Dielectric Strength Testers
check insulation to assure current does not flow through it.
-
Product
Field Strength Meter
FIM-72A UHF
-
The Model FIM-72A is a portable, laboratory quality Field Strength Meter designed for rigorous field applications. Combining a calibrated half-wave dipole antenna and a highly accurate tuned voltmeter with a range of 140 dB, the FIM-72A is suitable for practically all types of RF emission measurements in the 450 MHz to 960 MHz spectrum. The operator can switch select wide or narrow bandwidth, peak or average value of TV or pulse modulated signals, AM or FM demodulation, and meter dynamic range of either 20 dB or 60 dB. A dc analog voltage, proportional to meter indication, is provided for driving a chart recorder or similar device. A leveled output from the calibrating generator is available for measuring cable insertion loss, filter response, amplifier gain, VSWR, and other signal ratio measurements. The 4-1/2 inch, taut band, mirrored scale meter is calibrated in volts and dB for precise measurements in field or laboratory environments.
-
Product
Insulating Oil Dielectric Loss Tester
HDLT
-
Hention Electrical Equipment Co., Ltd.
This integrated precious insulation oil dielectric loss tester is for measuring dielectric loss TAN and capacitance of transformer insulation oil.This is a high precision instrument; integrated with oil cup, temperature control instrument, temperature sensor, dielectric loss test bridge, AC test power, and standard capacitor, etc.
-
Product
PAM4 Bit Error Rate Tester.
BERT-1102
Tester
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
Product
Dielectric Probe Kit
N1501A
Accessory Kit
The Keysight N1501A dielectric probe kit with N1500A materials measurement software suite with Option 004, and a Keysight network analyzer, determines the intrinsic electromagnetic properties of many dielectric materials. Because these properties are determined by the molecular structure, they can be related to other properties of interest as well. Measuring them can provide critical insight into applications in many industries.
-
Product
Portable Single Yarn Strength Tester
TY420
-
TESTEX Testing Equipment Systems Ltd.
Portable Single Yarn Strength Tester. Used to test the breaking strength of yarn on the scene or in the lab. The instrument is controlled by micro computer. It can process the data automatically and send them to the printer. It is necessary & essential to estimate the technical index of the yarn.
-
Product
Compressive Strength
-
Compressive Strength testers are used to determine the compressive strength development, gel strength development and elastic moduli of oil well cement under simulated downhole conditions.
-
Product
Broadband Dielectric Spectroscopy
-
Material Sensing & Instrumentation
Broadband Dielectric Spectroscopy is a powerful tool for investigating a variety of dielectric processes for both electrical and non-electrical applications. Also called Impedance Spectroscopy, the measurement separates molecular process on the basis of response time, providing a unique relaxation frequency along with a signature variation with frequency.
-
Product
Shoe Dielectric Resistance Tester
UI-FT07
-
Shoe Dielectric Resistance Tester, also named as shoe high voltage withstand tester, is used to test shoe sole and heel electrical insulation, to check shoe performance of voltage withstand and current leakage. It is to test safety shoe dielectric resistance ability (Electrical Hazard Testing) as mentioned in ASTM F2412.
-
Product
Broadband Isotropic Field Strength Probes
PI-01, PI-01E, PI-03, PI-05
-
Modern design probes meeting the requirements of most EMC and RF safety standards for RF safety, industrial, military and radar communication applications: 0.2-1000 V/m, 10 KHz-40 GHz.
-
Product
Car-to-X Signal Strength Emulator
-
Qosmotec Software Solutions GmbH
QPER-C2X is a special adaptation of the signal strength emulator QPER, designed for mobile and Vehicular Ad-hoc Networks (MANet and VANet). Every radio devices in such an infrastructure-less network acts as a sender, receiver, and forwarder (router). Therefore, the ports of the QPER-C2X hardware are fully connected with each other by dynamically controllable attenuators. The system is fully designed for frequencies up to 6 GHz, since wireless communication for Intelligent Transport Systems (ITS) is based on the WLAN standard IEE 802.11p from 5.850 MHz to 5.925 MHz. The connected ITS stations can be either on-board units, as they are built into cars, or road side units that are used by road infrastructure (traffic lights, road work area delimiters, velocity signs). For tests in the lab, radio modules of such ITS stations are each kept in a shielding box that prevents any unwanted radiation over the air.
-
Product
ST Fully-auto BDV Dielectric Oil Tester Set
-
Chongqing Assen Power Equipment Co., Ltd
ST BDV Dielectric Oil Tester is ideal for speedy and accurate testing of dielectric strength of transformer and circuit breaker oil under-test room condition in accordance with international standard.
-
Product
Sliding Peel Strength Tester
OST3000
-
Compared to the scratch test, the friction and wear test is considered to be a durability evaluation method that is closer to the actual situation
-
Product
Dielectric Assessment Kit
DAK
-
Schmid & Partner Engineering AG
The Dielectric Assessment Kit (DAK) is ideal for all applications where high-precision dielectric parameter measurements (permittivity, conductivity, loss tangent) are required, including applications in the electronic, chemical, food, and medical industries. The dielectric probes are designed for fast, precise, non-destructive, and user-friendly measurements of liquids, solids and semi-solids over the 10 MHz – 67 GHz frequency range.
-
Product
Loss Tangent M in Dielectric Oil
TAND220A
-
The measuring instrument type TAND220A complies with the international standard IEC 61620. The instrument is based on the so-called "low-amplitude, low-frequency alternating current square wave method" and allows accurate measurements of conductivity and relative permittivity. Conductivity measurement in the range of 0.01 pS/m to 20,000 pS/m allows the use of this instrument for quality control of high resistivity liquids even at room temperature. The TAND220A works with a low test voltage and also with a low test current so that it does not represent a danger for the operators.
-
Product
Measures Wide Range of Anchor Strengths
Anchor Test System
-
Two models, each with two different gauge capabilities enable precision readings over a wide range of applications - from light to heavy duty loads. The standard system has a pull stroke of two inches with an option to extend to four inches. The longer pull stroke allows for complete extraction of most fixings in one simple operation. A load diffusion bridge and pyramid are available to keep reaction loads away from the anchor point.
-
Product
Portable System for High-Boltage Solid Dielectrics Testing
HVTS-70/50
-
Portable system HVTS-70/50 is designed for carrying out high-voltage withstand testing of cable insulation and other solid dielectrics with DC (rectified) voltage up to 70 kV and AC voltage up to 50 kV RMS at industrial frequency (f = 50 Hz).
-
Product
Testing Tensile Strength of Overlays, and Overlayments
James Bond Test ™ MK III
-
The James Pull Off Adhesion/Bond Tester measures the pull force used to pull a 2? or 3? disc away from the material being tested. This pressure is displayed on a precision gauge and can be related directly to the strength of the adhesion to the surface being tested.
-
Product
Dielectric Cure Monitoring Software
CureView
-
CureView dielectric cure monitoring software is a complete control and analysis package for operating all Lambient Technologies products. Our easy-to-use CureView software provides the flexibility needed in research and development along with user-configured operation for QA/QC and manufacturing applications.
-
Product
Strength Meter
NOVOTEST IPSM-U+T+D (Pulse Velocity Tester)
-
The pulse velocity tester IPSM-U+T+D allows to measure the strength and homogeneity of the concrete, bricks and other materials under the composition and surface sounding in products and designs for construction projects, inspection of buildings and structures, according to ASTM C597-16 (Standard Test Method for Pulse Velocity Through Concrete). Has the determining of the depth of cracks by the surface sounding probe function and also flaw detection mode (A-scan).
-
Product
Dielectric Test Fixture
16451B
Test Fixture
The 16451B is used to evaluate the dielectric constant of solid dielectric materials accurately, and complies with ASTM D150. The 16451B employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixture.
-
Product
Peel Strength Testers
-
Peel Strength Tester can be used for peeling, stripping and other performance tests of adhesives, adhesive tapes, pressure sensitive tapes, medical adhesive bandages, protection films, release paper, laminated films, leather, woven bags and paper.
-
Product
Pressley Fiber Bundle Strength Tester
F215
-
To determine the tensile strength of natural fibers. Includes 1 pair clamps and spacer, torque vice and wrench, cutter, comb and tweezers. A 5mg x 0.01mg capacity balance is required but not included.
-
Product
Dielectric Material Test Fixture
16453A
Test Fixture
The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.
-
Product
Gel Strength Test System
LD-LGST-A10
-
Gel Strength Test SystemLD-LGST-A10is mainly used to measure the gel strength of gelatine under the stipulated environment. It has traveling accuracy ± 0.3 % and Test range up to 5 to 1000 g Bloom. It consists of Jelly Strength Tester, Constant Temperature Bath and Refrigerator. Sampling depth can be present arbitrarily in 1 to 60 mm. It consists four kinds of sampling measurement modes: single-step, maintaining, circulating and automatic.
-
Product
IEC60884 Fig8 Plug Strength Compression Tester
IEC60884 fig8
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 fig8 plug strength compression testerConforms to the standard: GB2099-1-2008 Articles 10.1 and 24.5 and Figure 8, IEC60884-1 Figure 8
-
Product
Field Strength Meters
-
The FSM series of field strength meters will measure the strength of a RF signal appearing at its input from +20 dBm to -110 dBm for wide bandwidth models and +10 dBm to -120 dBm for narrow bandwidth models. The RF strength will be displayed on an LCD display to an accuracy of ±3 dB over the entire 130 dB dynamic range. A matching field signal generator is also available to act as a signal source for propagation studies.
-
Product
Extensometers for Creep Compliance and Tensile Strength Testing of Asphalt
Model 39
-
Jinan Testing Equipment IE Corporation
Designed to many of the needs for testing asphalt core samples in 4 and 6 i ch diameters. The unit meets test method requirements for strain measurement developed under the U.S. Federal Highways SHRP program.
-
Product
90° Peeling Strength Tester
SG-L09
-
This machine is used for testing the adhesive strength of copper-foil circuit on the PC board or tin-foil, aluminum-foil, tap,…etc, which are adhered to rhe suface of object.
-
Product
DIELECTRIC and CONTINUITY TESTERS ( HI-POTS )
AV-25V-GC1-05
-
This tester is designed for testing equipment wiht a line cord which can be plugged directly to the tester. The continuity test is to determine whether the ground wire of the line-cord is well connected to the metal frame of the unit under test.
-
Product
For Dielectric Oil Test
Stoil Cell
-
The option allows the testing of the insulation characteristics of the oil by checking if there is no contamination.
