-
Product
SWR/ Power Meters
SX600/SX600N
-
Frequency range:1.8 to 525MHz/S1(1.8 to 160MHz), S2(140 to 525MHz). Power display range:5W 20W 200W. Accuracy at full scale:±10%. Minimum power at SWR measurement:S1(1W), S2(4W)
-
Product
1.8 - 525 MHz GrandMaster SWR Meter
MFJ-874
-
MFJ Grandmaster SWR/Power meters are the Cadillacs of ham radio! All GrandMaster feature peak and average, forward and reflected power readings and have selectable power ranges. Covers HF /UHF / VHF. 30, 300, 3000 Watt power ranges.
-
Product
SWR / Power Meters
SX27P
-
Frequency range:140 to 150MHz/430 to 450MHz Power display range:15W 60W. Minimum power at SWR measurement:0.1W 60W. Insertion loss:Less than 0.3dB. Measurement function:Forward Rf
-
Product
SWR / Power Meters
SX240C
-
Dimensions:170Wx115Hx150DmmWeight:1350gFrequency range:S1 (1.8-54MHz) S2 (140-470MHz)Power display rating:30W/300W/3kW(HF band only)Accuracy of full scale:±10%(F.S.)
-
Product
SWR / Power Meters
SX200
-
Frequency range:1.8 to 200MHz. Power display range:5W 20W 200W. Accuracy at full scale:5W Range ±5%(F.S),20W Range ±7.5%(F.S),200W Range ±5%(F.S), (Add +15% of full scale at 160 to 200MHz). Minimum power at SWR
-
Product
SWR / Power Meters
-
A device used primarily by radio operators to measure the Standing Wave Ratio (SWR) and forward and reflected power in a transmission line, like a coaxial cable.
-
Product
Coaxial Fixed Attenuator, DC to 12.4 GHz
8491A
Attenuator
The Keysight 8491A coaxial fixed attenuator provides precision attenuation, flat frequency response and low SWR over broad frequency ranges. The attenuator has type-N connectors and is available in nominal attenuations of 3 dB and 6 dB, as well as 10 dB increments from 10 dB to 60 dB. This attenuator is swept-frequency tested to ensure specification compliance at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
Product
Biconic Logarithmic Periodic Antennas
Stacked LPDA
-
The stacked Logarithmic Periodic Dipole Antenna consists of two ordinary Log.-Per. structures. The excellent characteristics (flat gain over a large bandwidth, low SWR) of the ordinary Log.-Per. designs could be maintained using the stacked LP design. The stacked design helps to focus the directional pattern of the H-plane somewhat, resulting in a typical gain improvement of ca. 2-3 dB compared to an ordinary LPDA. This is especially important for immunity testing, where a maximum fieldstrength and a good field uniformity is required. The beamwidth in the E-plane and the H-plane are nearly identical, providing an optimised illumination of the EuT with minimised ground reflection influence. Further the STLP 9128 C has an excellent cross-polar rejection.
-
Product
Programmable Step Attenuator, DC to 26.5 GHz, 0 to 70 dB, 10 dB steps
84907K
Attenuator
The Keysight 84907K programmable step attenuator offers coaxial measurements to 26.5 GHz in a compact, rugged design. It offers repeatability of better than 0.03 dB, excellent life (greater than 5 million switching cycles per section) and an attenuation range of 0 to 70 dB in 10-dB steps. This latest design evolution sets new standards for size and performance. High attenuation accuracy and low SWR are achieved through the use of miniature thin-film attenuation cards composed of high-stability tantalum nitride film of saphire substrate. Insertion loss is outstanding, with less than 2 dB of loss at 26.5 GHz. The compact size of the unit, 35 percent smaller than the Keysight 8495/7 26.5 GHz) family, allows for easy integration into instruments and ATE systems.
-
Product
Manual Step Attenuator, DC to 26.5 GHz, 0 to 70 dB, 10 dB steps
8495D
Attenuator
The Keysight 8495D dc to 26.5 GHz manual step attenuator offers exceptional repeatability and reliability. Attenuation is provided in 10 dB steps from 0 to 70 dB. Precision gold-plated leaf springs ensure long life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
-
Product
Coaxial Attenuators Set
11582A
Attenuator
The Keysight 11582A contains a set of four 8491B attenuators 3, 6, 10, and 20 dB furnished in a handsome walnut accessory case. The Keysight 8491B are type-N connectors with a maximum frequency of 18 GHz. This set is ideal for calibration labs or where precise knowledge of attenuation and SWR is desired.
-
Product
Low Noise Amplifiers for Radio Amateurs
-
Our Low Noise Preamplifiers are remarkable for extremely low noise, excellent SWR, high efficiency and a high IP3. The Low Noise amplifiers are especially selective and absolute stable therefore oscillation is avoided. Even if you have a bad SWR. This is the reason why radio amateurs and club-stations all around the world trust in Kuhne electronic equipment. The products are perfect for use in contests, EME, MeteorScatter, Aurora and Tropo DX. Small mechanical measurements and technical innovations from the professional sector, e. g. milled aluminium cases, enable high temperature stability and tower mounting. Numerous contest victories, records and first contacts with a country were and are achieved with Kuhne products. Don't compromise and get technology from Kuhne electronic!
-
Product
Remote Antenna Switch
RATPak System
-
This switch is designed to give you reliable performance even at veryhigh power and SWR levels. This indeed should be the last antennaswitch you should have to purchase. It is also designed so that in caseof a failure of a relay or other device, it can be easily disassembled and repaired. This is not the least expensive switch on the market but we believe you will appreciate the quality that went into its design.
-
Product
Power Meters
SX1100
-
Frequency range:S1 (1.8-160MHz)S2 (430-450MHz/800-930MHz/1240-1300MHz)Power display range:5W/20W/200WAccuracy at full scale:±10% (F.S.)Minimum power at SWR
-
Product
Programmable Step Attenuator, DC to 40 GHz, 0 to 11 dB, 1 dB steps
84904L
Attenuator
The Keysight 84904L programmable step attenuator offers coaxial measurements to 40 GHz in a compact, rugged design. It offers repeatability of better than 0.03 dB, excellent life (greater than 5 million switching cycles per section) and an attenuation range of 0 to 11 dB in 1-dB steps. This latest design evolution sets new standards for size and performance. High attenuation accuracy and low SWR are achieved through the use of miniature thin-film attenuation cards composed of high-stability tantalum nitride film of saphire substrate. Insertion loss is outstanding, with with only 2.4 dB of loss at 40 GHz. The compact size of the unit, 35% smaller than the Keysight 8495/7 (26.5 GHz) family, allows for easy integration into instruments and ATE systems.
-
Product
SWR / Power Meters
SX400/SX400N
-
Frequency range:140 to 525MHz. Power display range:5W 20W 200W. Accuracy at full scale:5W Range ±10%(F.S),20W Range ±5%(F.S),200W Range ±5%(F.S), (Add -10% of full scale at 220 to 420MHz, add +10% of full scale at 450 to 525MHz). Minimum power at SWR measurement:4W
-
Product
Wattmeters
-
Monitor 4 sensors simultaneously for peak, Average power and coax SWR. Direct USB 2.0 full speed interface. Backlit LCD display for stand-alone operation- Your PC is optional. Oscilloscope and Spectrum Analysis of the RF Modulation- Observe IM and "Splatter" frequency components realtime. Complete system includes (1) sensor, WN-2 unit, AC power module and software on CDROM. Wide range of sensors cover 100 milliwatt to 8KW, 1.6 Mhz to 470 Mhz.
-
Product
Antenna Tuner
DU-1500L
-
Model DU 1500 L is high power antenna tuner that uses and adjustable reactive network for matching the unbalanced 50 ohm output impedance of transmitters and transceivers to a variety of balanced and unbalanced loads.It is usable over a frequency range of 1.8-30 MHz. Provision is made for selecting one of three antennas or for bypassing the matching network.A crossed needles SWR and wattmeter with switchable 200 and 2000 watt scales and selectable peak and average power output reading is included.
-
Product
Power Sensors
8480 Series
-
The 8480 thermocouple and diode power sensors series provide extraordinary accuracy, stability, and SWR over a wide range of frequencies and power levels.50 dB dynamic range (maximum) over –70 to +44 dBmFrequency range from 100 kHz to 110 GHz (sensor dependent)Accurate average power measurementsRange of thermocouple and diode power sensorsCompatible with EPM, EPM-P, P-series, and E1416A power meters
-
Product
Coaxial Waveguide Adapter, APC-7, 12.4 to 18 GHz
P281B
Coax Adapter
The Keysight P281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Coaxial Waveguide Adapter, APC-7, 12.4 to 18 GHz
P281C
Coax Adapter
The Keysight P281C adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
VNA & SWR Site Analyzers
6050
-
SWR Site Analyzer with VSWR, Return Loss and FDR (Frequency Domain Reflectometer) measurements. VNA Site Analyzer with full Vector Network Analyzer measurement suite S11 and S21 ports, Spectrum Analyzer, Power Meter and FDR (Frequency Domain Reflectometer) measurements. Quickly shift between VNA and SWR/Return Loss only.
-
Product
Antenna Tuner
DU-1500T
-
The DU 1500T optimizes the performance of your antenna and transmitter or SWL receiver by providing adjustable impedance matching.The DU1500T also measures the Power and Standing Wave Ratio (SWR), which allows you to tune the indicted SWR to the lowestpossible ratio for the selected transmit frequency.
-
Product
Wideband Swept Antenna, Cable Analyzer
SWR TRUE 3013
-
• A cost-effective SWR Analyzer covering all Cellular and radio communication bands 30-2700 MHz• Measures transmition & antenna impedance, frequency, SWR, return loss, and bandwidth by sweeping band of interest• Built-in synthesized RF sweep generator• SWR TRUE 3013 Antenna Analyzer gives you quick and reliable antenna and cable trouble-shooting capabilities• 5 in 1 analyzes for antenna tuning and control• Measured results can be stored for further analyzing and documentation on internal and external storage media• Time stamp and operator ID capability included• LCD Display works in direct sunlight and with backlight in dark areas
-
Product
Manual Step Attenuator, DC to 18 GHz, 0 to 110 dB, 10 dB steps
8496B
Attenuator
The Keysight 8496B dc to 18 GHz manual step attenuator offers exceptional repeatability and reliability. Attenuation is provided in 10 dB steps from 0 to 110 dB. Precision gold-plated leaf springs ensure long life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
-
Product
Manual Step Attenuator, DC to 4 GHz, 0 to 110 dB, 10 dB steps
8496A
Attenuator
The Keysight 8496A dc to 4 GHz manual step attenuator offers exceptional repeatability and reliability. Attenuation is provided in 10 dB steps from 0 to 110 dB. Precision gold-plated leaf springs ensure long life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
-
Product
Mobile Watt Meter
PM2000AM
-
The PM2000AM Mobile measures and displays forward power, reflected power, and SWR simultaneously on it's dual movement meter system in the frequency range. Accuracy of the readings is assured because the PM2000AM features a true shielded directional coupler, that on the mobile version is offered as an external unit. The backlit meter can display either peak or average power readings, and has 300 and 3000 watt range settings.
-
Product
SWR True Antenna Analyzer
-
SWR True Antenna Analyzer is a versatile analyzer covering all major communication bands from 30MHz to 2700MHz. The SWR True will analyze antennas and cables. Measurements are represented graphically as VSWR or Return Loss plots. The built in PLL synthesized generator offers a superior accuracy with small step size. The internal operating system controls measurement, display and the I/Os allowing serial communication to PC, USB to memory stick and USB Serial communication. The I/O options are used to write plots to either memory sticks or to a connected PC, the I/Os can also be used to operate the instrument, giving commands and receiving data. For documentation reference the instrument has a real time clock. Multilayer menus are used to setup and control the operation of parameters. The SWR True instrument is small, handy and light weight battery operated with more than 6 hours of continuous operation on the internal NiMh cells. Feature with XML data handling and application viewer is included. Accessory kit with soft carrying bag, car charger and coax adapters for standard types.
-
Product
Waveguide Power Sensor
Q8486D
Power Sensor
Excellent SWR for reducing mismatch uncertainty50 MHz calibration port Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter Accurate average power measurements over -70 to -20 dBm Frequency range 33 GHz to 50 GHz Diode power sensing element
-
Product
Antenna Tuners
DU-3000T / DU-3000TB
-
The DU 3000T and DU3000TB tuners optimize the performance of your antenna and transmitter or SWL receiver by providing adjustable impedance matching. The DU 3000 series also measure the Power and Standing Wave Ratio (SWR), which allows you to tune the indicated SWR to the lowest possible value for the selected transmitfrequency.
