Showing results: 301 - 315 of 441 items found.
-
FAB105 -
Axiomtek Co., Ltd.
The FAB105 features a PICMG 1.3 CPU card slot, one PCI Express x16 slot, three 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. The FAB105 is perfect fit for AXIOMTEK's SHB100 and SHB110, which are built around the PICMG 1.3 form factor. The FAB105 is compatible with the AX60501 chassis.
-
FAB205 -
Axiomtek Co., Ltd.
The FAB205 features a PICMG 1.3 CPU card slot, five 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. The FAB205 is optimized to support AXIOMTEK's PICMG 1.3 system host boards, the SHB100 and SHB110, which are built around the PICMG 1.3 form factor. The FAB205 is compatible with the AX61220/AX61222 chassis.
-
Acromag, Inc.
High-performance 1/10-Gigabit Ethernet interface solutions for real-time and COTS data streaming applications. XMC modules provide a rugged, embedded computing platform for high-speed data communication in defense, aerospace, and industrial systems. Implementing a TCP offload engine (TOE processor) fully in hardware relieves the CPU from TCP/IP overhead and frees it to perform other tasks.
-
GX7000C -
Marvin Test Solutions, Inc.
The GX7000C Series are high-performance 20-slot PXI chassis that can accommodate up to 19 instruments as well as a PXI controller (an embedded CPU or a PXI bus expander interface such as the MXI series). The 6U form-factor provides the necessary real estate to accommodate high performance and high-density test instrumentation, while offering the flexibility of being able to use 3U PXI and cPCI instruments as well.
-
Silicon Software GmbH
The FPGA-based standardized image acquisition cards for image recording and processing stand out with their high-quality image pre-processing features, which reduce the CPU load to close to zero. The processing core of these cards consists of FPGA processors, which are distinguished by highly synchronizable data processing for high bandwidths. Through the graphic programming of the FPGA with VisualApplets, the cards can be adapted to new system requirements.
-
HGL Dynamics Inc
Hummingbird features a Gigabit Ethernet connection, allowing acquired data to be streamed to laptop or PC. It can also be used as a standalone data logger, with its built-in CPU and disk drive.The unit is supplied in an ultra-rugged milled aluminium housing for use in close proximity to the test article.The Hummingbird is completely compatible with HGL's existing range of data acquisition, real-time monitoring, analysis and archiving systems.
-
GX7000 Series -
Marvin Test Solutions, Inc.
The GX7000C Series are high-performance 20-slot PXI chassis that can accommodate up to 19 instruments as well as a PXI controller (an embedded CPU or a PXI bus expander interface such as the MXI series). The 6U form-factor provides the necessary real estate to accommodate high performance and high-density test instrumentation, while offering the flexibility of being able to use 3U PXI and cPCI instruments as well.
-
AS-FBD-1XCLD-2PE4L -
Active Silicon
FireBird Camera Link Deca Low Profile is a member of Active Silicon's state-of-the-art FireBird frame grabber family. The low profile design allows the FireBird Low Profile board to be used in small embedded PC enclosures and rackmount cases where full height PC cards are not suitable. A full height bracket option of this product is available for use in standard PC form factor enclosures. FireBird is designed for ultimate performance providing the very fastest image acquisition without any CPU intervention using the latest FPGA families, DDR3 memory, and a fast Gen2 PCI Express interface.
-
NI
PXI CAN Interface Modules communicate using onboard transceivers for High-Speed/Flexible Data‑Rate, Low-Speed/Fault Tolerant, and/or Single Wire CAN as well as any external transceiver. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. You can also import, edit, and use signals from FIBEX and DBC files in integrated CAN databases. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time.
-
Verified Systems International GMBH
The test system cluster architecture is based on dual CPU or 4-CPU PCs acting as cluster nodes. The nodes communicate and synchronise over a high-speed network (Myrinet or InfiniBand). A modification of the Linux operating system allows to run the test execution and evaluation algorithms in hard real-time on reserved CPUs, where scheduling is non-preemptive and controlled by the test system itself. The interrupts caused by interfaces to the system under test may be relayed to CPUs designated explicitly for their handling. This approach offers the opportunity to utilise high-performance standard hardware and the services provided by the widely accepted Linux operating system in combination with all mechanisms required for hard real-time computing. The cluster architecture presents an opportunity to distribute interfaces with high data throughput on different nodes, so that PCI bus overload can be avoided. In addition, the CPU load can be balanced by allocating test data generators, environment simulations and checkers for the behaviour of the system under test ("test oracles") on dedicated CPUs.
-
Bluey -
Electronut Labs
Bluey is a BLE (Bluetooth Low Energy) development board with Temperature, Humidity, Ambient Light and Accelerometer sensors. Bluey uses the Nordic nRF52832 BLE SoC (System on a Chip) which has an ARM Cortex-M4F CPU and a 2.4 GHz radio that supports BLE and other proprietary wireless protocols. It also supports NFC, and in fact the board comes with a built-in NFC PCB antenna. Open Source
-
Q7M311 -
Axiomtek Co., Ltd.
The Q7M311 has adopted the 14nm Intel® Pentium® N4200 and Celeron® N3350 quad-core/dual-core processors (codename: Apollo Lake). The extremely small embedded module supports 4GB (or optionally up to 8GB) DDR3L memory onboard and 32GB eMMC flash memory (optional). With a seismic design and for industrial-grade temperatures, both the CPU and the DDR3L RAM are soldered to deliver reliable and excellent computing performance. With rich features embedded in all the components built in a small form factor, the industrial-grade computer-on-module is aimed for industrial IoT applications, including industrial control, medical imaging, digital signage, gaming machines, military, and networking.
-
NI
CAN Interface Devices communicate using onboard transceivers for High-Speed/Flexible Data-Rate, Low-Speed/Fault-Tolerant, and/or Single-Wire CAN as well as any external transceiver. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. You can also import, edit, and use signals from Fieldbus Exchange Format (FIBEX) and Database Container (DBC) files in integrated CAN databases. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time.
-
cExpress-SL -
ADLINK Technology Inc.
The cExpress-SL is a COM Express® COM.0 R2.1 Type 6 Compact size module featuring the 64-bit 6th Generation Intel® Core™ i7/i5/i3 and Intel® Celeron® Ultra-Low TDP processors (formerly Sky Lake-U") with CPU, memory controller, graphics processor and I/O hub on a single chip. Leveraging the benefits provided by the 6th generation Intel® Core™ and Celeron® System-on-Chip, the cExpress-SL is specifically designed for customers who need optimum processing and graphics performance with suitable power consumption using Intel® Configurable TDP in a long product life solution.
-
M.2-COM-4SM Family -
Acces I/O Products, Inc.
The M.2-COM-4SM family of cards feature high performance 16C950-class UARTs. Available in 4-port and 2-port versions, each port is capable of communication speeds up to 921.6kbps in RS-232 (differential modes support speeds as high as 3Mbps) and has 128-byte deep transmit and receive FIFOs. Large FIFOs protect against data loss in multitasking operating systems, reduce CPU utilization, and improve data throughput, while reducing or eliminating inter-character or inter-packet pauses. The advanced integrated circuit with pre-scalar supports a wide variety of custom baud rates, and any rates not otherwise achievable can be supported via a custom factory-installed crystal oscillator (up to 10Mbps!).
