ECU Testing
test of Electronic Control Unit (Engine Control Unit) validating it and related dynamic systems.
See Also: ECU, ECU Simulation
-
Product
Functional Test System
TS-5040
Functional Test
The Keysight TS-5040 Functional Test System is a cost effective, robust and reliable test system that gives you the lowest cost of ownership. In addition, the open architecture Test Exec SL gives you the flexibility to do just about anything you want.
-
Product
Infotainment Test for Automotive Applications
test
Multimedia operating interfaces are complex control and display devices for functions such as entertainment, telephony, on-board computers and vehicle settings. The functional test of such complex control units and their networking within the vehicle architecture presents a particular challenge in every phase of the product design process.
-
Product
Fully-Automated CTIA-Compliant OTA Test System
TS8991
Test System
The R&S®TS8991 OTA performance test system measures the spatial radiation and sensitivity characteristic as specified by CTIA and 3GPP.The system software provides ready-to-use test templates for OTA measurements and supports all wireless standards.The integrated report function collects all measured test data such as graphics or numeric results, test environments, EUT information and hardware setup in one document.
-
Product
In-Circuit Testing and Test Engineering
GenRad 2287
-
3560 Hybrid Test NodesWindows InterfaceTotal GenRad 227X Migration Capability20 Mhz Clock, Sync, and Trigger, 5 Mhz data ratesVector Test for VLSI, PLCC’s & ASICSTest Express Vectorless TestingMultiple Chain Boundary ScanAnalog Functional Test Module
-
Product
Photodiode Burn-in Reliability Test System
58606
Test System
The Chroma 58606 PD/APD Burn-in system is a high density, multifunction and temperature controlled module based system for photo diode burn-in and lifetime test. Each module has up to 256 Source Measurement Unit channels which can source current and measure voltage in various scenarios such as one described below. The system can accommodate 7 modules for a total of 1,792 device channels.
-
Product
Regenerative Battery Pack Test System
17020E
Test System
Charge/discharge modes (CC, CV, CP)Power Range: 10kW / 20kW per channelVoltage Range: 60V/ 100VCurrent Range: 100A/200A/300A/400A/ 500A/600A/700A/800A per channelRegenerative battery energy discharge, efficiency 85%Channels paralleled for higher currentsDriving cycle simulationFast current conversion without current interruptHigh precision measurementSmooth current without over shootTest data analysis functionData recovery protection (after power failure)Independent protection of multi-channel
-
Product
Shock Test System, Battery Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's shock test system used to measure and determine the impact resistance of a product or package. It is mainly used to evaluate the reliability of the function and the integrity of the structure of the test product under impact environment. Suitable for impact testing of aerospace, aerospace, marine, military, consumer electronics, automotive, household appliances and display equipment.
-
Product
Testing And Simulation
-
Uni- and bidirectional power supplies for testing and simulating batteries, fuel cells, electric drive trains and other components.
-
Product
Test Socket
-
Our test sockets are made for high performance and are of top quality, to guarantee a smooth, effortless process. We believe in providing our partners and customers with effective and intelligent solutions that they can apply with ease. Choose the solutions of TTS Group cater to the needs of detailed and complex systems.
-
Product
Laser Testing
-
CI Systems provides a wide range of laser testers, whether stand-alone systems, such as Depot Field Laser Tester, Depot Laser Tester or integrated in a multi-sensor electro-optical test bench. These testers can also be integrated with CI Systems' standard Laser Tester software and PC package to serve as the necessary testing tool for a larger system comprising a Laser Range Finder, Laser Marker and Laser Designator.
-
Product
Speaker Test
-
Determines speaker polarity by analyzing a proprietary signal. See our new demo video of this module. Measures woofers, midrange, and tweeter drivers.
-
Product
Test & Measurement
-
Blonder Tongue Laboratories, Inc.
Tools to assist in video delivery installations, Blonder Tongue’s collection of Test & Measurement handheld products are second to none in capturing data for troubleshooting and testing purposes. These units provide real-time spectrum analysis, making them invaluable to those in the field.
-
Product
Sencha Test
-
Sencha Test is the most comprehensive unit and end-to-end testing solution for Ext JS apps. Based on years of testing Ext JS applications and the deepest integration with the framework, Sencha Test helps you improve application quality, accelerate time to market, and reduce testing time and costs. With Sencha Test, you can create unit and end-to-end tests quickly, and execute them on multiple browsers simultaneously. Cross-browser testing is critical to ensuring quality for organizations, and test automation is a requirement to meet delivery timelines. Sencha Test is the only dedicated testing solution for Ext JS applications. It helps you build an end-to-end testing plan without having to cobble together testing tools.
-
Product
Electrical Testing
-
Innovative Testing Solutions, Inc.
Our specialty is Direct Current automotive components. We perform product validation and design verification testing on both electrical components and systems. Also, we perform warranty investigation testing and failure analysis. We have voltage capabilities to 300 volts and current capabilities to 1000 amperes. Both two-wire and four-wire resistance measurements are supported from NanoOhms to GigaOhms.
-
Product
Test Technology
GLP3
-
The GLP3-Windows®-testers are our premium testers to test a variety of different complex products. They are preferably used to test electric component groups, run-in test benches, power supplies, cables, washing machines and more and are ideally suited for complex test benches and inerlinkes assembly- and test lines.
-
Product
Test Sockets
Non Standard
-
Chances are good Ardent can help you with that. We can adapt our technology to just about any package, device or module. Small volumes of custom sockets for higher bandwidth applications are a niche all in their own, and our engineering team has many years of experience designing custom sockets for all kinds of applications.
-
Product
Optical Test
-
Optical components such as micro-lenses, diffractive optical elements (DOE), meta optical elements (MOE) and micro lens arrays (MLA) are now largely used on consumer electronics and even more optical elements need to be integrated into smaller and smaller packages. Nowadays mass-production industries key to success lies in increasing the yield by means of strongly automatized testing machines, with statistical analysis.
-
Product
ECU & Bus Interface Modules
ES500
-
ETAS makes the entire software and hardware range available from program development to the calibration of your ECUs. You can use the ETAS tools to address all ECUs that satisfy the ASAM standard. By using these standardized interfaces, our tools are not limited to the ECUs of any particular manufacturer.
-
Product
Radio Testing
-
Testing of radio systems. PHOENIX TESTLAB as an accredited radio testing laboratory, Notified Body for R&TTE Directive 99/5/EC and Conformity Assessment Body offers you a complete service up to your products' worldwide introduction to the market.
-
Product
Performance Testing
-
LOAD TESTINGEvaluates software behavior under a specific expected loadVOLUME TESTINGEvaluates software productivity under an increasing volume of stored and processed dataSTABILITY TESTINGDetermines the effect of configuration changes on the system's performance and behaviorSTRESS TESTINGIdentifies the upper limits of software capacitySCALABILITY TESTINGMeasures software capability under increased processing power and architecture changesCONFIGURATION TESTINGDetermines the effect of configuration changes on the system's performance and behavior
-
-
Product
Test & Evaluation
-
We are a world-leader in the provision of relevant Test & Evaluation services, an enabler to the delivery of advanced defence capability.
-
Product
Test Hardware
TTPSimulate PCI
-
TTPSimulate supports hardware-in-the-loop simulation and design of complex distributed control systems where some parts of the systems are physically available and others exist only as a simulation model. This board enables concurrent engineering and reliable integration of complex integrated systems in large programs.
-
Product
EMI Testing
-
Independent Testing Laboratories
ITL offers compliance and qualification testing for virtually any type of electronic product or system.
-
Product
Test & Inspection
-
Our test and inspection products support maintenance, product quality testing, diagnostics, and quality control. The extensive range of products covers almost any application need you to have.
-
Product
Metallurgical/Metallographic Testing
-
A partial view of our Metallurgical examination areas, showing metallurgical microscopes with digital filar micrometers. These instruments, along with our cross-sectioning and polishing equipment, make the Optical Metallography facilities at Pacific Testing among the most extensive in the industry. In addition, these facilites are under the supervision of our Chief Metallurgist, with a Ph.D. in Metallurgy.
-
Product
Noise Test
-
As experts in the acoustic industry, our company offers a wide range of noise monitoring equipment, including sound level meters, monitoring substations, and noise localization devices. We also provide customized solutions to meet specific scenarios and requirements for noise control.
-
Product
Test Panel
TA-5
-
A complete NAV/LOC/GS/MKR test panel designed around the VIR30/31/32 units. Requires channeling source. Combining the TA-6 panel provides a complete integrated system.
-
Product
Reliability Testing
-
ELES Semiconductor Equipment SpA
ELES designs and manufacturers reliability test solutions to verify the performance of integrated circuits from concept validation to high volume production during all the test phases. No other company can provide universal equipment for all the reliability tests, or can guarantee a seamless data flow between phases or can apply on chip embedded reliability engineering for data tracking and failure investigation. Clients use our functional test data to proactively analyse variations between lots, between temperature extremes and during lifetime (often these defects escape ATE). The improvements to products and processes needed to arrive at zero defects cannot be driven by the quantity of Big Data alone, the quality of reliability data is a strategic advantage that only ELES can provide.
-
Product
Vehicle Testing
-
short testing times, thereby enabling a large throughput of vehicles;objective, operator independent test results on most test items;accurate measurements;a large set of clear user instructions is displayed, which allows the owner/ driver to stay in the vehicle during the test, thus saving manpower;a wide selection of different test equipment for integration is available;a large number of settings, threshold values and standards can be accessed directly and edited by the user;the modular setup allows a complete variety of Test Lane configurations;easily upgradable by adding more test equipment items per lane;easily expandable by adding more Test Lanes;integration of Test Lanes on remote sites is possible;link up to Government database and remote access possibilities where applicable.
