Power Calibrators
Verify power measuring instruments accuracy.
-
Product
4-In-1 OSLT Mechanical Calibration Kit, DC To 18 GHz, Type-N (f) 50 Ohm
85519A
Mechanical Calibration Kit
Easily calibrate non-insertable devices with this module combining an open, short, load, and through in a compact unit
-
Product
PXI Programmable Power Supply, 0-48VDC
41-743-001
Programmable Power Supply
The 41-743 is a fully isolated programmable power supply capable of delivering output voltages to 48V with a voltage setting resolution of less than 1mV. The output is capable of delivering up to 40W to the user load and requires no external power supply – power is drawn from two PXI backplane slots.
-
Product
10 MHz – 18 GHz USB Power Sensor
U2000B
Power Sensor
U2000B USB Power Sensor measures average power over the frequency range 10 MHz to 18 GHz and power range -30 dBm to +44 dBm.
-
Product
Power Device Analyzer / Curve Tracer
B1505A
DC Power Analyzer
The Keysight B1505A Power Device Analyzer / Curve Tracer is the only single box solution available with the capability to characterize high power devices from the sub-picoamp level up to 10 kV and 1500 A. These capabilities allow evaluation of novel new device such as IGBT and materials such as GaN and SiC. The B1505A supports a variety of modules: high voltage SMU (HVSMU), high current SMU (HCSMU), ultra high current (UHC) module, ultra high voltage (UHV) module and high voltage medium current (HVMC) module. The B1505A also supports: high-power SMU (1 A/200 V), medium-power SMU (100 mA/100 V) ,medium-current SMU (1 A/30V pulsed, 100 mA/30V DC) and a multi-frequency capacitance measurement unit (1 kHz 5 MHz). Its ten-slot modular mainframe allows you to configure the B1505A to suit your measurement needs.
-
Product
Power, Patchcord, ITA, 72", Micro Power, 14 AWG White, Single Ended ( 22 Amps)
7-251914000-072
Power Patchcord
Power, Patchcord, ITA, 72", Micro Power, 14 AWG White, Single Ended ( 22 Amps).
-
Product
Programmable Linear DC Power Supply, 1 Output, 0-16V/0-8A
T3PS16081P
DC Power Supply
Programmable Linear DC Power Supply, 1 Output, 0-16V/0-8A.
-
Product
200W Power Supply, 8V, 20A or 20V, 10A
E3633A
Power Supply
Keysight basic DC power supplies offer essential features for a tight budget. The single output, 120-200 W, GPIB, E3632A-E3634A provide dual range outputs; small, compact size for bench use; low output ripple and noise; as well as built-in measurements and basic programmable features with GPIB and RS232 interface. The Keysight 200W, GPIB, single output E3633A is a high performance supply optimized for manual and basic automated testing; and, with a combination of benchtop capabilities and system features, it is designed to help improve measurement quality and reduce test time.
-
Product
Programmable High Precision DC Power Supply 1 Output 0-100V, 0-1A, 100W
T3PS100011P
DC Power Supply
Programmable High Precision DC Power Supply 1 Output 0-100V, 0-1A, 100W.
-
Product
PXIe-4154, 2-Channel, 8 V, 3 A PXI Programmable Power Supply
781155-01
Programmable Power Supply
2-Channel, 8 V, ±3 A PXI Programmable Power Supply—The PXIe‑4154 is a specialized programmable power supply for battery simulation. It is designed to simulate a lithium‑ion battery cell’s transient speed, output resistance, and 2‑quadrant operation (source/sink). Critical to many RF and wireless applications, the simulator’s fast transient response time allows it to rapidly respond to changes in load current with minimal voltage dip, which makes the PXIe‑4154 ideal for powering devices under test (DUTs) such as RF power amplifiers, cellular handsets, and a variety of other mobile devices. To model the behavior of a battery more accurately, you can use the onboard programmable output resistance to simulate a battery’s internal resistance. For quiescent and standby current measurements, the PXIe‑4154 features integrated current measurement.
-
Product
Power, Patchcord, ITA, 72", Micro Power, 12 AWG White, Single Ended (22 Amps)
7-251912000-072
Power Patchcord
Power, Patchcord, ITA, 72", Micro Power, 12 AWG White, Single Ended (22 Amps).
-
Product
Power Module, 100V, 3A, 300W
N6776A
Power Module
The Keysight N6776A is a 300 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
Product
E-Series Average Power Sensor
E9301H
Power Sensor
Measure the average power of all modulation formats Wide dynamic range power measurements from -50 dBm to +30 dBm10 MHz to 6 GHz frequency coverage for Wireless Comms formatsLow SWR for reducing mismatch uncertainty Calibration factors, linearity and temperature compensation data stored in EEPROM Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
Product
Autoranging System DC Power Supply, 500 V, 60 A, 10000 W, 400 VAC
N8948A
DC Power Supply
The Keysight N8900 Series is a family of 5 kW, 10 kW, and 15 kW autoranging, single-output power supplies available in 14 different voltage, current, and power combinations and either 208 VAC or 400 VAC (28 total models).
-
Product
200W Autoranging Power Supply, 60V, 10A
E36232A
Power Supply
E36232A provides more useable power with autoranging architecture in a bench friendly design with full programmability; LAN, USB and optional GPIB interface.
-
Product
500 Watt AC/DC Power Line Conditioner, 3U VPX, Holdup Time
VPX56-3HU
Power Line Conditioner
NAI's VPX56-3HU is a rugged, high-performance 500-Watt Output +28 VDC Input 3U VPX AC/DC Power Line Conditioner designed for aerospace, defense, and industrial markets. This off-the-shelf power supply plugs directly into a standard VPX conduction cooled chassis and protects downstream DC-DC converters from MIL-STD-704 transients, low-voltage conditions and power interruptions, providing up to 50 milliseconds of holdup time at up to 500-Watts. Continuous Background Built-In-Test (BIT) and I2C communication are included.
-
Product
High Power, Contact, ITA, 150 Amps, 2 AWG
610150101
Power Contact (ITA)
Primary mating contact 610149101. (May mate with other Receiver contacts, as well.)
-
Product
10 MHz to 40 GHz USB Wide Dynamic Range Peak and Average Power Sensor
U2064XA
Power Sensor
The Keysight U2064XA is a fast, accurate and wide dynamic range 10 MHz – 40 GHz USB peak and average power sensor.
-
Product
Inline Optical Power Meter - MATRIQ
1600 Series
Power Meter
The Power 1600 Series optical power meter provides quick and accurate inline power monitoring from -50 dBm to +20 dBm with 1, 2 or 4 channels in a compact form factor.
-
Product
Electronic Calibration Module, DC To 6.5 GHz, 2-Port
N7551A
Electronic Calibration Module
Reduce your calibration time by half with a smaller, lighter 2-port module that supports 3.5 mm or type-N 50 Ω connectors
-
Product
Flexible Cable Set, 3.5 Mm (Test Port) To 7 Mm
85132F
Calibration Cable
The Keysight 85132F is a 62.9 cm (24.75 in) long¹ flexible cable set composed of two 3.5 mm female² to 7 mm connectors. Cable frequency range is dc to 18 GHz with a return loss greater than or equal to 17 dB. Insertion loss is 0.25 * sqrt(f) + 0.2, where f is frequency in GHz, for the test port connector and device connector. Phase stability of semi-rigid/flexible cables is specified with a 90 degree bend using a 4 to 3 inch radius. Stability¹ of the Keysight 85132F is less than 0.12 dB and phase is 0.13 * f + 0.5, where f is frequency in GHz.
-
Product
Mini Power Contact, ITA, 65 Amp, 8 AWG
610115125
Power Contact (ITA)
Primary mating contact 610116112. (May mate with other Receiver contacts, as well.)Mini Power contacts carry up to 65 amps continuous current, 480 VAC. Maximum resistance is 1 Milliohms.
-
Product
72.5-Watt DC Power Line Conditioner w/Holdup
44KS3-02
Power Line Conditioner
NAI's 44KS3-02 is a 72.5-Watt Power Line Conditioner with holdup time that protects downstream DC/DC converters from transients, low voltage conditions, and power interruptions. This unit accepts +28 VDC input and provides a single output at 72.5 Watts either 22.5 to 30 VDC with holdup time or +16 VDC without holdup time - to all downstream DC/DC converters.
-
Product
10 MHz to 50/53 GHz USB Wide Dynamic Range Average Power Sensor
U2055XA
Power Sensor
The Keysight U2055XA is a fast, accurate and wide dynamic range 10 MHz – 50/53 GHz USB average power sensor.
-
Product
PXI/cPCI Programmable Power Supply - 16-bit Read Back Voltage and Current at Output
52912
Programmable Power Supply
Chroma 52912 programmable DC power supplies are designed specifically for test applications that demand precision output voltage/current and tightly coupled measurement capabilities.
-
Product
High Power Optical Head With Integrating Sphere
81628C
Optical Power Sensor
The 81628C High-Power Optical Head features an integrated sphere that enables it to handle power levels up to +40 dBm (with heat sink), across 800 nm to 1700 nm wavelength range. It provides the highest accuracy at high power within the family.
-
Product
Power Supply, 100 V, 50 A, 5000 W
N8759A
Power Supply
The Keysight N8759A power supply is a single output power supply in a small 2U package that offers essential features to fit your budget. The N8759A power cable offers flexible AC input options, analog / resistance control of output voltage and current, as well as parallel and series connection of multiple supplies to achieve more output current or voltage.
-
Product
100W Dual Output Power Supply Two 8V, 5A or 20V, 2.5A
E3648A
Power Supply
Keysight basic DC power supplies offer essential features for a tight budget. The single & dual output, 30-100 W GPIB E3640 series provide small, compact size for bench and system use; low output ripple and noise; and built-in measurements and basic programmable features with GPIB and RS232 interface. The Keysight 90W, multiple output E3648A is a clean, reliable power supply for general purpose applications, and combine convenient benchtop capabilities with flexible system features in a compact, multi-output package.
-
Product
Regenerative Power System, 2000 V, ±30 A, 20 KW, 400/480 VAC
RP7973A
DC Power Supply
The RP7973A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test.
-
Product
Power Supply Series
NGM200
Power Supply
Thanks to their high accuracy and fast load recovery time, the R&S®NGM200 power supplies are perfect for challenging applications. Their two-quadrant architecture allows them to function both as a source and a sink to simulate batteries and loads. Their short recovery times enable them to handle fast load changes that occur, for example, when mobile communications devices switch from sleep mode to transmit mode. High-speed data acquisition and convenient battery simulation widen the range of applications.
-
Product
E-Series Peak and Average Power Sensor, 50 MHz to 6 GHz
E9321A
Power Sensor
The E9321A power sensor has a 300 kHz video bandwidth and is ideal for time-gated peak, average and peak-to-average ratio power measurements on TDMA wireless formats such as NADC, GSM and EDGE.
