-
Product
Capacitive Touch Controllers
TouchXpress
-
Silicon Labs' TouchXpress devices are highly optimized solutions that enable designers to easily design and integrate capacitive sensing into applications. These devices quickly replace mechanical buttons and switches with modern capacitive touch buttons by eliminating the firmware complexity and reducing development time.
-
Product
Level Indicators
-
4B has a wide range of radio frequency (RF), rotary paddle and capacitance point level indicators for detecting high, intermediate, or low levels of liquids, powders and free flowing granular solids stored in tanks, bins, silos or other containers. Certain units can also be used as plug or choke detectors in chutes, conveyors and elevator legs.
-
Product
8 GHz, 20 GS/s, 4ch, 100 Mpts/Ch High Definition Oscilloscope
WavePro 804HD
Oscilloscope
HD4096 technology provides 12-bit resolution up to 8 GHz and 20 GS/s. Up to 5 Gpts of acquisition memory enables detailed viewing of long events. 15.6" 1900 x 1080 Full HD capacitive touchscreen. New ProBus2 input supports up to 8 GHz bandwidth and direct compatibility with a wide variety of existing ProBus probes - 50Ω and 1MΩ coupling modes support all input types on a single connector. MAUI with OneTouch user interface for intuitive and efficient operation.Deep toolbox enables and simplifies complex analysis.Intuitive navigation to quickly find important features in long waveforms.Zone Trigger – Simple Triggering for Complex Signals.
-
Product
Low-Side FET Drivers
-
Renesas' low-side FET drivers are very high-speed matched dual-drivers capable of delivering peak currents into highly capacitive loads and are excellent at driving large capacitive loads with minimal delay and switching times.
-
Product
NI TB-2642B Terminal Block for NI 2532B as 1-Wire 16x32 Matrix Topology Without Column Protection Resistors
782385-05
Terminal Block
The TB-2642B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 8x64 matrix. You can directly connect the TB-2642B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2642B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Infiniium S-Series High-Definition Oscilloscope: 2.5 GHz, 4 Analog Plus 16 Digital Channels
MSOS254A
Oscilloscope
2.5 GHz bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 7.4 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15" capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
Product
TD Guard
-
TD Guard Intelligent Sensor is an on-line CONTINUOUS Capacitance and tan-δ monitoring system for transformer bushings. TD Guard Intelligent Sensor is the first and only instrument on the market providing absolute Tan-δ measurement in on-line permanent monitoring of transformer bushings, granting the best level of diagnostic leverage and reliability. Sensitivity better than 10-4.
-
Product
ESD Testers
-
Hanwa Electronic Ind. Co.,Ltd.
◆Adaptable to the following international standard waveform;JEDEC, ESDA, AEC, and JEITA◆This system’s uniquely short discharge circuit is made possible by its original mechanical design.◆The short circuit minimizes the influence of inductance and capacitance on the data.◆The use of a single circuit ensures data stability for each device pin tested.
-
Product
WaveRunner Oscilloscope, 4 GHz Bandwidth, 4 Input Channels, 40 GS/s on 2 Ch Sample Rate
WaveRunner 9404M
Oscilloscope
4 GHz, 40 GS/s, 4ch, 64 Mpts/Ch DSO with 15.4" Capacitive Display.
-
Product
Oscilloscope - 350 MHz, 2 Analog Channels
DSOX3032T
Oscilloscope
350 MHz2 analog channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
LCR Meter
M162
-
M162 LCR meter is a great complimentary tool to most multi-meters. Regular multi-meters are good in many way. But they usually have rather limited or even no ability for capacitance, inductance, and sub-ohm resistance measurement. The addition of a M162 LCR meter will overcome this deficiency. The DIY kit version of M162 is very easy to build. No special calibration is required to achieve ~1% accuracy.
-
Product
DIGITAL MULTIMETER, Compact 3 1/2
IBL-603
-
International Biological Laboratories
Interlabs 603 is a compact, rugged, battery operated, handheld 31/2 Digital Multimeter with large LCD display. They can be used for measuring DC voltage and current, AC voltage and current, resistance diode forward voltage, transistor hFE and open circuit testing with capacitance test facility etc.
-
Product
Portable 2 Channel/4 Channel FFT Analyzer
CF-9200/9400
-
The CF-9200 and CF-9400 are an all-in-one portable FFT analyzer. All FFT analysis operations can be performed with the integrated hard keys and capacitance type touch panel without requiring an external PC for analysis. The new, exclusively developed 100kHz high-performance analysis front-end system incorporating a 24-bit A/D converter enables easier and more reliable analysis of noise and vibration generated by plant lines, pumps, motors, automobiles, railway vehicles, home electrical appliances and devices, and electrical and electronic parts than previous models. The CF-9200 and CF-9400 also offer solutions for field workers in their FFT analysis, including the resonance and frequency characteristics of mechanical structures in a vibrating environment with electromagnetic vibrators and impulse hammers.
-
Product
Materials Lab XM
-
The Materials Lab XM product provides a fully integrated reference grade time domain and AC measurement platform. No need to switch sample connections between techniques. Time domain measurements include I-V (current voltage) characterization as well as fast pulse techniques. AC testing techniques include everything from single-sine analysis, to multisine / Fast Fourier Transform for faster low frequency analysis, to harmonics and intermodulation for testing linearity and breakdown of materials. Measurements of electrical impedance spectroscopy (EIS), admittance, permittivity and capacitance are all provided from the XM-studio MTS software platform, together with integrated equivalent circuit analysis functionality.
-
Product
AstroAI Digital Multimeter
TRMS 6000
-
WIDE RANGE of tests for Voltage, Current, Resistance, Continuity, Capacitance, Frequency; Tests Diodes Transistors, TemperaturePROFESSIONAL LEVEL features include Auto-Ranging capability, and True RMS for measuring both AC Current and Voltage
-
Product
Pocket Size Digital Multimeter, Resistance Measure, 3999 Count, Average, Auto Range, 3.75 Digit
72-10395
-
Pocket sized multimeter which comes in a self-contained folding case. The meter measures AC/DC voltage, resistance, capacitance & frequency.
-
Product
Adhesion Tester
Surf-2
-
Rtec Adhesion Tester is a turn key solution to measure Pull up Adhesion force, Work of Adhesion and Shear Adhesion of materials. Equipped with Ultra-Sensitive Capacitance Load Cells this tester provides µN level resolution with forces up to 5N. The High-Resolution sensors allow characterization of large samples over macroscopic length scales to study the effect of texture and other surface modifications. Integrated with High Resolution Inverted Camera, it allows the researchers to measure Contact Area vs. Force making it extremely useful in measuring Adhesion of Soft Materials, Biomimetics and Hydrogels.
-
-
Product
Mixed Signal Oscilloscope 500 MHz, 2 Analog Plus 16 Digital Channels
MSOX3052G
Oscilloscope
The MSOX3052G 500 MHz oscilloscope provides 2 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
7" Capacitive Touch Panel Overlay
-
The LattePanda 7-inch touch panel overlay uses capacitive touch technology and multi-touch to bring you a truly interactive experience. Simply overlay the panel on your LattePanda 7-inch display, power the board, and you will have a high-quality user interface that you can use to create all-in-one, integrated projects.
-
Product
Oscilloscope - 1-6 GHz, 2 Analog Channels
DSOX6002A
Oscilloscope
1 GHz - 6 GHz2 analog channels Easily view and isolate signals on the 12.1-in capacitive multi-touch screen with Zone triggering and 450,000 wfms/s update rate Make more precise measurements with 115 Vrms noise floor at 1 mV/div (1 GHz)Get performance measurements anywhere with the portable 6-in deep size Quickly see analysis details with standard histogram and color grade View signal integrity with jitter and eye diagram analysis options
-
Product
WaveRunner Oscilloscope, 500 MHz Bandwidth, 4 Input Channels, 20 GS/s on 2 Ch Sample Rate
WaveRunner 9054
Oscilloscope
500 MHz, 20 GS/s, 4ch, 16 Mpts/Ch DSO with 15.4" Capacitive Display.
-
Product
RF Spectrum Analyzer
FSA-100
-
ShinewayTech® FSA-100 series 6GHz spectrum analyzer are widely used in 2G/3G/4G/5G etc. FSA-100 series have the industry's rare high receiver sensitivity performance with a minimum display average noise level of -165dBm/Hz. Power measurement dynamic range up to 100dB, maximum RF input power exceeds 27dBm. FSA-100 series are equipped with a 7" ultra-large capacitive touch screen (resolution 1024*600). Excellent user experience.
-
Product
Capacitive Sensors
-
Our separate sensor amplifiers allow an easy adjustment and interpretation of our capacitive sensor heads. For this purpose, both a compact comfort-amplifier and an IO-Link-amplifier for top hat rail mounting are available.
-
Product
Mixed Signal Oscilloscope 1 GHz, 4 Analog Plus 16 Digital Channels
MSOX3104G
Oscilloscope
The MSOX3104G 1 GHz oscilloscope provides 4 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
DC Electronic Load
Model - KM-mPD-501
-
Kusam Electrical Industries Limited
KM-mPD-501 DC electronic load mainly focuses on the testing of power circuit on PCB. KM-mPD-501 offers a solution for function test of Switch step up, Stepdown, Regulators and Driver IC . Engineer puts components, such as CPU, DSP, FPGA; etc on a PCB after the power circuit has been tested. It’s not complete to use a meter to measure the voltage. KM-mPD-501 offers engineer OVP, OCP and OPP functions that help engineer know the value of overload current . On the other hand, engineer can use a programmable DC power supply (mPP series) to offer external power and connect PCB’s output to KM-mPD-501. Then engineer can easily get output watt, figure out the efficiency of power circuit and check if inductances, capacitances and resistances perfectly work with the power circuit. KM-mPD-501 not only offers loading emulation of current but also provides OVP and OPP. User can use these functions to test solar power battery, rechargeable battery and motor driver. In school laboratory, KM-mPD-501 helps students do experiment on power circuit, linear circuit and driver circuit.
-
Product
Handheld Moisture Meters
-
Since water has a dielectric constant considerable higher than any other material, even a small amount of water in a product will cause the combination dielectric constant to increase substantially. Finna Sensors' capacitance meters can easily recognize this increase in water content and are programmed to display the result in direct reading percent moisture content.
-
Product
Portable Dew point Analyzer
GEN-25
-
Shanghai ChangAi Electronic Science & Technology Co.,Ltd
GEN-25 dew point analyzer is a kind high-performance intelligent moisture tester, which is developed by film capacitive ceramic dew point sensor combine with latest micro computer technology. It is used to measure the moisture content in various gases.
-
Product
Transformer Turns Ratio Testers
-
Transformer turns ratio testers from TRT series are DV Power instruments mainly designed for the measurement of power transformer turns ratio. Also, they measure transformer excitation current and phase shift. Special tests, such as automatic vector group detection and magnetic balance, can be performed on three-phase transformers and three-phase autotransformers.All models, except TRT03 series, have a built-in true three-phase power source, which is necessary for testing turns ratio of transformers with special configurations, such as phase-shifting, rectifier, arc-furnace, traction transformers, etc.DV Power turns ratio testers can output various test voltages for different applications. From the extremely low test voltage of 1 V AC that enables turns ratio verification of the majority of current transformers, up to the highest test voltage of 500 V AC that provides the most accurate turns ratio testing of power transformers used in power generation and transmission. By using the external booster, test voltage increases up to 5 kV AC in order to successfully test capacitive voltage transformers.All DV Power turns ratio testers have a built-in tap changer control unit. Because of that, it is possible to control the on-load tap changer (OLTC) directly from the device. In order to make the most out of this feature, the instrument and included DV-Win software can be programmed to do everything automatically – running turns ratio tests, changing OLTC tap positions, and saving results. This option significantly facilitates and shortens the turns ratio testing time.TRT turns ratio testers use the same set of cables as three-phase winding ohmmeter & tap changer analyzers from the TWA series. Consequently, it enables one-time cable setup for performing eight tests:turns ratioexcitation currentphase anglemagnetic balancevector group detectionwinding resistanceon-load tap changer DVtestand demagnetization.
-
Product
VLF Diagnostics System
PHG 70 TD
-
Cable testing and diagnostics with the BAUR PHG 70 TD. The combination of the PHG 70 programmable test generator with the BAUR dissipation factor measurement system produces the cable testing and diagnostics system PHG TD. It is operated via PC control. Dissipation factor measurement and diagnostic testing sequences can be programmed in the menu, after which the dissipation factor measured values are automatically determined in various voltage steps and a final evaluation is conducted.* Biggest dynamic range of tan delta measured values from 1 to 10-4 with a cable capacitance >10 nF to 20 uF* High resolution +/- 1x10-5 applicable even in new PE/XLPE cables* Insensitive against interferences due to complete mains separation* Lowest time required for assessing a medium-voltage cable (3-phase approx. 1 hour)
