PCI Backplanes
-
Product
PCI Express Card
PCIe-ADIO16-16F
-
The PCIe-ADIO16-16F is a 16-bit resolution A/D & D/A card with two simultaneous 1MHz A/D converters, having a total of either 16 single ended, 8 differential, or 8 single ended and 4 differential inputs. Each channel can be independently software configured to accept any of 7 input ranges. Four analog outputs with 5, 10, ±5, ±10, and ±2.5V ranges are provided.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 1.02k Ohm
50-294-021
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 2.5Ω To 1.81kΩ
50-298-022
Programmable Resistor Module
The 50-298-022 is a high density programmable resistor card with 9 channels which can be set between 2.5Ω and 1.81kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI 32x4 2Amp High Density Matrix Card
50-528-001
Matrix Switch Module
The 50-527, 50-528 and 50-529 are a range of PCI single pole matrix cards supporting either 64 or 128 crosspoints using electro-mechanical relays. They are capable of switching voltages up to 300VDC/250VAC and current up to 2A.
-
Product
CAN/FlexRay/Differential Bus PCI Fault Insertion Switch - 4 Channel
50-200-004
Fault Insertion Unit
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
Product
PCI 64xSPDT Reed Relay Card
50-110A-121
Reed Relay
This is the 64xSPDT version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
PCI To Star Fabric Module
51-921A-001
Remote Control Interface
The use of the StarFabric interface operating at 2.5Gb/s minimizes the impact on system speed. The PCI interface of the 51-921A supports both 32 bit and 64 bit operation and backplane speeds of 33MHz and 66MHz, ensuring the highest speed operation under all conditions. The StarFabric interface ensures the modules perform seamlessly with no impact on the test system software.
-
Product
PCI-5114, 125 MHz Bandwidth, 2-Channel, 8-Bit PCI Oscilloscope Device, 256 MB
779745-03
Oscilloscope
125 MHz Bandwidth, 2-Channel, 8-Bit PCI Oscilloscope Device—The PCI‑5114 low-cost oscilloscope device has two channels that sample up to 250 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require flexible measurement configurations and up to 125 MHz of analog bandwidth.
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 3.5Ω To 773kΩ
50-298-143
Programmable Resistor Module
The 50-298-143 is a high density programmable resistor card with 3 channels which can be set between 3.5Ω and 773kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Mobile PCI Express Module with NVIDIA® Quadro® Embedded P5000
EGX-MXM-P5000
-
Meeting the needs of embedded, ruggedized, and mobile system builders, ADLINK's EGX-MXM-P5000 Embedded MXM GPU Modules utilizes Quadro Pascal architecture to deliver superior graphics and computing performance. The EGX-MXM-P5000 is specifically purposed to accommodate form factors incompatible with conventional PCI Express cards, and is built to maintain operations under a wide range of thermal and other environmental conditions. It’s the ideal choice for blade-based and other deployments where high GPU density is critical, with a choice of GPU memory capacity, extremely reasonable power requirements, and flexible display options.
-
Product
Flexible x1 PCI Express to PCI Adapter
SKU-041-0X
-
The Flexible x1 PCI Express to PCI Bus Adapter (Adapter) was designed to convert the x1 PCI Express bus into two 32-bit PCI buses. It allows you to connect up to two 32-bit PCI expansion boards to the motherboard x1/x4/x8/x16 PCI Express connector.The adapter includes a PCI adapter, x1 PCI Express host board and a PCI Express flat cable.
-
Product
7-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB111
-
The FAB111 has a PICMG 1.3 CPU card slot for the SHB (system host board) and offers one PCIe x16 slot, one PCIe x4 slots and four 32bit/33MHz PCI slots. Two high-speed USB 2.0 ports, a 24-pin ATX power connector and an 8-pin connector for thermal detected board are featured. The FAB110 is designed for the 8-slot industrial chassis, such as Axiomtek�s AX60551and AX60552.
-
Product
PCI 16 Reed Relay Output Digital Interface
8003
-
The 8003 PCI digital I/O interface provides 16 Reed relay outputs provide high quality, long-life, low current (10 Watt maximum), dry contact switch closures. Reed relays are well suited for low-current applications. The relays are normally open, and close when energized. Writing a 1 to the proper port bit can individually energize each relay.
-
Product
10-Slot X16 (16 Lane) Gen-3 PCI Express Expansion System
ExpressBox 3600-10
-
Magma’s ExpressBox 3600 provides optimal server grade GPU and other HPC peripheral expansion to existing host computer systems. Designed to support full Gen 3 x16 PCIe connectivity to all devices, the EB3600 supports 128 Gbps communication between the host and all peripherals. Ten total expansion slots are supported by the EB3600-10 for one or two hosts.
-
Product
PCI-5124, 150 MHz Bandwidth, 200 MS/s, 12-Bit PCI Oscilloscope Device
779171-01
Oscilloscope
150 MHz Bandwidth, 200 MS/s, 12-Bit PCI Oscilloscope Device—The PCI-5124 high-resolution oscilloscope device has two channels that sample up to 200 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for both time-domain and frequency-domain applications that require high-resolution measurements with up to 150 MHz of analog bandwidth.
-
Product
Squid PCI Express Carrier Board™ for M.2 and NGSFF (NF1) SSD Modules
-
Amfeltec Squid PCI Express Carrier Board™ for M.2 and NGSFF (NF1) SSD Modules
-
Product
Compact XMC-to-PCI Express (PCIe) Adapter
8241
-
Our Compact XMC-to-PCI Express (PCIe) Adapter 8X (Front-Panel I/O Only) (8241) permits use of a standard VITA 42.3 air-cooled XMC in the smallest possible edge finger PCIe form factor. The length of the adapter is the length of the XMC, while the height is a standard PCIe board, not the low-profile version.
-
Product
PCI, IEEE 488 GPIB Instrument Control Device for Linux
778686-01
GPIB Controller
The PCI‑GPIB is a plug‑and‑play IEEE 488 interface for PCs and workstations with PCI expansion slots. The PCI‑GPIB can sustain data transfer rates of more than 1.5 MB/s using the IEEE 488.1 three‑wire interlocked handshake. It also implements the high-speed IEEE 488.1 noninterlocked handshake (HS488) for benchmarked data transfers at more than 7.7 MB/s. The onboard bus master DMA controller means that there are no microprocessor interruptions in data transfer.
-
Product
XMC-to-PCI Express Adapter
4823
-
The Technobox, Inc. P/N 4823 XMC-to-PCI Express Adapter permits the use of a single-wide XMC module in a 1x PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector. The reserved future use, RFU, signals from P15 are available on one of the user connectors. The adapter also provides user access to all the signals on the XMC P16 connectors via two 64 pin headers UC1 and UC2.
-
Product
PCI 96 Channel TTL Digital Interface
8009
-
The 8009 digital I/O interface provides 96 channels of buffered drive digital I/O emulating 8255 mode zero, which can be utilized for PC based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems. 10K pull-up resistors are included. Optional values are available.
-
Product
PCI 32 Channel Reed Relay Output Digital Interface
8007
-
The 8007’s PCI digital I/O interface reed relay outputs provide high quality, long-life, low-current (10 Watt maximum), dry contact switch closures. Reed relays are well suited for low current applications. The relays are normally open, and close when energized.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for PCI With 2 Or 4 CAN Bus Nodes
ACP825-x
Simulator
ARINC825 (CAN bus) Test & Simulation module for PCI with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACP825-x PCI card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
Backplane Connectors
-
Offering a broad portfolio of backplane connectors that include SOSA aligned optical, COTS plus hard metric, VITA standard and high speed twinax interconnects. Our interconnect solutions address the requirements of mission-critical applications within commercial aerospace, space and defense market segments.
-
Product
XMC-to-PCI Express Adapter
4822
-
The Technobox, Inc. P/N 4822 XMC-to-PCI Express Adapter permits the use of a single-wide XMC module in a 4x PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector. The reserved future use, RFU, signals from P15 are available on one of the user connectors. The adapter also provides user access to all the signals on the XMC P16 connectors via two 64 pin headers UC1 and UC2.
-
Product
8 Channel ADC for PCI
PCI393
-
The PCI393 8-Channel Differential Input ADC for PCI is very well suited to be used in applications in which autonomous signal conversion is an issue, as well as in standard mid-range applications. Enabled channels are scanned at maximum rate and conversion results are stored in shared memory. A local DSP performs all functionality and user-specific functions can be added for customized operation.
-
Product
PCIe-5764, 16-Bit, 1 GS/s, 4-Channel PCI FlexRIO Digitizer Device
785961-01
FlexRio Digitizer
The PCIe-5764 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PCIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PCIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
PCIe-5774, 12-Bit, 6.4 GS/s, DC-Coupled, 2-Channel PCI FlexRIO Digitizer Device
785648-02
FlexRio Digitizer
The PCIe-5774 is a PCI FlexRIO Digitizer Device that provides up to 3.2 GHz of DC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5774 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The voltage ranges are software-selectable and include 200 mV peak-to-peak and 1 V peak-to-peak, with a selectable DC offset.
-
Product
MIL-STD-1553 One-Channel PCI Board
BRD1553PCI-1
-
The P-Orchestra™ is a one-channel MIL-STD-1553B PCI board, which includes Bus Controller (BC), Remote Terminal (RT) and Monitor (MT) capability. The board can be used as a hardware and software development kit for IP cores. P-Orchestra channels are software compatible to DDC® Enhanced Mini-ACE® components and architecture, with 16K word of internal RAM.
-
Product
Protocol Analyzer for PCI Express 5.0
Summit T54
Protocol Analyzer
The Summit T54 Protocol Analyzer captures, decodes and displays PCIe 5.0 protocol traffic data rates for x1, x2, x4 lane widths.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 4.09k Ohm - SPST
50-294-123
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
