PCI Backplanes
-
product
PCIe-8431, PCI Express, 2-Port, RS485/RS422 Serial Interface Device
782124-01
The PCIe‑8431/2 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between … 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 131k Ohm
50-294-034
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI High Density Screened MUX 10 Ch 8 Pole
50-670-021-S-10/8
The 50-670 series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
4-CH 12-Bit 80 MS/s PCI Express Digitizer
PCIe-9814
The ADLINK PCIe-9814 is a PCI Express digitizer providing speedy, high quality data acquisition. Each of the four input channels supports up to 80MS/s sampling, with 12-bit resolution A/D converter. This allows simultaneous recording of signals on all channels with no inter channel phase delay. The extremely large on-board memory enables long recording times even at the highest sampling rates.Unlike parallel PCI buses, PCI Express slots utilize serial point-to-point connection. Each connection pair (lane) can achieve burst connection speeds of 250MB/s. The PCIe-9814, based on x4 lane slot PCI Express technology, provides a clear advantage in that direct connection of each slot allows full transfer bandwidth for each individual card. The ADLINK PCIe-9814 x4 digitizer can be used in any standard PCI Express slot, x4, x8, or x16.
-
product
PCI 32x4 2Amp High Density Matrix Card
50-528-001
The 50-527, 50-528 and 50-529 are a range of PCI single pole matrix cards supporting either 64 or 128 crosspoints using electro-mechanical relays. They are capable of switching voltages up to 300VDC/250VAC and current up to 2A.
-
product
PCI High Density Pecision Resistor Card, 9-Channel, 2Ω To 122Ω
50-298-112
The 50-298-112 is a high density programmable resistor card with 9 channels which can be set between 2Ω and 122Ω with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCIe-8430, PCI Express, 2-Port, RS232 Serial Interface Device
782122-01
The PCIe‑8430/2 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard … COM ports for compatibility with programs that use serial communications.
-
product
13-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB113
*Designed for PICMG 1.3 SBC*Compatible with the AX61400, AX6145, and AX6156LE chassis*Supports one PICMG 1.3 CPU card slot, seven PCIe x1 slot, one PCIe x16 slot, and four 32bit/33MHz PCI slots
-
product
PCI Bus Analog Output Board, 4 Isolated Outputs, 14 Bit
APCI-3501-4
4 analog output channels Optical isolation 500 V Settling time 30 µs typ. 14-bit resolution (13 bit for 0-10 V) Output voltage: ±10 V, 0-10 V (switchable through software) Output voltage after reset: 0 V Each output channel has its own ground line (without optical isolation from the others) Driver capacity: 5 mA/500 pF Short-circuit protection, EMI filters Noise neutralization of the PC supply Creeping distance: 3.2 mm acc. to DIN VDE 0411-100 Watchdog for resetting the analog output channels (4 different time units: µs, ms, s, min) or as 12-bit timer (with interrupt possibility), when the watchdog function is not necessary2 digital input channels, 24 V, isolated 2 digital output channels, 24 V, isolated Noise immunity Test level: ESD: 4 kV Fields: 10 V/m Burst: 4 kV Cond. radio interferences: 10 V
-
product
20-slot ATX-supported Bridged PICMG Bus Active Backplane
ATX6022/20GP18
*1 PICMG, 18 PCI and 1 ISA*Compatible with AX61492 chassis*Supports both AT and ATX power supply
-
product
ARINC 429 Test & Simulation Interface for PCI Express
PCIe-C429
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
PCI Bus Analog Output Board, 8 Isolated Outputs, 14 Bit, Custom Version
APCI-3501-8-2P
*"-2P" indicates custom version*8 analog output channels, 14-bit*Optical isolation 500 V*4 digital Input*4 digital output*24 V, optically isolated*Watchdog
-
product
24-lane, 24-port, PCI Express
PEX89024
The new PCIe Gen 5.0 (32 GT/s) PEX89000 series builds on the longevity of the Broadcom series of switches, now spanning 13 families. The PEX89000 family allows customers to build systems from simple PCIe connectivity inside the box to high-performance, low-latency, scalable, cost-effective PCIe fabrics for composable hyper-scale compute systems supporting ML/AI and Server/Storage applications.
-
product
PCI Module
PCI-6713B-4IP
The PCI-6713B-4IP module provides a high performance flexible I/O scheme, thatsupports industry standard Industry Packs™. For application requiring low cost,high density I/O or unique combinations, the 6713B-4IP is the ideal solution. The local 6713B DSP can be used to simply move data to and from the PCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc. Custom application software can be downloaded to the DSP via the PCI bus. A very low cost, non-intelligent version is also available, PCI-SIP.
-
product
PCI Express Digital I/O Cards With Counters And COS Detection
PCIe-DIO-24DCS, PCIe-DIO-24DC, PCIe-DIO-24DS, and PCIe-DIO-24D,
This product is a x1 lane PCIe DIO board available in four models ranging from basic DIO to advanced COS detection and Counter/Timer capabilities. The card emulates an 8255 compatible chip, providing 24 DIO lines. The DIO lines are grouped into three 8-bit ports: A, B, and C. Each 8-bit port is configured via software to function as either inputs or outputs. Port C can be further broken into two 4-bit nybbles via software and configured as either inputs or outputs.
-
product
16 SE Or 8 Diff. Input Channels, 8 Analog Output Channels, PCI Express
APCIE-3121-16-8
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
PCI Module
PCI-4SIP
The PCI-4SIP Module provides a Full PCI performance flexible I/O scheme, that supports industry standard Industry Packs. Choose from over a 100 different Industry Packs from Alphi Tech and others. For application requiring low cost, highdensity I/O or unique combinations, the PCI-4SIP is the perfect solution.
-
product
PCI High Density Resistor Card 5-Channel, 12-Bit, 0 To 4k Ohm
50-295A-021-5/12
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Compact PCI Express (3U) Generic Carrier Card
ACCx-1
To complement the wide range of interface modules for dedicated Avionics Databuses and Networks, AIM offers a range of Carrier modules for the use of AIM or any 3rd Party PMC and XMC module on various backplanes.
-
product
PCI Extender Card for cPCI Systems
DP-cPCI-7497
The DP-cPCI-7497 is highly flexible PCI Extender card, which can be used to extend PCI / PCI-X bus from one system to another system over an optical fiber medium upto 500m distance. A PCI-X to PCI-e Bridge is used to convert the PCI / PCI-X protocol to x4 PCI Express protocol operating at 2.5Gbps.The PCI-X to PCI-e Bridge is connected to four optical transceivers (x4 PCI- e link) which can transmit optical signals upto 2.5Gbps speed.A x4 copper medium connection option in lieu of optical transceivers is also available.
-
product
PCI Express Waveform Digitizer
ATS9626
ATS9626 is a 250 MS/s 16 bit PCI Express waveform digitizer with an on-board, user-programmable FPGA. With fixed dc-coupled input range of +/- 1.25V and signal to noise ratio in excess of 72 dB, ATS9625 is an ideal solution for applications that require high dynamic range with dc coupling.
-
product
PCI Resistor Card 4-Channel 1 Ohm To 510 Ohm With SPDT
50-293-114
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI Resistor Card 2-Channel 2 Ohm To 65.5k Ohm With SPDT
50-293-133
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI Single 22 X 8 Matrix 1 Pole Screened
50-512-021-S
The 50-510 series of matrix cards feature a wide range of selectable switching configurations (22x4,dual 20x4,22x8 and 44x4). Larger matrices may be constructed by Daisy Chaining the common signals from multiple PCI cards. For example four 44x4 Cards will form a 176x4 Matrix, a total of 704 crosspoints. Expansion cables are available for the 50-512 and 50-513: The 50-512 can be expanded to 44x8 or the 50-513 can be expanded to 88x4 using two cards linked by the ribbon cable assembly 50-976-020-0.1M. Also the 50-512 can be expanded to 22x16 or the 50-513 can be expanded to 44x8 using two cards linked by the ribbon cable assembly 50-976-050-0.1M.
-
product
64-CH 12/16-Bit Up to 3 MS/s Multi-Function DAQ PCI Express Cards
DAQe-2200 Series
ADLINK DAQe-2200 series are highdensity and high-performance multi-function DAQ PCI Express cards. The devices can sample up to 64 AI channels with different gain settings and scan sequences. It makes them ideal for dealing with high-density analog signals with various input ranges and sampling speeds. These devices also offer differential mode for 32 AI channels in order to achieve maximum noise elimination.
-
product
2-slot Fanless Industrial System With Intel® Celeron® Processor J1900, Front-access I/O, PCIe And PCI Slots
IPC922-215-FL
The IPC922-215-FL is an energy-efficient fanless 2-slot industrial system with rugged mechanism and optimized expandability. The extreme compact IP30-rated IPC922-215-FL utilizes an onboard Intel® Celeron® quad core processor J1900 2.42GHz with one DDR3L 1333 up to 8 GB memory. To fulfill difference application needs, the rugged Intel® Bay Trail SoC barebone embedded system provides great expansion capability with two flexible PCI/PCIe slots that can be customized. Additionally, the Axiomtek IPC922-215-FL can withstand temperatures ranging from -10°C to 50°C, and is equipped with a wide range 10 ~ 30 VDC power input for industrial application.
-
product
PCI Synthesizer
SYNTH300 Series
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
product
ARINC 429 Multichannel Interface Card for Mini PCI Systems
DAS-429mPCI/RTx
The DAS-429mPCI/RTx is an ARINC 429, multichannel interface card for Mini PCI systems. The card’s small size and suitability for Mini PCI notebook computers, make them a complete solution for developing and testing ARINC 429 interfaces and for performing system simulation of the ARINC-429 bus, both in the lab and in the field.The DAS-429mPCI/RTx is supplied with C drivers, including source code and Mystic application program.
-
product
Flexible x1 PCI Express Riser
SKU-039-XX
The Flexible x1 PCI Express Riser (Riser) was designed to extend the x1 PCI Express bus. The Riser includes an x1 PCI Express adapter board (optional: x4 PCI Express adapter), x1 PCI Express host board and a 12” PCI Express Flat cable.
-
product
PCI Precision Resistor Card 9-Channel, 2Ω To 26.7kΩ
50-297-032
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.





























