to the DUT can be separated, e.g. for dynamic current measurements.The Keysight Solar Array Simulators used were specially developed for satellite applications and cover the significantly higher requirements regarding the control speed of MPP tracking compared to terrestrial applications.
-
-
Product
Liquid Dielectric Test Cell
LT-4123
-
The LT-4123 Liquid Dielectric Test Cell is designed for testing the quality of materials such as the insulating oils used in transformers and the resins used in the manufacture of thermosets. With the LT-4123 Liquid Dielectric Test Cell, users can measure the AC loss characteristics and permittivity of liquids. The data gleaned from these measurements are used to set quality benchmarks for fluids during testing and manufacturing.
-
Product
Bulk Electrolysis Cell
-
This cell has been developed in order to perform a complete electrolysis. The carbon working electrode is a reticulaed form that provides with sufficient surface area to gain the rate in electrolysis.
-
Product
Load Pins
-
When overload protection and/or load indication is to be installed in a conveyor, crane or other device, the PIAB SLC is the ideal solution. The PIAB SLC Load Pin easily replaces the existing shaft at an equalizing pulley or in other parts of the construction. The PIAB SLC Load Pin should be installed as close as possible to the force/load for best accuracy. Both the PIAB SLC Load Pin and the PIAB LCA Amplifier are designed to withstand extreme environmental conditions for a long operation time.
-
Product
Multi-channel Battery Simulator
FT8340
-
Shenzhen FaithTech Technology Co., Ltd.
The FT8340 series is a high precision, multi-channel, dual quadrant programmable battery simulator.The current of the simulator can be charged and discharged，and supports various fault simulations, which can not only meet the requirements of BMS testing, but also meet the ATE testing of consumer electronics products.There are at most 12 channels in a device, and each channel is electrically isolated, which is convenient for users to use in series. The built-in upper computer software is easy to operate, flexible and easy to use. It supports single channel programming operations, multi-channel editing operations, and multi process programming operations.
-
Product
Low Profile Compressive Load Cell
CCLP-1.0
-
Low Profile Compressive Load Cell – 0.5t to 20t
-
Product
Simulation And Analysis Software
fcXplorer Analyzer
-
Avionic Interface Fiber Channel Simulation and Analysis Test Software, fcXplorer, is an easy-to-use graphical user interface for Fiber Channel Simulyzer modules. fcXplorer is designed for troubleshooting, optimization, planning and configuration of fiber channel data. The low and high level protocol analysis offers acquisition, filtering, time stamping and interpretation of Fiber Channel data traffic and generates statistics.
-
Product
Load Cells
-
Load cells are electronic weight sensors whose purpose is to receive the electrical excitation caused by a certain weight applied to the scale or balance and transmit it to a weight indicator . The load cell is an essential component in any scale or electronic balance and they come in different models and specifications. A Wim load cell is essential for a weighing system where precision, durability and a fair price are required. WIM-Systems manufactures a wide variety of load cell models, one for each need, in addition to offering all the advice you need to choose the model that best meets the particular needs of your weighing system and always backed by WIM-Systems quality and technology.
-
Product
Solar Simulator
Unisim
-
TS-Space Systems is the first company to pioneer the use of metal halide sources in solar simulators for photovoltaic testing. The high temporal stability and close spectral match combined with the ability to control the output spectrum via multiple separate wavebands means the Unisim solar simulator is the only solar research tool designed for the accurate measurement of multiple junction devices, including the new generation of four junction devices. As with all our Unisim solar simulators, they exceed the ASTM, IEC and JIS international standards for spectral match and temporal instability. Using the latest HMI and halogen luminaire technology, the Unisim solar simulator provides a highly stable area of illumination. The simulators also use cutting edge filter technology in order to provide the best spectral match available for AM0 and AM1.5. Further to this, the spectrum can be achieved via two, three or four separate spectral wavebands which allows a high degree of spectral control for research and development. Product support is very important to us. Training is provided at our premises where customers can take advantage of one-on-one tuition with the instrument designers and learn how to operate and maintain their tools. Extensive support via phone and email for the full lifetime of the instrument is included with every TS-Space Systems product.
-
Product
Modbus Slave Simulator
ModSim
-
ModSim32 is a very simple but powerful application for simulating data from modbus slave devices. ModSim is an MDI application which allows you to define multiple blocks of data points which may then be accessed from a connected modbus master.
-
Product
Load Cell Tester
-
Xiamen Elane Electronics Company, Ltd
Large six-digit LED display < Easy to use and small in size < Accuracy of 0.005%FS/10ppm < 2 channels CH0 : -12mV/V~+12mV/V, with resolution 0.1uV/V CH1 : -1.6mV/V~+4.8mV/V, with resolution 0.01uV/V < Four user selectable output units (N, kgf, lbf and mv/V) < Peak Hold function to capture and holding the peak value for the immediate or later reference < Clear key to clear the peak value < Presence of tare key and foot switch to zero the display (tare function) < Great for monitoring and testing load cell characteristics (repeatability, linearity, creeping, temperature drift, etc
-
Product
Measurement & Simulation
-
Highland Technology offers a wide array of tools for measurement, simulation, and control. Tachometers, thermocouples, RTDs, precision voltages, current loops, strain gauges, and more can be measured or simulated by Highland's products.
-
-
Product
Photovoltaic Array Simulator
PV8900 Series
Simulator
Keysight’s photovoltaic (PV) simulator includes the hardware and software to test a single maximum power point tracking (MPPT) inverter accurately. Test PV voltages up to 2000 V and 60 A with a single supply. DG9000 Series software licenses are available to test string inverter with 4-, 8-, or 12-MPPT channels. Most string inverter solutions test one MPPT channel at a time — leading to test inaccuracies. Keysight's DG9000 advanced PV inverter software can test up to 12 MPPT channels simultaneously.
-
Product
PCI Strain Gauge Simulator Card, 4-Channel, 350 Ohm
50-265-014
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
