Absorbing Clamps
measure radiated emissions. Also known as: Ferrite Clamps
-
Product
Standard Clamp Meters
-
For extreme temperatures, choose an analog clamp meter that can measure amps and volts without needing batteries.
-
Product
AC/DC Mini Digital Clamp Tester (CE)
M-290RMS
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*30mmφ CT window and ultra compact size.*Conform to IEC safety requirements.*True rms reading for ACA and ACV.*Data-hold function and auto power off.*Auto zero adjustment for DC current offset.
-
Product
Clamp type AC Current Sensor／for Power Monitor
ZCT-40P
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC 0.1A～500A*Current measurements of feeder
-
Product
Earth Resistance Clamp Meter
T2100
-
Clamp meters for measuring earth resistance directly on earth rods (STAKELESS METHOD) and compatible with MacrotestG series meters
-
Product
TRUE RMS AC Clamp Meter
2960 CL
-
Standard Electric Works Co., Ltd
● True RMS measurement.● Pocket size.● 4000 counts.● Full automatic measurement. Voltage measurement. Current measurement. Resistor measurement.● Data hold function.● Continuity check.● Diode measurement.● Select function.● Low battery indication.● Auto off function.● Flashlight (Auto off in 1 minute).● Re-power on by pushing any of the push buttons or by changing the rotary switch mode after auto power off.
-
Product
Digital Ior Leakage Current Clamp Tester
MCL-400IR+
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・About Ior Leakage CurrentRecently, the leakage current clamp meter is widely used for insulation control of low voltage circuit as the supplementary method of the insulation resistance measurement. The control of leakage current has the advantages to enable the prediction of insulation condition in the electrical power line without having to shut off the power. The leakage current (Io) includes the capacitive leakage current (Ioc)originated in the capacitance and the resistive leakage current (Ior) originated in the insulation resistance each related to the ground. It is considered that the measurement of resistive leakage current (Ior) is the very useful and effective method for the insulation control of low voltage circuit. However, it was difficult to measure the resistive leakage current (Ior)with traditional leakage current clamp meter. MCL-400IR new digital clamp tester enabled the measurements of the resistive leakage current (Ior)without voltage input(phase detection).
-
Product
16-to-16 Pin Cable Kit For Y1150A/51A/52A/53A/54A/55A
Y1159A
Cable Clamp Kit
Kit comes with supplies to build 2 cables for Y1150A/51A/52A/53A/54A/55A
-
Product
Current Clamp Adapter
-
PeakTech Prüf- und Messtechnik GmbH
It uses a pair of jaw which allow clamping around an electrical conductor to measure the current in a conductor without the need to make physical contact unlike a normal multimeter.
-
Product
C/I Clamp Meters
CLAMPMETER, 400A AC (CM-410)
-
*Measures to 600 volts AC and DC, and 400 amps AC*Data hold to capture important readings*Audible continuity test*Auto power off for longer battery life*Accessories included: (2) 1.5V AAA batteries, test leads, carrying case*Lifetime Limited Warranty
-
Product
Non-contact Io/Ior Leakage Clamp Meter
MCL-800IRV
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Safety by non-contact sensor, not touching live part directly (prevention of electric shock, short-circuit, etc.).・Easy to carry and operate, clamp CT + display part integrated type.・Measurable line current + leakage current + resistive leakage current by one unit.・Available direct voltage input at live part as ordinary.・Calculable insulation resistance value（MΩ）by voltage & current (only in case of using direct voltage input sensors)・Available measurement for 3P/4W star connection.
-
Product
IND AC/DC CAT IV TRMS Clamp Meter
ACDC-3400
-
The Amprobe ACDC-3400 clamp multimeter is CAT IV rated to add an extra level of safety for high voltage, industrial or utility testing applications. It is an AC/DC current clamp meter and a voltage meter all in one.
-
Product
DC/AC Clamp Meters
-
ACA/DCA measurement up to 999.9A.All of function from new microprocessor technology.Inrush current(100ms) mode, for measuring start current formotors, lighting, etc.
-
Product
AC/DC Digital Clamp Tester
TCM-45E
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Unique opening / closing mechanism that can measure even in narrow places*AC / DC both 10A / 100A 2 range switching Φ45mm CT inner diameter*RMS value measurement that can accurately measure even distorted waveforms
-
Product
ITA, iCon, Extended Cable Clamp
410123115
ITA
This iCon ITA includes an extended cable clamp to accommodate larger cable bundles. The maximum cable bundle area = 1.97 " sq. or a 1.58"/40.13mm diameter bundle. The clamp may be inverted for smaller cable bundles.Please note: This ITA does not offer an increased bend radius that may occur with a larger cable bundle radius. Larger bend radius is offered by the iCon XL, p/n 410123232.
-
Product
AC Clamp Meter
ST-2600
-
Standard Electric Works Co., Ltd
● Full auto range for V.A and Ω functions. ● Data hold function freezes the reading in dimly lit or hard to reach places. ● Low battery indication. ● Built-in buzzer for continuity test.● Safety design throughout with no exposed metal parts. Shielded banana plugs and recessed input terminals.● Ohm function ideal for checking continuity of relays transformers and motor coils.
-
Product
AC/DC Mini Digital Clamp Tester (CE)
M-280
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
30mmφ CT window and ultra compact size. Conform to IEC safety requirements. Low cost and multi-function clamp tester. Max. and Min.hold function. Data-hold function and auto power off. Auto zero adjustment for DC current offset.
-
Product
Digital Clamp Tester With Big CT Window (CE)
MCL-1100D
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
This handy type clamp tester has the biggest CT window in the world (108mmx128mm) and can measure AC load current and leakage current (0.1mA-3000A) just by clamping the conductor without disconnecting the circuit.
-
Product
Clamp Meter AC Current 1999 Counts
VA310 VA310C
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Diode Test Back Light Continuity Buzzer.
-
Product
AC Current Clamp Adapter
LAD-1100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
●Selectable measuring range 30mA~30A with CT ratio 10:1 and 30A~3000A with CT ratio 100:1.●φ110mm CT window, possible to measure from leakage to big current up to 3000A.
-
Product
AC/DC Clamp Meter
3801 CL
-
Standard Electric Works Co., Ltd
● Full auto range for V.A and Ω functions.● LCD backlight display.● Flashlight function.● Data hold function freezes the reading in dimly lit or hard to reach places.● Low battery indication.● Built-in buzzer for continuity test.● Safety design throughout with no exposed metal parts. Shielded banana plugs and recessed input terminals.● Ohm function ideal for checking continuity of relays transformers and motor coils.
-
Product
AC/DC Clamp Milliammeter (CE)
M-700
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High sensitive for low range leakage current.*Suitable for measurement of 4-20mA DC controlled circuit.*DC mV analog signal output.*Lowest influence from Magnetization and Terrestrial magnetism.*Wide measuring ranges up to DC 1000mA and AC 10A.
-
-
Product
Clamp Meters
-
An electrical testing tool that integrates a basic digital multimeter with a current sensor. Clamps measure current.
-
Product
True RMS Clamp Meter w/ ATTPC3
DL389BCOMBO
-
UEi Test & Measurement Instruments
True RMS Dual Display Clamp Meter w/ Temperature and ATTPC3
-
Product
TightSight™ Clamp Meter, 660A AC/DC W/TRMS
61-765
-
*TightSight™ bottom display*Tapered jaws with hook tip*True RMS current and voltage*AC/DC voltage*Audible continuity*High frequency rejection**Peak hold*Max/min hold*Data hold*Selectable audible and visual alerts when potentially hazardous voltages are detected at the probe terminals*Selectable auto power off*Backlit display*Low battery indicator*Reads accurately on noisy electrical circuits
-
Product
Clamp type DC/AC Current Sensor／with Voltage Output
LAD-240
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*With DC voltage output*DC 1A～200A
-
Product
Cobb Absorbency Tester
DRK110
-
Shandong Drick Instruments Co., Ltd.
DRK110 Cobb Absorbency Tester is used to test the absorbency of paper and cardboard according to related standards.
-
Product
Clamp Meters
-
Klein Tools' line of clamp meters is designed to give professionals increased accuracy and easy to read results regardless of what the job requires. These meters are built to stand up to tough jobsite conditions and have been designed with specific trades in mind.
-
Product
AC/DC Clamp Meter
3900 CL
-
Standard Electric Works Co., Ltd
● 4000- count LCD.● Full automatic measurement. ◎ Voltage measurement. ◎ Current measurement. ◎ Resistor measurement. ◎ External frequency measurement.● Range change function.● Data Hold function freezes the reading.● REL function.● Peak function.● VAHz mode measures frequency in ACV and ACA mode.● Max/Min function.● Continuity check.● Low battery indication.● Auto Power Off (APO) function.● Safety design throughout with no exposed metal parts, shielded banana plugs and recessed input terminals.
-
Product
Compact AC Auto Ranging Clamp Meter
410001
-
The small bodies and jaws fit perfectly in your hand and into tight places. Meter controls are positioned so that current measurements can be done with one hand. A large backlit display is easy to see, and the handy display hold function keeps measurements fixed on the display. Measures starting current for motors, lighting, etc.
