Load Cell Simulators
generate a precise mV/V signal to assure load cell amplifier, tester, readout and display set up.
See Also: Load Cell Test, Load Cells
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, V/I Readback, 1 kV Isolation
41-752A-113
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Load Cells for Weighing
-
HBM provides the optimal Load Cell or Load Sensor for your application. Beam Load Cells: The All-Rounders For Weighing Technology. Ring-Torsion Load Cells: Low Profile And Powerful. Canister Load Cells: Maximum Capacities Up To 400 t. Single Point Load Cells: The Standard in Scales Manufacturing. Digital Load Cells: Ideal For Dynamic Weighing. Weighing Modules: Pre-assembled For Tank And Silo Weighing.
-
Product
Portable Range Threat Simulators
Simulator
The Textron System's PRTS™ and HPRTS™ are medium and long-range, programmable, ruggedized Radio Frequency (RF) test and training tools. Our PRTS family of range simulators delivers high-fidelity environments for training ranges.
-
Product
Beam Load Cell
EST-70
-
Technopark Automation & Control
The EST-70 Shear Beam Load Cell is commonly used on platform, hopper weighing and pallet weighing applications. It is low cost and available in capacities from 500 kg to 2000 kg.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, V/I Readback, 750 V Isolation
43-752A-011
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXIe Battery Simulator Module, 4-Channel, 5 Amp
43-754-011
Battery Simulator
The 41-754-011 and 43-754-011 are 4 channel battery simulators, capable of supplying up to 8 V and 5 A per channel. The channels are fully isolated from ground and from each other allowing series connection to simulate batteries in a stacked architecture. The isolation barrier (1000 V channel to GND and 750 V channel to channel) allows the module to be used as a battery stack representative of those used for vehicle propulsion..
-
Product
Load Cells
-
Instron is the only testing system manufacturer that designs and builds its own load cells, ensuring exceptional accuracy, stiffness, and alignment across a wide measurement range. Produced at Instron’s High Wycombe, UK facility, each load cell is temperature-compensated and calibrated to international standards for outstanding repeatability. Backed by the largest commercial deadweight stack in the U.S., Instron’s calibration process delivers precision that often exceeds industry requirements—providing reliable, traceable performance for even the most demanding materials testing applications.
-
Product
Load Cell Tester
LCT-Ultimate
-
Industrial Measurement Systems Ltd.
This most advanced Load Cell Tester model LCT-Ultimate is a stand-alone hand-held device that was especially designed for full trouble shooting of strain-gage based load cells. The LCT-Ultimate can check all common types of standard load cells that are available on the market:
-
-
Product
S-Type Load Cells
-
S-Type Load Cells take their name from their shape – as you can see from the images below – they are in the shape of the letter “S”. These load cells are commonly used in tension applications; mechanical-to-electrical scale conversions as well as weighing applications including cranes etc.
-
-
Product
Load Cells
-
We make it our business to stay on top of emerging industry demands so that the load cells we provide help you meet your ever-changing test requirements. Our broad selection of competitively priced load products will help you meet the most demanding test and measurement requirements. Used in automotive, aerospace and defense, R&D, and process control applications, our drop-in replacement load cells are designed to provide years of dependable performance.
-
Product
Load Cells
-
A load cell is a sensor which transforms the load or force applied to it into an electrical signal. Load cell sensors are based on the strain-gauge principle i.e. a sensor whose resistance varies with applied force. They are the most widely used as load transducers in all areas of weight measurement from retail scales, the process industry and medical applications.
-
Product
Cell Solar Simulator
QuickSun® 130E
-
QuickSun 130E exceeds the ordinary Class A criterions of IEC904-9 ed. 2 with clear margin providing enhanced IV characteristics accuracy. The applicable test methods and procedures are inspected by SGS Fimko Ltd in order to guarantee the compliance and traceability not only with the above standard but also with IEC904-1 ed. 2 which specifies the IV measurement conditions.
-
Product
S Beam Load Cell
-
Futek Advanced Sensor Technology, Inc.
FUTEK S Beam Load Cells (Tension/Compression) offer a compact design for a variety of applications. Available in standard and metric, the S Beam Load Cell series provides accuracy, compact design features, overload protection (select models), and a wide capacity range to choose from. S Beam Load Cells are also commonly known as Z Beam Load Cells or S Type Load Cells.
-
Product
PXI Millivolt Thermocouple Simulators
Series 41-760
Simulator
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 16 or 8 channelseach channel providing a low-voltage output across two connector pins capable of providing 20mV with 0.7V resolution, 50mV with 1.7V resolution and 100mV with 3.3V resolution, covering most thermocouple types. These thermocouple simulators use two wire outputs with a remote output reference sense to ensure the modules deliver accurate low-level voltages, even if the system has common mode voltages present. In addition, each simulation channel is also able to provide an open circuit setting to simulate faulty wiring connections to a sensor.
-
Product
Load Cell Amplifier
-
Xiamen Elane Electronics Company, Ltd
: 0-50 degrees. Humidity: 30 to 80 percent, non-condensing.Power Supply Requirements:Power Supply voltage: 9 volts DC.Operating current: 5mA, plus bridge current.Bridge Input:Excitation voltage: 5 volts.Bridge Type: Full Wheatstone Bridge.Voltage Output Range: From 0 volts to 4.3 volts.
-
Product
Load Cells
-
For use in harsh environments, our Models T66 (bending beam),T85 and T85-T(shear beams)are manufactured fromstainless steel, fully welded and hermetically sealed to provide total environmental protection (IP68 and IP69K). The T85-Tmodel has a blind loading hole, ideal for use in platform scales.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, Simplified Current Sink, 750 V Isolation
43-752A-902
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Load Cell Transducer
-
Unitech Scales And Measurements Pvt. Ltd
Force can be measured by different methods, one of the most effective and accurate method is by using strain gauge based load cells. Four Transducer class strain gauges are bonded on the specimen and are connected in the form of Whetstone Bridge. The specimens are of different types depending on the requirement such as S, column, beam, ring, shear beam, binocular etc. UNITEH’S Load Cells are used for wide applications rite from commercial weighing scale to industrial process controlling, R & D applications and educational institutions. UNITECH’S manufacture load cells from 1Kg to 100Tons for compression or tension or universal (Compression and tension) applications. We also undertake custom built load cells for specific requirement and for OEM users.
-
-
Product
Load Cells and Sensors
-
Our high quality load cells and sensors are used for materials testing and force measurement all over the world.
-
-
Product
Dual Port Simulator Fiber Channel PCI-X Module
PCI-X-FC4 Simulyzer
Simulator
The modules are available as a single-function board - for analysis or for simulation / data generation - but also as a full-function board for simultaneous analysis and simulation. By simply upgrading the firmware / software, a single function board can become a full function board without having to purchase new hardware.
-
Product
Standard Shackle Load Cell
SS-3.0
-
The DLM Standard Shackle Load Cell is a high strength marine grade cable connected Load Cell. Manufactured from industry leading Crosby or GN Shackles along with a stainless steel load pin.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, V/I Readback, 1 kV Isolation
41-752A-111
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
DC Load Simulating Inductors
-
Osborne has developed a wide range of DC load simulation inductors that are known for the transients they produce. Osborne DC load simulation inductors are unique and innovative because they are engineered to produce a precise time constant current transient during the current charge cycle.Another distinguishing feature of our load simulation inductors is that they produce a precise voltage transient during the current discharge cycle. The resulting test circuit can be used to accurately replace real loads in a variety of circuit simulation applications.
-
Product
S-Type Load Cells
-
S-Type load cells are low-cost and high performance side mounted load cells suitable for a number of weighing and general force measurement applications. They come with a 6-foot strain relieved integral cable with pigtail leads that are stripped and tinned for electrical interface.
-
Product
Load Cell Indicators
-
Procter & Chester Measurements Ltd
The instrumentation will power the load cell. The mV/V signal coming back from the load cell is converted by the indicator and displays the force in a unit (e.g.: Kg, kN, lb – customers choice). The indicators within this range are encased so that the operator can either use it on the move (if battery powered) or be a permanent fixture, e.g.: wall mounted.
-
Product
PXI Strain Gauge Simulator Module 2-Channel, 1K
40-265-202
Strain Gauge Simulator
The 40-265 is a strain gauge simulator that simulates the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. It provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
