Dielectric Strength Testers
check insulation to assure current does not flow through it.
-
Product
A C DIELECTRIC STRENGTH TESTERS ( HIPOTS )
AVC-50V
-
A C DIELECTRIC STRENGTH TESTERS ( HIPOTS ).
-
Product
AC & DC DIELECTRIC STRENGTH TESTERS ( HIPOTS )
AV/DV-25VA-5
-
A C & DC DIELECTRIC STRENGTH TESTERS ( HIPOTS ).
-
Product
A C & D C DIELECTRIC STRENGTH TESTERS ( HIPOTS )
AV/DV-50VA-10V
-
A C & D C DIELECTRIC STRENGTH TESTERS ( HIPOTS )
-
Product
Three Cups Insulation Oil Dielectric Strength Tester
STY Series
-
Chongqing Assen Power Equipment Co., Ltd
STY series three cups insulation oil dielectric strength tester uses a microprocessor to automatically complete boost, keep stirring, static discharge, calculate, print and other operations, is a necessary measure in the conventional test equipment.
-
Product
High Quality Transformer Oil Dielectric Strength Tester
AS-023A
-
Chongqing Assen Power Equipment Co., Ltd
AS-023A Series High Quality Intelligent Transformer Oil Dielectric Strength Tester is specially designed for testing dielectric strength (Breakdown Voltage) of transformer oil. The breakdown voltage (dielectric strength) is one of the most important parameters of transformer oil, it is a rule of the voltage withstand. The value of breakdown voltage (dielectric strength) indicates whether the oil contains water, impurity and electric particles, and you’ll know the oil value via the breakdown voltage (dielectric strength).
-
Product
D C DIELECTRIC STRENGTH TESTERS ( HIPOTS )
DV-25V-5
-
D C DIELECTRIC STRENGTH TESTERS ( HIPOTS ). One voltmeter 0-2500V dc accuracy: 2% of full scale. 4 Lights (power-on, high-voltage-on, fault and line-fault)
-
Product
A C DIELECTRIC STRENGTH TESTERS ( HIPOTS )
AVC-25V
-
A C DIELECTRIC STRENGTH TESTERS ( HIPOTS ). Two high-voltage leads, one c/w a clip and one c/w a retractable probe. Each is 2 meters (6 ft) long.
-
Product
Dielectric Strength Tester
HY
-
Chongqing Lushun Scientific & Technological Development Co., Ltd.
The instrument is designed and made as per the National Standard GB/T 507 "Test Methods for Breakdown Voltage of Lubricating Oil". It can be widely used to determine dielectric constant of lubricating oils in the field of railway, aviation, power plant, petroleum industry, and scientific institutes.
-
Product
D C DIELECTRIC STRENGTH TESTERS ( HIPOTS )
DV-50V-5
-
D C DIELECTRIC STRENGTH TESTERS ( HIPOTS )
-
Product
KVS Rugged Igniter Tester With Current Monitor
4314
Tester
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
Product
Automated Coherent Receiver Tester
CoRx Tester.
Receiver Tester
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
Product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
BUS Tester
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
Product
PAM4 Bit Error Rate Tester.
BERT-1102
Tester
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
Product
AXIe M8000 Series of BER Testers
Bit Error Rate Tester (BERT)
Simplified time-efficient testing is essential when you are developing next-generation computer, consumer, or communication devices. The Keysight M8000 Series is the highly integrated BER test solution for physical layer characterization, validation, and compliance testing. With support for a wide range of data rates and standards, the M8000 Series provides accurate, reliable results that accelerate your insight into the performance margins of high-speed digital devices.
-
Product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
Hoist Tester
Tester
The system has the capability of operating hyraulic powered hoists, DC powered hoists and 400Hz AC powered hoists. When a unit is connected to the system it is automatically detected and the system will load the unit's control software, acceptance procedures and operational safety limits. By doing all of this the operator does not need to worry about anything other than installing the unit and clicking Run to execute a full test procedure.
-
Product
MXE EMI Test Receiver, 3 Hz to 44 GHz
N9038B
Receiver Tester
The Keysight N9038B is a standards-compliant MXE EMI test receiver and diagnostic signal analyzer built on an upgradeable platform. You choose the frequency coverage you need to fully test devices with outstanding accuracy and sensitivity across required ranges.
-
Product
Gearbox Tester
Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
Product
64 Gbaud High-performance BERT
M8040A
Bit Error Rate Tester (BERT)
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
Product
MTM-Bus Tester
PXIe-1149.5
BUS Tester
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
Product
Automatic Dielectric Tester
LD-LADT-A10
-
Automatic Dielectric TesterLD-LADT-A10is a fully automatic oil tester. The oil tester adopts industrial SCM to control which is applied to integrate circuit. It features anti-jamming technology which largely improves the machine capacity.
-
Product
Dielectric Oil Testers
-
Electrical insulation oils form the critical insulation medium for many of today’s electrical apparatus, such as transformers, tap-changers, circuit breakers, cables, bucket trucks etc.
-
Product
Transformer Oil Dielectric Strength Testing
LS -JJ-II
-
Chongqing Lushun Scientific & Technological Development Co., Ltd.
1.The instrument has the function of automatic detection. 2.Tiny TPU-A panel printer is adopted for automatic printing out type insulating oil dielectric strength ATE is a full self-reacting device, which is developed according to the requirements in International IEC-156 and International GB507-86 "Insulating Oil Dielectric Strength Mensuration", combining the feedback opinions of all users .The instrument adopts singlechip as the leading part, and uses the method of "first setting and then testing". The whole process is controlled by automatic microcomputer. It is operated simply and used conveniently.
-
Product
Peel Strength Testers
-
Peel Strength Tester can be used for peeling, stripping and other performance tests of adhesives, adhesive tapes, pressure sensitive tapes, medical adhesive bandages, protection films, release paper, laminated films, leather, woven bags and paper.
-
Product
Leak and Seal Strength Tester
LSSD-01
-
LSSD-01 Leak and Seal Strength Tester is suitable for the quantitative measurement of sealing strength, heat sealing strength, binding strength, overall sealing performance, pressure resistance strength, cap body connection strength, bursting pressure and shedding strength. It is widely used in the soft package, plastic pilfer-proof caps, flexible pipes, etc.
-
Product
Bench top Dielectric Withstand tester
HYPOT III
-
RS-232 Interface available for automated controlPatented SmartGFI® functionPatented CAL-ALERT® functionComes complete with a test box for products terminated in a line cordPatented VERI-CHEK® functionStorage of up to 10 setups with 3 steps per setupBuilt-in security settingsDigitally controlled arc detection systemNo load setup of trip current and output voltageElectronic ramping (up & down)Built-in adjustable continuity testInterconnection to HYAMP® III to form complete test system
-
Product
Single Fiber Strength Tester
TB400C
-
TESTEX Testing Equipment Systems Ltd.
Single Fiber Strength Tester, suitable to test the tension strength and elongation of chemical fiber, cotton, wool, ramie, silk, glass fiber, fine metallic thread, etc.
-
Product
Pressley Fiber Bundle Strength Tester
F215
-
To determine the tensile strength of natural fibers. Includes 1 pair clamps and spacer, torque vice and wrench, cutter, comb and tweezers. A 5mg x 0.01mg capacity balance is required but not included.
-
Product
Strength Testing
-
Sataton Instruments Technology CO., Ltd
Air permeability tester is professional designed to determine the permeability of materials to air. By testing the rate of flow of air passing perpendicularly through a given area of tested sample under a given pressure over a given time period, the tester can provide results of air permeability performance by calculation the indices. The air permeability testing instrument is applicable to many type of materials, including industrial fabrics, nonwovens, made-up textiles, paper and board, foam and other materials.
-
Product
Liquid Dielectric Test Cell
LT-4123
-
The LT-4123 Liquid Dielectric Test Cell is designed for testing the quality of materials such as the insulating oils used in transformers and the resins used in the manufacture of thermosets. With the LT-4123 Liquid Dielectric Test Cell, users can measure the AC loss characteristics and permittivity of liquids. The data gleaned from these measurements are used to set quality benchmarks for fluids during testing and manufacturing.
