PCI Backplanes
-
Product
Compact PCI Connector Board
cPCI-J2-SCSI
-
Ribbon cable is used between the rear IO and SCSI connector. The lengths are reasonably well matched. The cable is short. The design is intended for lower speed IO - 10 MHz and below. Above 10 Mhz there may be some attenuation.
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 2.5Ω To 472Ω
50-298-120
-
The 50-298-120 is a high density programmable resistor card with 4 channels which can be set between 2.5Ω and 472Ω with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 255 Ohm With SPDT
50-293-113
-
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 8.19k Ohm
50-294-024
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Digital I/O Boards
PISO-P32C32U
-
The PISO-P32C32/P32C32U/P32C32U-5V has 32 channels of optically isolated digital inputs and 32 channels of optically isolated digital outputs, arranged into four isolated banks. Each input channel uses a photo-coupler input which allows either internal isolated power supply or external power selected by jumper. Each digital output offers a Darlington transistor. The power supply of the input port may use the external power or the power from the PC side via DC/DC converter. The power supply of the output port should use the external power. The board eliminates ground-loop problems and isolates the host computer from damaging voltages.
-
Product
PCI To PCI Express Board
MS 1718
-
PCI to PCI Express card is used to extend PCI / PCI-X bus from one PCI system to another system over an optical fiber medium up to 500meters or over a copper medium up to 7 meters using a PCI express interface. This card receives/transmit PCI signals from/to the Host System. These PCI signals are converted into PCI Express using PCI / PCI-x to PCI Express cross bridge and vice versa. The PCI Express signal is transmitted / received through the optical interface or copper interface.
-
Product
Intel® Core™ I Automation Computer With 4 PCI(E) Expansion Slots
UNO-3285G
-
Intel® 6th Gen Core™ i7-6822EQ Quad Core Processors with 8GB DDR4 Memory2 x GbE, 6 x USB 3.0, 2 x RS-232/422/485, 2 x RS-232 (pin header), 1 x DVI-I, 1 x HDMI2 x PCIe x8, 2 x PCI, 2 x mPCIe (2 x full), 1x CFast, slot, 1 x mSATA slot (optional)Dual Hot-Swappable storage with thumb screw support for RAID 0/1Supports Fieldbus Protocol by iDoor TechnologyDual power input for power redundancyFront LED indicator design for monitoring system status
-
Product
PCI Altera 485/LVDS - Altera User Design
-
The PCI compatible PCI-Altera-485/LVDS design is for the advanced user who wants to implement their own Altera design or requires reconfigurable logic. The PCI-Altera-485/LVDS makes the implementation and use of the 20K400E easy. Larger Altera parts are available. The design comes with the basic features built in and the specific features ready for you.
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 3Ω To 6.97kΩ
50-298-130
-
The 50-298-130 is a high density programmable resistor card with 4 channels which can be set between 3Ω and 6.97kΩ with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI-5105, 8‐Channel, 12-Bit, 60 MHz Bandwidth PCI Oscilloscope Device
779686-03
-
8‐Channel, 12-Bit, 60 MHz Bandwidth PCI Oscilloscope Device—The PCI‑5105 high-density oscilloscope device has eight simultaneously-sampled channels with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with many channels that require up to 60 MS/s or 60 MHz of analog bandwidth.
-
Product
PCI
-
PCI is a local computer bus for attaching hardware devices in a computer. PCI (Peripheral Component Interconnect) is part of the PCI Local Bus standard. The PCI bus supports the functions found on a processor bus but in a standardized format that is independent of any particular processor’s native bus.
-
Product
IRIG Time Code Receiver for Computers (PCI Express)
TCR180PEX-EL
-
Meinberg Funkuhren GmbH & Co. KG
The TCR180PEX-EL receives IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes and can be used for synchronizing the system time of its host PC. The IRIG output of this card can generate an IRIG signal for other IRIG time code readers. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements).
-
Product
PCI card with 3 IP sites
PCI3IP
-
The PCI compatible PCI3IP design adds 3 Industrypack compatible slots to your PCI host. The PCI3IP acts as an adapter, converter, carrier, or bridge between the PCI bus and your IndustryPack hardware. The PCI3IP is a half size PCI card with 3 IP sites; compatible with the smallest chassis and the tallest processors that prevent full size solutions.
-
Product
PCI-5152, 300 MHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device
779945-01
-
300 MHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device—The PCI‑5152 high-speed oscilloscope device has two channels that sample up to 2 GS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 300 MHz of analog bandwidth and flexible measurement configurations.
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 4Ω To 22.3MΩ
50-298-154
-
The 50-298-154 is a high density programmable resistor card with 3 channels which can be set between 4Ω and 22.3MΩ with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
4-CH 16-Bit 80 MS/s PCI Express Digitizer
PCIe-9834
-
ADLINK's new PCIe-9834 high-speed PCI Express digitizer, featuring four simultaneously sampled 80 MS/s input channels with 16-bit resolution, 40 MHz bandwidth, and up to 1 GB DDR3 onboard memory. Each of the four input channels supports up to 80MS/s sampling, with 16-bit resolution A/D converter. This allows simultaneous recording of signals on all channels with no interchannel phase delay. The extremely large onboard memory enables long recording times even at the highest sampling rates. Each connection pair (lane) can achieve burst connection speeds of 250MB/s. The PCIe-9834, based on x4 lane slot PCI Express technology, provides a clear advantage in that direct connection of each slot allows full transfer bandwidth for each individual card.
-
Product
Low Profile PCI 24 Channel TTL Digital Interface
8018
-
The 8018 Low Profile PCI digital I/O interface provides 24 channels of buffered drive digital I/O emulating 8255 mode zero. The board can be utilized for PC-based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems.
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 2.5Ω to 925Ω
50-298-021
-
The 50-298-021 is a high density programmable resistor card with 9 channels which can be set between 2.5Ω and 925Ω with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PCI Digital I/O Boards
PCI-822LU
-
Universal PCI, 250 kS/s, 32/16-ch 12-bit Analog Input, 2-ch 16-bit Analog Output with 32-ch Programmable DIO. Replacement for A-823PGH Series, A-823PGL Series, A-822PGH Series, A-822PGL Series, A-821PGH Series, & A-821PGL Series.
-
Product
PCIe and PCI Avionics Interface Cards
-
Ballard PCI Express (PCIe) and PCI Avionics Interface Cards enable computers to interface with a variety of avionics databuses for testing, validating and simulating commercial and military avionics equipment and systems.
-
Product
PCI to Star Fabric Module
51-921-001
-
This module resides in the Slot 1 position of a PXI chassis and interfaces to the backplane of the PXI chassis. When located in a generic peripheral slot, it can be used to drive two extension PXI chassis.
-
Product
PCI Express To PCI Express Expansion With 7 PCIe X8 Gen-2 Slots
ExpressBox 2400
-
Accommodating (7) full-length, full-height PCIe cards, while only being 4U and 8.5 ”wide, the EB2400 is the perfect chassis for small space applications, where size is a top priority.
-
Product
PCIe-8398, x16 Gen3, PCI Express Host, 13.6 GB/s Device for PXI Remote Control
784179-01
-
The PCIe-8398 is a host interface card used to control a PXI Express chassis over a software-transparent PCI Express Gen 3 x16 link. The PCIe-8398 is installed into a x16 PCI Express slot of a desktop or rackmount PC and is connected to a PXIe-8398 or PXIe-8399 PXI remote control module using Gen 3 x8 copper cables.
-
Product
PCI Analog IO Board
MS 1803
-
*Bus Interface:- PCI Bus*Analog Inputs:- 16 Single Ended Inputs / 8 Differential Ended Inputs*Input Resolution:- 16 Bits*Input Range:- ±10V*Gain:- Programmable Gain Control (1, 2, 4, 8, 16)*Sampling Rate up to 100Ks/S*Peak Measurement +ve and -ve peak for all input channels
-
Product
PCI-5122, 100 MHz Bandwidth, 100 MS/s, 14-Bit PCI Oscilloscope Device
778758-01
-
100 MHz Bandwidth, 100 MS/s, 14-Bit PCI Oscilloscope Device—The PCI‑5122 high-resolution oscilloscope device has two channels with greater than 75 dBc spurious‑free dynamic range (SFDR) and flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for both time-domain and frequency-domain applications that require high-resolution, low-noise measurements with up to 100 MS/s and 100 MHz of analog bandwidth.
-
Product
LVDT I/O Cards XMC PCI
-
Computer Conversions Corporation
The Computer Conversions Corporation XMC Series Cards can be used in a wide variety of test, data acquisition, simulation, and control applications.
-
Product
4-Port PCI Express USB Vision Frame Grabber
PCIE-1154-BE
-
Half-Size PCI Express Board Gen 2.0 x4 delivering 2.0 GB/s total bandwidthHost Controller – Renesas μPD720202Supports four USB 3.0LED indicator for each portSupports 900-mA max. current per portSupports cable-lock mechanism for reliable cable connectionSupports Microsoft Windows 7/8.1/10 and Linux
-
Product
PCI High Density Potentiometer Card 3-Channel, 24-Bit, 0 To 16M Ohm
50-296A-121-3/24
-
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
96-CH 12-Bit 3 MS/s High-Density Analog Input PCI Express Card
DAQe-2208
-
ADLINK DAQe-2208 is an high-density and high-performance analog input card. The device can sample up to 96 AI channels with different gain settings and scan sequences. It makes them ideal for dealing with high-density analog signals with various input ranges and sampling speeds. These devices also offer differential mode for 48 AI channels in order to achieve maximum noise elimination.
-
Product
PCI Multifunction Board
PCI-1002/H/L
-
The PCI-1002 series is a family of A/D boards for PCs with a PCI bus. It features 110KHz data acquisition under DOS and Windows. The PCI-1202H/1202L provides 32 single-ended or 16 differential inputs, 16 digital input and digital output channels. The -H means high gain model and the -L means low gain model. The PCI-1202 series provides three flexible external trigger modes: pre-trigger, post-trigger and external pacer trigger.
