Partial Discharge Test
See Also: Partial Discharge, Partial Discharge Detection, Partial Discharge Monitors, PD, PD Test
-
Product
Dielectric Test Fixture
16451B
-
The 16451B is used to evaluate the dielectric constant of solid dielectric materials accurately, and complies with ASTM D150. The 16451B employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixture.
-
Product
Other Test Systems
-
Your business challenges do not fit the typical mold. Your test requirements are different. Ball Systems has more than 50 years of experience in multiple industries that has exposed our team to a wide variety of testing applications. As a result, we’ve likely created a solution for a challenge similar to yours.
-
Product
Battery Discharger & Capacity Tester
IDCE-CT
-
Fuzhou Fuguang Electronics Co., Ltd.
Each wireless module can monitor 4 batteries simultaneously comparing with the traditional method that each module only canmonitor 1 battery, the new wiring operation become easier because the quantity of new modules needed is only a quarter of old-fashioned modules.
-
Product
Functional Test
cUTS
-
Get the essentials of measurement automation to power tests of simpler PCBAs and subassemblies. compactUTS (cUTS) is a cost-effective platform for automating manual tests of devices with fewer than fifty cable-accessible test points in manufacturing environments with moderate production volume. DUT-specific electrically keyed cables make changeover quick and easy.
-
Product
Conformance Test System
TS-RRM
-
The R&S®TS-RRM 5G and LTE test system is a test solution for running 5G NR and LTE inter-RAT RRM test cases for certification of wireless devices.It is a fully automated conformance test system for running validated RRM conformance test cases. In addition to the RRM test cases required by GCF/PTCRB, the R&S®TS-RRM also supports carrier acceptance specific RRM tests.
-
Product
Die Test Handler
3112
-
Chroma 3112 is a productive pick & place handler for high volume single- or multi-site bare die testing.
-
Product
Isolated Digital I/O 60VDC, 150mA
OTP2 module no.186
-
The National Instruments PXI-6528, PCI-6528, and PXI-6529 Digital I/O Modules are isolated digital I/O interfaces for PCI and PXI. These modules can use inputs from NI 6528 and PXI 6529 devices to capture the status of sensors, actuators, and logic devices. NI 6528 devices have 24 SSR outputs for switching external devices with input currents up to 150 mA. The NI 6528 and PXI-6529 devices are suitable for a variety of applications, from automotive development and industrial factory automation to aerospace, laboratory research, and biomedical applications due to their high current handling capacity and isolation.
-
Product
Electrostatic Discharge Testing
-
MET Labs offers special ESD testing services at controlled temperature and humidity, in a specially-designed and dedicated chamber.The chamber consists of ESD waveform verification setup and tables that accommodate a variety of EUTs. The chamber has a capability to vary the relative humidity from 15% to 65% and temperature from 18°C to 24°C.
-
Product
Electrostatic Discharge Generator
SKS-0230I
-
Shanghai Sanki Electronic Industries Co., Ltd.
The electrostatic discharge generator SKS-0230I has high reliability, the host itself can withstand 30kV electrostatic discharge test; 7-inch touch LCD screen, simple interface, convenient operation; unique combination test mechanism, multiple modes, arbitrary combinations of parameters, continuous testing; Equipped with a file management system, which can save commonly used test parameters, and can also import and export test parameters through U disk; has temperature and humidity monitoring function, real-time display of temperature and humidity indicators of the experimental environment; high- pressure precision resistance and capacitance combination, long service life, and Easy to replace to meet different experimental requirements (150pF, 330pF, 330Ω, 2000Ω);
-
-
Product
Glow Discharge Optical Emission Spectrometer
GD-Profiler 2™
-
The GD-Profiler 2™ provides fast, simultaneous analysis of all elements of interest including the gases nitrogen, oxygen, hydrogen and chlorine. It is an ideal tool for thin and thick films characterization and process studies.
-
Product
MINI Battery Discharger & Capacity Tester
IDCE-4815CT
-
Fuzhou Fuguang Electronics Co., Ltd.
IDCE-4815CT can provide 0-150A (steps:1A) adjustable current for different test requests
-
Product
Cable Partial Discharge (PD) Spot Testing And Locating
PrecisePD
-
PrecisePD is an on-line PD Spot Testing and PD location system for Cables and Switchgear with advanced signal processing, used for the detection of PD in high noise environments.
-
Product
Ethernet and Fibre Channel Test Platform
SierraNet M1288
-
The SierraNet M1288 Ethernet and Fibre Channel test platform provides best in class analysis, jamming and generation for traffic capture and manipulation for testing application and link characteristics. SierraNet M1288 is the latest in the line of industry leading test and measurement tools from Teledyne LeCroy, designed for today’s high-speed storage and communications fabrics. SierraNet M1288 supports examination and modification of Ethernet and Fibre Channel links utilizing both Pulse Amplitude Modulation 4 (PAM4) and legacy Non-Return to Zero (NRZ) technologies.
-
Product
6TL24 Combinational Base Test Platform
H71002400
-
The 6TL24 is the Base platform ideal for Combinational test (ICT+FCT) in low to mid volume, high-mix electronics productions. A dual-stage pushing mechanism will allow performing both, the FCT and the ICT test, without the need of changing the test platform and with a low cost fixturing technology. To do so, the exchangeable cassette fixture must be designed with two-level probes. IN the 6TL24, the second level is reached thanks to a pneumatic actuator.
-
Product
4-Module ICT System, I307x Series 6
E9903G
-
Test efficiency, test system stability, and seamless equipment integration. Keysight’s i3070 Series 6 family provides those improvements built upon a proven technology foundation. With time-tested software, hardware, and programmability, the Series 6 are fully backward compatible with previous systems, and they make highly repeatable measurements.
-
Product
Functional Test
UTS
-
The UTS functional test system is perfect for electronics manufacturing operations that have a mix of products where operators load and unload devices under test (DUT) and routinely change out fixtures for each type of DUT.
-
Product
Partial Discharge
-
Partial discharge (PD) is a local electrical discharge that occurs in imperfections or inhomogeneities. The partial discharge measurement is a so-called “non destructive test” to determine the quality of insulating materials. On the contrary of pure high-voltage test, th test item is not pre-damaged at low PD levels.
-
Product
Functional Test System
TS-5040
-
The Keysight TS-5040 Functional Test System is a cost effective, robust and reliable test system that gives you the lowest cost of ownership. In addition, the open architecture Test Exec SL gives you the flexibility to do just about anything you want.
-
Product
Partial Discharge Testing
-
Weshine Electric Manufacturing Co., Ltd
Using the Windows system operating platform, you can freely choose ellipse, straight line, sine wave display, two-dimensional, three-dimensional graphic analysis mode, spectrum window, Q-V-F three-dimensional characteristic window, and static detailed measurement, observation and analysis of partial discharge pulse of one-cycle test voltage .
-
Product
Lightning discharge counters
CDR-401
-
CDR-401 is the new counter which complies with the latest applicable Lightning Protection related Standards.
-
Product
Lens Module Test Platform
-
The Lens Module Test Platform is a flexible solution to deliver the quality that is expected from your brand for all types of lenses and cameras. The system can be configured to measure objective, eyepiece or camera lenses. As the platform can efficiently measure lenses as small as 2 mm3, it is perfect for the critically precise applications of life sciences, consumer electronics, automotive and other industries. With 25+ years of quality experience, the Lens Module Test Platform ensures that all products shipped to market work as intended.
-
Product
Safe Discharge Rods
-
These instruments will allow you to conduct the safe damp discharge of the residual charge on the cable / equipment by limiting the discharge current.
-
Product
Test Solutions
AT/CX/CM Series
-
The VeEX AT/CX/CM series are next generation test solutions designed for analog and digital cable TV networks supporting VoIP, WiFi, and Internet service. Analog and Digital SLM, ingress noise sweep, deep interleave support, and QAM constellation analysis are among many standard features. Enhanced optional features include QAM16/64/128 Upstream Generation (USG), Reverse Path QAM Analysis, and DOCSIS 2.0/DOCSIS 3.0 Cable Modem emulation. A high capacity LiIon battery pack provides extended autonomy for a full day use with only a single charge.
-
Product
Shock Test
-
Shock testing determines the ability of equipment to withstand the infrequent non-repetitive shocks encountered in handling, transportation, and service and to continue to function, where required. Also, shock tests verify that equipment will not detach from its mounting during these tests.
-
Product
Test And Measurement
-
Test and Measurement supplies test, measurement, and analysis equipment and software for product design optimisation, manufacturing control, and environmental monitoring systems. Markets are principally the aerospace, automotive, consumer electronics and oil and gas industries. For customers in the automotive and aerospace industries, our products and applications help them to design and test new products whilst reducing time to market. In consumer electronics, our equipment and software enable customers to refine the performance and accuracy of their products and to test them in the production process. In the environmental monitoring market, the desire for higher standards of community comfort is creating additional demand. In the oil and gas industries, our products and solutions optimise the recovery rates of oil and gas reservoirs and support the development of cost-efficient extraction processes in a safe manner that minimises the impact on the local environment. The operating companies in this segment are Brüel & Kjær Sound & Vibration, ESG Solutions, HBM and Millbrook.
-
Product
Automatic Test
-
Test Systems of varied sizes and complexity are a specialty of EJC Systems. From concept through development, fabrication, and customer integration, the EJC Systems team brings experience and expertise to ensure every customer receives exactly what was requested.
-
Product
Leakage Test
-
Leakage current and discharge current depend on the insulation of the device. The measurement simulates various fault situations that could occur during operation. The test determines whether the measured current is within the permissible limits and poses no danger to the user in case of a fault.
-
Product
Test Engineering
-
TestEdge engineers have an average of 17 years of engineering experience in test, packaging, and fixturing. This experience is across a wide spectrum of products, customers, and ATE platforms. We have experience in all of the following:Digital, analog, mixed-signal, RF Test programming servicesRemote test capability Semi-automatic test generation Automatic data collection and reduction High performance test fixturing Format independant vector translation High power testing with liquid cooling
-
